用SiCl4/H2气源沉积多晶硅薄膜光照稳定性的研究

对以SiH₄/H₂及SiCl₄/H₂为源气体、采用 等离子体增强化学气相沉积技术制备的非晶硅薄膜和多晶硅薄膜进行了光照稳定性的研究.实验表明，制备的多晶硅薄膜并没有出现 非晶硅中的光致衰减现象，其光电导、暗电导在光照过程中没有下降反而有所上升且电导率 变化快慢受氢稀释度的制约.多晶硅薄膜的光照稳定性可能来源于高的晶化度及Cl元素的存在. 关键词： 多晶硅薄膜 稳恒光电导效应 晶界 光致衰退效应     

氢稀释对高速生长纳米晶硅薄膜晶化特性的影响

以SiH₄与H₂为气源,采用射频等离子体增强化学气相沉积技术,在较高的压强(230Pa)下,研究氢稀释率对纳米晶硅薄膜的生长速率和晶化特性的影响. 实验表明,薄膜的晶化率,晶粒尺寸随着氢稀释率的提高而增加,当氢稀释率为99%,薄膜的晶化率接近70%. 而沉积速率却随着氢稀释率的减小而增加,当氢稀释率从99%减小到95%时,薄膜的沉积速率由0.3nm/s 增加至0.8nm/s. 关键词： 纳米晶硅薄膜 氢稀释 晶化率 硅烷     

大气压等离子体辅助多晶硅薄膜化学气相沉积参数诊断

本文采用发射光谱法诊断了大气压下Ar气、SiCl₄及H₂气混合气体（Ar/SiCl₄/H₂）射频放电等离子体射流特性.利用Si原子谱线强度计算了电子激发温度并以此估算了Si原子数密度,研究了射频功率及气体流量对电子激发温度和Si原子数密度以及SiCl₄解离率的作用. 关键词： 大气压等离子体射流 发射光谱 电子激发温度 多晶硅薄膜沉积     

高氢稀释制备微晶硅薄膜微结构的研究

采用高氢稀硅烷热丝化学气相沉积方法制备氢化微晶硅薄膜.其结构特征用Raman谱，红外透射谱，小角X射线散射等来表征.结果表明微晶硅的大小及在薄膜中的晶态比χ_c随氢稀释度的提高而增加.而从红外谱计算得到氢含量则随氢稀释度的增加而减少.小角X射线散射结果表明薄膜致密度随氢稀释度的增加而增加.结合红外谱和小角X射线散射的结果讨论与比较了不同相结构下硅网络中H的键合状态.认为随着晶化的发生和晶化程度的提高H逐渐移向晶粒表面，在硅薄膜中H的存在形式从以SiH为主向SiH₂ 关键词：     

热丝化学气相沉积技术低温制备多晶硅薄膜的结构与光电特性

以金属W和Ta为热丝，采用热丝化学气相沉积 ，在250℃玻璃衬底上沉积多晶硅薄膜.研究了热丝温度、沉积气压、热丝与衬底间距等沉积参数对硅薄膜结构和光电特性的影响，在优化条件下获得晶态比X_c＞90%，暗电导率σ_d=10^-7—10-6Ω ^-1cm^-1，激活能E_a=0.5eV，光能隙E_opt≤1.3 eV的多晶硅薄膜. 关键词： 多晶硅薄膜 热丝化学气相沉积 光电特性     

H2对Ar稀释SiH4等离子体CVD制备多晶硅薄膜的影响

以SiH₄，Ar和H₂为反应气体，采用射频等离子体化学气相沉积方法在300℃下制备了低温多晶Si薄膜.实验发现，反应气体中H₂的比例是影响薄膜结晶质量的重要因素，在适量的H₂比例下制备的多晶Si薄膜具有结晶相体积分数高，氢含量低，生长速率快、抗杂质污染等特性. 关键词： 低温多晶Si薄膜 等离子体CVD 4')" href="#">Ar稀释SiH₄ 2比例')" href="#">H₂比例     

氮化硅薄膜中纳米非晶硅颗粒的键合结构及光致发光

采用螺旋波等离子体化学气相沉积技术以N₂/SiH₄/H₂为反应气体制备了镶嵌有纳米非晶硅颗粒的氢化氮化硅薄膜,通过改变N₂流量实现了薄膜从红到蓝绿的可调谐光致发光.傅里叶红外透射和紫外-可见光吸收特性分析表明,所生长薄膜具有较高的氢含量,N₂流量增加使氢的键合结构发生变化,非晶硅颗粒尺寸减小,所对应的薄膜的光学带隙逐渐增加和微观结构有序度减小.可调光致发光(PL)主要来源于纳米硅颗粒的量子限制效应发光,随N₂流量增加,PL的谱线展宽并逐渐增强. 关键词： 傅里叶红外透射谱 光吸收谱 纳米硅粒子镶嵌薄膜 光致发光     

