Laser Induced Damage Threshold at 355 and 1064nm of Ta2O5 Films of Different Phases

Ta2O5 films axe deposited on fused silica substrates by conventional electron beam evaporation method. By annealing at different temperatures, Ta2 O5 films of amorphous, hexagonal and orthorhombic phases are obtained and confirmed by x-ray diffractometer （XRD） results. X-ray photoelectron spectroscopy （XPS） analysis shows that chemical composition of all the films is stoichiometry. It is found that the amorphous Ta2 O5 film achieves the highest laser induced damage threshold （LIDT） either at 355 or 1064nm, followed by hexagonal phase and finally orthorhombic phase. The damage morphologies at 355 and 1064nm are different as the former shows a uniform fused area while the latter is centred on one or more defect points, which is induced by different damage mechanisms. The decrease of the LIDT at 1064nm is attributed to the increasing structural defect, while at 355nm is due to the combination effect of the increasing structural defect and decreasing band gap energy.     

Effect of Process Parameters on Laser Damage Threshold of TiO2 Coatings

We investigate the laser damage behaviour of an electron-beam-deposited TiO2 monolayer at different process parameters. The optical properties, chemical composition, surface defects, absorption and laser-induced damage threshold （LIDT） of films are measured. It is found that TiO2 films with the minimum absorption and the highest LIDT can be fabricated using a TiO2 starting material after annealing. LIDT is mainly related to absorption and is influenced by the non-stoichiometric defects for TiO2 films. Surface defects show no evident effects on LIDT in this experiment.     

Influence of Annealing Temperature on Structure, Optical Loss and Laser-Induced Damage Threshold of TiO2 Thin Films

TiO2 thin films are prepared on fused silica with conventional electron beam evaporation deposition. After annealed at different temperatures for 4h, the spectra and XRD patterns of the TiO2 thin film are obtained. Weak absorption of coatings is measured by the surface thermal lensing technique, and laser-induced damage threshold （LIDT） is determined. It is found that with the increasing annealing temperature, the transmittance of TiO2 films decreases. Especially when coatings are annealed at high temperature over 1173K, the optical loss is very serious. Weak absorption detection indicates that the absorption of coatings decreases firstly and then increases, and the absorption and defects play major roles in the LIDT of TiO2 thin films.     

Ferroelectric Properties of Bi3.25La0.75Ti3O12 Thin Films Crystallized inDifferent N2/O2 Ambients

Bi3.25La0.75 Ti3O12 （BLT） ferroelectric thin films are deposited by sol-gel method and annealed for crystallizaion in total l eccm N2/02 mixed gas with various ratio at 750℃ for 30rain. The effect of crystallization ambient on the structural and ferroelectric properties of the BLT films is studied. The growth direction and grain size of BLT film are revealed to affect ferroeleetric properties. Alter the BLT film is annealed in 20%O2, the largest P~ value is obtained, which is ascribed to an increase of random orientation and large grain size. The fatigue property is improved with the concentration of oxygen in the ambient increasing, which is ascribed to annealing in the ambient with high concentrated oxygen adequately decreasing the defects related to lack of oxygen.     

Working Pressure Dependence of Properties of Al2O3 Thin Films Prepared by Electron Beam Evaporation

The effects of working pressure on properties of Al2O3 thin films are investigated. Transmittance of the Al2O3 thin film is measured by a Lambda 900 spectrometer. Laser-induced damage threshold （LIDT） is measured by a Nd：YAG laser at 355 nm with a pulse width of 7ns. Microdefects were observed under a Nomarski microscope. The samples are characterized by optical properties and defect, as well as LIDT under the 355 nm Nd：YAG laser radiation. It is found that the working pressure has fundamental effect on the LIDT. It is the absorption rather than the microdefect that plays an important role on the LIDT of Al2O3 thin film.     

Structural and electrical properties of La0.5Sr0.5CoO3 films on SrTiO3 and porous a-Al2O3 substrates

Films of La_0.5Sr_0.5CoO₃ (LSCO) have been deposited on specially treated TiO₂-terminated (001) SrTiO₃ substrate surfaces and on macroporous polycrystalline !-Al₂O₃ substrates, having a mean pore diameter of 80 nm, by pulsed laser deposition. The films deposited on SrTiO₃ are good conducting, (001) textured, and exceptionally smooth (1-2 Å for 100 nm thick films). LSCO films deposited on porous !-Al₂O₃ are polycrystalline and exhibit good crystallographic and electrical properties despite the large substrate roughness and the differences in lattice parameters and crystal structure between the film and the substrate. Different growth modes have been observed on the porous !-Al₂O₃ substrates depending on the oxygen pressure during film deposition. Films grown at an oxygen pressure of 10^-1 mbar are macroporous, whereas films grown at 10^-2 mbar completely cover the substrate pores. In the latter case, strain effects lead to film cracking.     

