共查询到20条相似文献,搜索用时 155 毫秒
1.
Ta2O5 and Nb2O5 films are deposited on BK7 glass substrates using an electron beam evaporation method and are annealed at 673 K in the air.In this letter,comparative studies of the optical transmittance,microstructure,chemical composition,optical absorption,and laser-induced damage threshold(LIDT) of the two films are conducted.Findings indicate that the substoichiometric defect is very harmful to the laser damage resistance of Ta2O5 and Nb2O5 films.The decrease of absorption improves the LIDT in films deposited by the same material.However,although the absorption of the Ta2O5 single layer is less than that of the Nb2O5 single layer,the LIDT of the former is lower than that of the latter.High-reflective(HR) coatings have a higher LIDT than single layers due to the thermal dissipation of the SiO2 layers and the decreased electric field intensity(EFI).In addition,the Nb2O5 HR coating achieves the highest LIDT at 25.6 J/cm 2 in both single layers and HR coatings. 相似文献
2.
ZrO2 films are deposited by the electron-beam evaporation method. Parts of the prepared samples are post-treated with oxygen plasma at the environment temperature. The laser-induced damage threshold (LIDT) of the films increases from 15.9 to 23.1 J/cm2 after treatment with oxygen plasma. Compared with that of the as-grown samples, significant reduction of the average microdefect density and absorption are found after oxygen-plasma posttreatment. These results indicate that the oxygen-plasma posttreatment technique is an effective and simple method for reducing the microdefect density and absorption to improve the LIDT. 相似文献
3.
Temperature dependences of optical properties,chemical composition,structure,and laser damage in Ta2O5 films 下载免费PDF全文
Ta2O5 films are prepared by e-beam evaporation with varied deposition temperatures,annealing temperatures,and annealing times.The effects of temperature on the optical properties,chemical composition,structure,and laserinduced damage threshold(LIDT) are systematically investigated.The results show that the increase of deposition temperature decreases the film transmittance slightly,yet annealing below 923 K is beneficial for the transmittance.The XRD analysis reveals that the film is in the amorphous phase when annealed below 873 K and in thehexagonal phase when annealed at 1073 K.While an interesting near-crystalline phase is found when annealed at 923 K.The LIDT increases with the deposition temperature increasing,whereas it increases firstly and then decreases as the annealing temperature increases.In addition,the increase of the annealing time from 4 h to 12 h is favourable to improving the LIDT,which is mainly due to the improvement of the O/Ta ratio.The highest LIDT film is obtained when annealed at 923 K,owing to the lowest density of defect. 相似文献
4.
Ta2O5 films were prepared with conventional electron beam evaporation and annealed in O2 at 673 K for 12 h. Laser-induced damage thresholds (LIDTs) of the films were performed at 532 and 1064 nm in 1-on-1 regime firstly, and then were performed at 532, 800, and 1064 nm in n-on-1 regime, respectively.The results showed that the LIDTs in n-on-1 regime were higher than that in 1-on-1 regime at 532 and 1064 nm. In addition, in n-on-1 regime, the LIDT increased with the increase of wavelength. Furthermore, both the optical property and LIDT of Ta2O5 films were influenced by annealing in O2. 相似文献
5.
主要讨论了电子束蒸发SiO2/HfO2薄膜的面形控制和损伤性能。研究了电子束蒸发工艺参数对薄膜应力以及面形的影响;分析了制备工艺对薄膜吸收、节瘤缺陷密度的影响,测量了制备薄膜的损伤阈值。研究结果表明:调整SiO2蒸发时的氧分压可以有效地将薄膜的应力控制在-250~-50 MPa。同时采用金属Hf蒸发可以显著地将节瘤缺陷密度从12.6 mm-2降低至2.7 mm-2,同时将损伤阈值从30 J/cm2提高至55 J/cm2。 相似文献
6.