氢稀释对纳米晶硅薄膜晶化特性的影响及薄膜生长机理

以SiH4与H2作为前驱气体,采用射频等离子增强化学气相沉积技术制备了纳米晶硅薄膜.利用Raman散射和红外吸收光谱等技术,对不同氢稀释比条件下薄膜的微观结构和键合特性进行了研究.结果表明,随着氢稀释比增加,薄膜的晶化率明显提高,而氢稀释比过高时,薄膜晶化率呈现减少趋势.红外吸收光谱分析表明,纳米晶硅薄膜中氢的键合模式与薄膜的晶化特性密切相关.随着氢稀释比增加,薄膜中整体氢含量和SiH2键合密度明显减少,而在高氢稀释比条件下,氢稀释比增加导致薄膜中SiH2键合密度和整体氢含量增加.     

用SiCl4/H2气源沉积多晶硅薄膜光照稳定性的研究

对以SiH4/H2及SiCl4/H2为源气体、采用等离子体增强化学气相沉积技术制备的非晶硅薄膜和多晶硅薄膜进行了光照稳定性的研究.实验表明,制备的多晶硅薄膜并没有出现非晶硅中的光致衰减现象,其光电导、暗电导在光照过程中没有下降反而有所上升且电导率变化快慢受氢稀释度的制约.多晶硅薄膜的光照稳定性可能来源于高的晶化度及Cl元素的存在.     

H2， He混合稀释生长微晶硅锗薄膜

采用H₂,He混合气体稀释等离子辅助反应热化学气相沉积法生长微晶硅锗薄膜,并在生长过程中对等离子体进行光发射光谱在线监测.结果表明：混合气体稀释法可以有效提高等离子体中的原子氢数目,降低等离子体中的电子温度;用XRD和光暗电导率表征样品的微结构和光电特性时发现,通过优化混合稀释气体中He和H₂气体的比例,能够减少薄膜中的缺陷态,促进薄膜<220>择优取向生长,有效改善微晶硅锗薄膜结构,提高光电吸收性能. 关键词： 化学气相沉积 微晶硅锗薄膜 光发射光谱 X射线衍射     

氢稀释对FTS沉积a-Si:H薄膜结构特性的影响

采用对靶磁控反应溅射技术,以氢气作为反应气体在不同的氢稀释比条件下制备了氢化非晶硅薄膜.利用台阶仪、傅里叶红外透射光谱、Raman谱和紫外-可见光透射谱测量研究了不同氢稀释比对氢化非晶硅薄膜生长速率和结构特性的影响.分析结果发现,利用对靶磁控溅射技术能够实现低温快速沉积高质量氢化非晶硅薄膜的制备.随着氢稀释比不断增加,薄膜沉积速率呈现先减小后增大的趋势.傅里叶红外透射光谱表明,氢化非晶硅薄膜中氢含量先增大后变小.而Raman谱和紫外-可见光透射谱分析发现,氢稀释比的增加使氢化非晶硅薄膜有序度和光学带隙均先增大后减小.可见,此技术通过改变氢稀释比R能够实现氢化非晶硅薄膜结构的有效控制.     

Preparation of hydrogenated microcrystalline silicon films with hot-wire-assisted MWECR-CVD system

Intrinsic hydrogenated microcrystalline silicon (\muc-Si:H) films have been prepared by hot-wire-assisted microwave electron-cyclotron-resonance chemical vapour deposition (HW-MWECR-CVD) under different deposition conditions. Fourier-transform infrared spectra and Raman spectra were measured. Optical band gap was determined by Tauc plots, and experiments of photo-induced degradation were performed. It was observed that hydrogen dilution plays a more essential role than substrate temperature in microcrystalline transformation at low temperatures. Crystalline volume fraction and mean grain size in the films increase with the dilution ratio (R=H₂/(H₂+SiH₄)). With the rise of crystallinity in the films, the optical band gap tends to become narrower while the hydrogen content and photo-induced degradation decrease dramatically. The samples, were identified as \mu c-Si:H films, by calculating the optical band gap. It is considered that hydrogen dilution has an effect on reducing the crystallization activation energy of the material, which promotes the heterogeneous solid-state phase transition characterized by the Johnson--Mehl--Avrami (JMA) equation. The films with the needed structure can be prepared by balancing deposition and crystallization through controlling process parameters.     