Influence of Ytterbia Content on Residual Stress and Microstructure of Y2O3--ZrO2 Thin Films Prepared by EB-PVD

Y2O3 stabilized ZrO2 （YSZ） thin films with different Y2O3 molar contents （0, 3, 7, and 12 mol%） are deposited on BK7 substrates by electron-beam evaporation technique. The effects of different Y2O3 contents on residual stresses and structures of YSZ thin films are studied. Residual stresses are investigated by means of two different techniques： the curvature measurement and x-ray diffraction method. It is found that the evolution of residual stresses of YSZ thin films by the two different methods is consistent. Residual stresses of films transform from compressive stress into tensile stress and the tensile stress increases monotonically with the increase of Y2O3 content. At the same time, the structures of these films change from the mixture of amorphous and monoclinic phases into high temperature cubic phase. The variations of residual stress correspond to the evolution of structures induced by adding of Y2O3 content.     

Influence of overcoat on laser-induced damage threshold of 532 and 800 nm TiO2/SiO2 high reflectors

TiO₂/SiO₂ high reflectors with and without a SiO₂ overcoat are deposited by electron-beam evaporation. The film properties are characterized by visible spectrometry measures, structure analysis, roughness and laser-induced damage threshold (LIDT) tests, surface defects and damage morphology observation. The effects of overcoats on LIDT at 532 nm, 8 ns and 800 nm, 220 ps laser pulses are investigated. The relations between film structure, roughness, surface defects, electric field and LIDT are discussed. It is found that overcoats can increase the LIDT at these two laser wavelengths. The reduction of peak temperature, the low defects density and roughness, the low intrinsic absorption of SiO₂ and its amorphous structure are the main reasons for LIDT improvement by overcoats.     

A Spectroscopic Ellipsometry Study of TiO2 Thin Films Prepared by dc Reactive Magnetron Sputtering： Annealing Temperature Effect

TiO2 thin films are obtained by dc reactive magnetron sputtering. A target of titanium （99.995%） and a mixture of argon and oxygen gases are used to deposit TiO2 films on to silicon wafers （100）. The crystalline structure of deposited and annealed film are deduced by variable-angle spectroscopic ellipsometry （VASE） and supported by x-ray diffractometry. The optical properties of the films are examined by VASE. Measurements of ellipsometry are performed in the spectral range O. 72-3.55 e V at incident angle 75^o. Several SE models, categorized by physical and optical models, are proposed based on the ＇simpler better＇ rule and curve-fits, which are generated and compared to the experimental data using the regression analysis. It has been found that the triple-layer physical model together with the Cody-Lorentz dispersion model offer the most convincing result. The as-deposited films are found to be inhomogeneous and amorphous, whereas the annealed films present the phase transition to anatase and rutile structures. The refractive index of TiO2 thin films increases with annealing temperature. A more detailed analysis further reveals that thickness of the top sub-layer increases, whereas the region of the bottom amorphous sub-layer shrinks when the films are annealed at 300℃.     

Transport Behaviour of La0.8Sr0.2AlO3 Thin Film on Oxygen Deficient SrTiO3 Substrate

La_0.8Sr_0.2AlO₃ (LSAO) thin films are grown on SrTiO₃ (STO) and MgO substrates by laser molecular beam epitaxy. The LSAO thin film on oxygen deficient STO substrate exhibits metallic behaviour over the temperature range of 80--340K. The optical transmittance spectrum indicates that theLSAO thin films on MgO substrate are insulating at room temperature. The transport properties of LSAO thin films on STO substrates deposited in different oxygen pressure are compared. Our results indicate that oxygen vacancies in STO substrates should be mainly responsible for the transport behaviour of LSAO thin films.     