SiO2 films were deposited on K9 substrate by the electron-beam evaporation method. The influence of oxygen-plasma posttreatment on the properties of SiO2 films was investigated. After oxygen-plasma treatment, it was found that the microdefect density of films reduced. We deduced that the absorption of films also reduced. The treated sample exhibited higher LIDT value compared with the as-deposited sample. However, this study is the preliminary work and optimization by this method will be discussed in our future work. 相似文献
7.
Ta2O5/SiO2 dielectric mirrors deposited by ion beam sputtering (IBS) are studied. The multi-shot laserinduced damage threshold (LIDT) and its dependence on the number of shots are investigated, after which we find that the multi-shot LIDT is lower than that of single-shot. The accumulation effects of defects play an important role in the multi-shot laser damage. A simple model, which includes the conduction band electron production vsa multiphoton and impact ionizations, is presented to explain the experimental phenomena. 相似文献
8.
9.
We investigate the laser damage behaviour of an electron-beam-deposited TiO2 monolayer at different process parameters. The optical properties, chemical composition, surface defects, absorption and laser-induced damage threshold (LIDT) of films are measured. It is found that TiO2 films with the minimum absorption and the highest LIDT can be fabricated using a TiO2 starting material after annealing. LIDT is mainly related to absorption and is influenced by the non-stoichiometric defects for TiO2 films. Surface defects show no evident effects on LIDT in this experiment. 相似文献
10.
利用电子束蒸发和光电极值监控技术制备了氧化铪薄膜,并分别用两种后处理方法(空气中退火和氧等离子体轰击)对样品进行了处理.然后,对样品的透过率、吸收和抗激光损伤阈值进行了测试分析.实验结果表明,两种后处理方法都能不同程度地降低了氧化铪薄膜的吸收损耗、提高了抗激光损伤阈值.实验结果还表明,氧等离子体轰击的后处理效果明显优于热退火,样品的吸收平均值在氧等离子体后处理前后分别为34.8 ppm和9.0 ppm,而基频(1 064 nm)激光损伤阈值分别为10.0 J/cm2和21.4 J/cm2. 相似文献
11.
Working Pressure Dependence of Properties of Al2O3 Thin Films Prepared by Electron Beam Evaporation 下载免费PDF全文
The effects of working pressure on properties of Al2O3 thin films are investigated. Transmittance of the Al2O3 thin film is measured by a Lambda 900 spectrometer. Laser-induced damage threshold (LIDT) is measured by a Nd:YAG laser at 355 nm with a pulse width of 7ns. Microdefects were observed under a Nomarski microscope. The samples are characterized by optical properties and defect, as well as LIDT under the 355 nm Nd:YAG laser radiation. It is found that the working pressure has fundamental effect on the LIDT. It is the absorption rather than the microdefect that plays an important role on the LIDT of Al2O3 thin film. 相似文献
12.
13.
Zirconium dioxide (ZrO2) thin films were deposited on BK7 glass substrates by the electron beam evaporation method. A continuous wave CO2 laser was used to anneal the ZrO2 thin films to investigate whether beneficial changes could be produced. After annealing at different laser scanning speeds by CO2 laser, weak absorption of the coatings was measured by the surface thermal lensing (STL) technique, and then laser-induced damage threshold (LIDT) was also determined. It was found that the weak absorption decreased first, while the laser scanning speed is below some value, then increased. The LIDT of the ZrO2 coatings decreased greatly when the laser scanning speeds were below some value. A Nomarski microscope was employed to map the damage morphology, and it was found that the damage behavior was defect-initiated both for annealed and as-deposited samples. The influences of post-deposition CO2 laser annealing on the structural and mechanical properties of the films have also been investigated by X-ray diffraction and ZYGO interferometer. It was found that the microstructure of the ZrO2 films did not change. The residual stress in ZrO2 films showed a tendency from tensile to compressive after CO2 laser annealing, and the variation quantity of the residual stress increased with decreasing laser scanning speed. The residual stress may be mitigated to some extent at proper treatment parameters. 相似文献
14.