Effect of Ar in the source gas on the microstructure and optoelectronic properties of microcrystalline silicon films deposited by plasma-enhanced CVD

Hydrogenated microcrystalline silicon films have been prepared by plasma-enhanced chemical vapor deposition technique using silane diluted in H₂ or H₂ + Ar. The microstructures for silicon films have been evaluated by Raman scattering spectroscopy, X-ray diffraction and Fourier-transform infrared spectroscopy. Optical characterization has been done by UV-vis spectroscopy. It is found that the addition of Ar in diluent gases efficiently improves the deposition rate and crystallinity due to an enhanced dissociation of the source gas and the energy of deexcitation of Ar* released within the growth zone. Meanwhile, the enhanced crystallinity and the reducing of hydrogen ion bombardment with increasing Ar dilution lead to the polymerization and also a bad passivation of the hydrogen which cause the widening of the optical gap and increase of defect states in the μc-Si films. The absorption coefficient and dark conductivity are found to decrease basically with increasing Ar dilution corresponding to the widening optical gap and more defects. That the activation energy increases with increasing Ar dilution or decreasing hydrogen dilution is due to the fact that more defect states lead to a pulling down of the Fermi level.     

Effect of hydrogen dilution on the optical properties of hydrogenated amorphous silicon-nitrogen films prepared by plasma deposition

The effect of the dilution of silane and nitrogen with hydrogen on the optical properties of hydrogenated amorphous silicon-nitrogen films prepared by plasma deposition has been investigated as functions of the gas-volume ratio γ (= ([SiH₄] + [N₂])/([SiH₄] + [N₂] + [H₂]) and the substrate temperature. The prepared films are characterized by the values of the deposition rate, the optical gap, the Urbach energy, the defect density, the integrated infrared absorption intensity and the refractive index, and by correlations between these parameters and the type of hydrogen- and nitrogen-bonding configurations estimated from infrared absorption spectra. The hydrogen dilution effect is discussed in terms of the above and compared with that in hydrogenated amorphous silicon reported in a previous paper by the present authors. It is pointed out that nitrogen atoms incorporated into the silicon network cause more disorder than incorporated hydrogen atoms, from the γ dependence of the Urbach energy and the integrated infrared intensities associated with the hydrogen and nitrogen bondings.     

Growth characteristics of amorphous-layer-free nanocrystalline silicon films fabricated by very high frequency PECVD at 250 ℃

Amorphous-layer-free nanocrystalline silicon films were prepared by a very high frequency plasma enhanced chemical vapor deposition(PECVD) technique using hydrogen-diluted SiH4 at 250 C.The dependence of the crystallinity of the film on the hydrogen dilution ratio and the film thickness was investigated.Raman spectra show that the thickness of the initial amorphous incubation layer on silicon oxide gradually decreases with increasing hydrogen dilution ratio.High-resolution transmission electron microscopy reveals that the initial amorphous incubation layer can be completely eliminated at a hydrogen dilution ratio of 98%,which is lower than that needed for the growth of amorphous-layer-free nanocrystalline silicon using an excitation frequency of 13.56 MHz.More studies on the microstructure evolution of the initial amorphous incubation layer with hydrogen dilution ratios were performed using Fourier-transform infrared spectroscopy.It is suggested that the high hydrogen dilution,as well as the higher plasma excitation frequency,plays an important role in the formation of amorphous-layer-free nanocrystalline silicon films.     

衬底温度和硼掺杂对p型氢化微晶硅薄膜结构和电学特性的影响

以B₂H₆为掺杂剂,采用射频等离子体增强化学气相沉积技术在玻璃衬底上制备p型氢化微晶硅薄膜.研究了衬底温度和硼烷掺杂比对薄膜的微结构和暗电导率的影响.结果表明：在较高的衬底温度下很低的硼烷掺杂比即可导致薄膜非晶化;在实验范围内,随着衬底温度升高薄膜的晶化率单调下降,暗电导率先缓慢增加然后迅速下降,变化趋势与硼烷掺杂比的影响极为相似.最后着重讨论了p型氢化微晶硅薄膜的生长机理. 关键词： p型氢化微晶硅薄膜 衬底温度 晶化率 电导率     

Effects of high hydrogen dilution ratio on optical properties of hydrogenated nanocrystalline silicon thin films

Hydrogenated nanocrystalline silicon thin films were prepared by plasma enhanced vapor deposition technique. In our experiment, hydrogen dilution ratio R_H was changed mainly, while the other parameters, such as the radio frequency power, the direct current bias value, the chamber pressure, the total gas flow and the substrate temperature were kept constant. The film's surface topography was gained by AFM. The chemical bond was confirmed by Fourier transform infrared spectra. The optical properties were characterized by transmission spectra. To consider absorption peak of stretching vibration mode of SiH₃ at 2140 cm⁻¹ and to reduce the calculation error, a hydrogen content calculation method was proposed. Effects of hydrogen dilution ratio on the deposition rate v and hydrogen content C_H were investigated. The bonding mode and the force constants k of chemical bond, the structural factor f in films were changed by high hydrogen dilution ratio, which gave rise to the shift of absorption peak of infrared stretching mode and the decrease of optical band gap E_g.