Piezoelectric Pb0.7La0.2TiO3 prepared by pulsed laser deposition on (100)InP

La-modified PbTiO₃ (PLT) thin films have been deposited by pulsed laser deposition on (100)InP substrates. The nominal target composition was selected to optimize piezoelectric properties of the material. It is shown that PLT deposition on as-received InP produces amorphous PLT films because of the presence of a native oxide on the substrate. PLT films deposited on bare InP have poor adhesion as a result of the surface reoxidation of the substrate due to the high oxygen pressure required for the deposition of stoichiometric PLT. To prevent substrate oxidation, several buffer oxides (CeO₂, ZrO₂, SrO, Y-stabilized ZrO₂, MgO, and SrTiO₃) have been grown in vacuum on (100)InP. Highest-quality heteroepitaxy was found with Y-stabilized ZrO₂ (YSZ), being 𘜄¢{100} YSZ𘜄¢{100} InP oriented. The PLT deposited on this buffer layer is oriented with the [101] direction perpendicular to the substrate surface plane.     

Effects of annealing on laser-induced damage threshold of TiO2/SiO2 high reflectors

The mechanism of improving 1064 nm, 12 ns laser-induced damage threshold (LIDT) of TiO₂/SiO₂ high reflectors (HR) prepared by electronic beam evaporation from 5.1 to 13.1 J/cm² by thermal annealing is discussed. Through optical properties, structure and chemical composition analysis, it is found that the reduced atomic non-stoichiometric defects are the main reason of absorption decrease and LIDT rise after annealing. A remarkable increase of LIDT is found at 300 °C annealing. The refractive index and film inhomogeneity rise, physical thickness decrease, and film stress changes from compress stress to tensile stress due to the structure change during annealing.     

Electroluminescence from Multilayered Diamond/CeF3/SiO2 Films

We report a thin film electroluminescent device with a three-layer structure （diamond/CeF3/SiO2 films）, which has a luminance of 1.5 cd/m^2 at dc voltage 215 V. The electroluminescence spectrum at room temperature shows that the main peaks locate at 527 and 593nm, which are attributed to isolated emission centers of Ce^3＋ ions.     

Effects of Different Dispersion Methods on the Microscopical Morphology of TiO2 Film

Nanocrystalline porous TiO2 films were prepared on conducting glass supports （ITO） by processed commercial TiO2 nanometre powder （P25）. Three methods of physical dispersing for TiO2 powder, i.e. grinding, magnetic stirring, sonicleaning, were used to disperse TiO2 nanometre powder. Surface morphologies of TiO2 films were observed by optic-microscope and SEM. It is found that the surface morphologies of TiO2 films are determined not only by the dispersing methods but also by the percentage of TiO2 powder in the dispersing system. Different film morphologies can be obtained under the same preparation condition but with different dispersing methods. A lot of cracks exist on the film surface for which the TiO2 slurry is dispersed by grinding. Magnetic stirring leads to some white points and micro-holes on the film surface. Only a few of micro-holes can be observed on the film surface, in which the TiO2 slurry is dispersed by sonicleaning. Different surface morphologies can also be found with different thicknesses of TiO2 films. Different film thicknesses are due to different percentages of TiO2 powder in the slurry. The related mechanism leading to different features of the surface morphologies for the TiO2 films is discussed.     

Influence of negative ion element impurities on laser induced damage threshold of HfO2 thin film

Negative ion element impurities breakdown model in HfO₂ thin film was reported in this paper. The content of negative ion elements were detected by glow discharge mass spectrum analysis (GDMS); HfO₂ thin films were deposited by the electron-beam evaporation method. The weak absorption and laser induced damage threshold (LIDT) of HfO₂ thin films were measured to testify the negative ion element impurity breakdown model. It was found that the LIDT would decrease and the absorption would increase with increasing the content of negative ion element. These results indicated that negative ion elements were harmful impurities and would speed up the damage of thin film.     

Preferential orientation of modified SrBi2Nb2O9 ferroelectric thin films prepared by pulsed laser deposition

We report on the deposition of SrBi₂Nb₂O₉ and Sr_1-xNa_xBi_2-xTe_xNb₂O₉ ferroelectric thin films on Pt/TiO₂/SiO₂/(100)Si substrates using the pulsed laser deposition technique. Deposition on substrates heated to 600-700 °C produces {11l} film texture and dense films with grain sizes up to about 500 nm. The recrystallization at 700 °C of amorphous films deposited at lower temperatures enhances the contribution of the {100} and {010} orientations. These films show smaller grain size, namely 50-100 nm. {11l}-oriented Sr_1-xNa_xBi_2-xTe_xNb₂O₉ films have remnant polarization P_rۆ 7C/cm², a coercive field E_c䏐 kV/cm and dielectric constant, )𪓴. The low value of P_r is probably related to the low fraction of grains with the ferroelectric axis in the direction of the applied field, E. The recrystallized films have more grains with the ferroelectric axis parallel to E; however, they have a low resistivity which so far has prevented electrical characterization.     