Cheng Xu Hongcheng Dong Lei Yuan Hongbo He Zhengxiu Fan 《Optics & Laser Technology》2009,41(3):258-263
Ta2O5 films were deposited using the conventional electron beam evaporation method and then annealed at temperatures in the range 373-673 K. Chemical composition, scattering and absorption were examined by X-ray photoelectron spectroscopy (XPS), total integrated scattering (TIS) measurement and the surface thermal lensing (STL) technique, respectively. The laser-induced damage threshold (LIDT) was assessed using the output from an Nd:YAG laser with a pulse length of 12 ns. The results showed that the improvement of the LIDT after annealing was due to the reduced substoichiometric and structural defects present in the film. The LIDT increased slightly below 573 K and then increased significantly with increase in annealing temperature, which could be attributed to different dominant defects. Moreover, the root mean square (RMS) roughness and scattering had little effect on the LIDT, while the absorption and the LIDT were in accord with a general relation. 相似文献
15.
16.
17.
18.
Cheng Xu Qiling Xiao Jianyong Ma Yunxia Jin Zhengxiu Fan 《Applied Surface Science》2008,254(20):6554-6559
Ta2O5 films were deposited by conventional electron beam evaporation method and then annealed in air at different temperature from 873 to 1273 K. It was found that the film structure changed from amorphous phase to hexagonal phase when annealed at 1073 K, then transformed to orthorhombic phase after annealed at 1273 K. The transmittance was improved after annealed at 873 K, and it decreased as the annealing temperature increased further. The total integrated scattering (TIS) tests and AFM results showed that both scattering and root mean square (RMS) roughness of films increased with the annealing temperature increasing. X-ray photoelectron spectroscopy (XPS) analysis showed that the film obtained better stoichiometry and the O/Ta ratio increased to 2.50 after annealing. It was found that the laser-induced damage threshold (LIDT) increased to the maximum when annealed at 873 K, while it decreased when the annealing temperature increased further. Detailed damaged models dominated by different parameters during annealing were discussed. 相似文献
19.
Comparison of TiO2 and ZrO2 Films Deposited by Electron-Beam Evaporation and by Sol-Gel Process 下载免费PDF全文
TiO2 and ZrO2 films are deposited by electron-beam (EB) evaporation and by sol-gel process. The film properties are characterized by visible and Fourier-transform infrared spectrometry, x-ray diffraction analysis, surface roughness measure, absorption and laser-induced damage threshold (LIDT) test. It is found that the sol-gel films have lower refractive index, packing density and roughness than EB deposited films due to their amorphous structure and high OH group concentration in the film. The high LIDT of sol-gel films is mainly due to their amorphous and porous structure, and low absorption. LIDT of EB deposited film is considerably affected by defects in the film, and LIDT of sol-gel deposited film is mainly effected by residual organic impurities and solvent trapped in the film. 相似文献
20.
激光弱吸收是导致光学薄膜损伤的重要原因。在(5~43)mPa的氧分压下制备并测试了一组HfO2薄膜。实验发现,当氧分压小于20mPa时,薄膜弱吸收越大,损伤阈值越低;当氧分压大于20mPa时,薄膜的损伤阈值与弱吸收并不一一对应,具有较高弱吸收的薄膜可能同时具有较高的损伤阈值。建立了缺陷模型,采用有限元法模拟了缺陷对弱吸收测量和损伤阈值测量的影响,分析了缺陷尺寸、密度、吸收系数对弱吸收和损伤阈值的影响。研究结果显示,吸收系数高于薄膜1 000倍的缺陷可以降低薄膜的损伤阈值1 000倍,却并不影响薄膜的弱吸收。缺陷对HfO2薄膜的激光弱吸收与损伤阈值测试有完全不同的影响,是导致某些薄膜弱吸收与损伤阈值背离的原因。 相似文献