Femtosecond Third-Order Optical Nonlinearity of Au：Bi203 Nanocomposite Films

Ultrafast third-order optical nonlinearities of the as-deposited and annealed Au：Bi2O3 nanocomposite films deposited by magnetron cosputtering are investigated by using femtosecond time-resolved optical Kerr effect （OKE） and pump probe techniques. The third-order optical nonlinear susceptibility is estimated to be 2.6Ф×10^- 10 esu and 1.8 × 10.9 esu at wavelength of 800nm, for the as-deposited and the annealed film, respectively. The OKE signal of the as-deposited film is nearly temporally symmetrical with a peak centred at zero delay time, which indicates the dominant contribution from intraband transition of conduction electrons. For the annealed film, the existence of a decay process in OKE signal implies the important contribution of hot electrons. These characteristics are in agreement with the hot electron dynamics observed in pump probe measurement.     

LaNiO3 under-electrode layers for the growth of textured (Pb0.4Zr0.6)TiO3 thin films using pulsed laser deposition

We investigated the structural properties of LaNiO₃ thin films of three different thicknesses deposited by pulsed laser deposition on Si(001) mainly by using a synchrotron X-ray scattering measurement. The LaNiO₃ thin films were grown with the (00l) preferred growth direction, showing completely random distribution in the in-plane direction. In the early stage of the growth, the film was almost unstrained. However, as the film grew further, tensile strain was markedly involved. Also its surface became rougher but its crystalline quality improved significantly with increasing film thickness. A completely (00l)-oriented (Pb_0.4Zr_0.6)TiO₃ thin film was successfully grown on such a LaNiO₃/Si(001) substrate at a substrate temperature of 350 °C by using the same pulsed laser deposition. Our results show that the LaNiO₃ film can serve effectively as a bottom electrode layer for the preparation of a well-oriented (Pb_0.4Zr_0.6)TiO₃ thin film on Si substrates.     

An All-Thin-Film Electrochromic Device Composed of MoO3--LiBSO--NiOx Multilayer Structure

An all-thin-tilm （ATF） electrochromic device for modulating the optical transmittance is manufactured using magnetron sputtering. The devices consists of MoO3 as the main electrochromic layer, LiBO2 ＋Li2SO4 （LiBSO） as the ion conductor layer, and NiOx as the complementary electrochromic layer. Glass covered with indium tin oxide （ITO） is used as the substrate and the ITO film is used as the bottom electrode. The ITO film deposited on the top of the devices is used as the other electrode. The structure and morphology of the films are characterized by x-ray diffraction （XRD） and scanning electron microscopy （SEM）. The devices exhibit good optical properties with low transmittance values in the coloured state, and the optical modulation is measured by spectrophotometer in the wavelength range from 400 to 800nm. The average visible light transmittance reaches 50.2% and 3.7% in bleached and coloured state, respectively. The results indicate that such a monolithic system has great potential to be applied in smart windows.     

Low-temperature growth of Y2O3 thin films by ultraviolet-assisted pulsed laser deposition

Thin Y₂O₃ films have been grown on (100) Si using an in-situ ultraviolet-assisted pulsed laser deposition (UVPLD) technique. When compared to conventional pulsed laser deposited (PLD) films under similar conditions, the UVPLD-grown films exhibited better structural and optical properties, especially those grown at lower substrate temperatures, from 200 °C to 400 °C. X-ray diffraction investigations showed that the films grown were highly crystalline and textured. According to X-ray photoelectron spectroscopy and Rutherford backscattering spectrometry investigations, UVPLD-grown Y₂O₃ films have a better overall stoichiometry and contain less physisorbed oxygen than the conventional PLD-grown films. The refractive index values, measured in the range 300-750 nm by using variable-angle spectroscopic ellipsometry, were similar to those of a reference Y₂O₃ film.