利用InAs/GaAs数字合金超晶格改进InAs量子点有源区的结构设计

利用分子束外延技术,通过InAs/GaAs数字合金超晶格代替传统的直接生长InGaAs层的方式,在GaAs(100)衬底上生长了InAs量子点结构并成功制备了1.3μm InAs量子点激光器.通过原子力显微镜和光致荧光谱测试手段,对传统生长模式和数字合金超晶格生长模式的两种样品进行了表征,研究发现采用32周期InAs/GaAs数字合金超晶格样品的量子点密度非常高,发光性能良好.通过与常规生长方式所制备激光器的性能对比,发现采用InAs/GaAs数字合金超晶格生长InAs量子点的有源区也可以得到高质量的激光器.利用该方式生长的InAs量子点激光器的阈值电流为24 mA,相应的阈值电流密度仅为75 A/cm2,最高工作温度达到120℃.InAs/GaAs数字合金超晶格既可以保证生长过程中源炉的温度保持不变,还可以对InGaAs层的组分实现灵活调控.不需要改变生长速度,通过改变InAs/GaAs数字合金超晶格的周期数以及InAs层和GaAs层的厚度,便可以获得任意组分的InGaAs,从而得到不同发光波长的激光器.这种生长方式对量子点有源区的结构设计和外延生长提供了新思路.     

生长温度和结构参数对InGaAs／GaAs量子阱光学特性的影响

研究了不同生长温度下制备的In0.15Ga0.85As/GaAs应变量子阱的PL谱,结果表明,生长温度越高,In偏析和In-Ga互混越严重,同时,导致更多的In脱附,PL谱发光峰蓝移。对不同In含量的和不同InGaAs厚度的InGaAs/GaAs量子阱进行PL谱测试,分析表明In含量<0.2,生长温度低于560℃时,In含量和InGaAs层量子阱的厚度对In偏析、脱附和In-Ga互混基本没有影响。     

应力导致InAs/In0.15Ga0.85As量子点结构中 In0.15Ga0.85As阱层的合金分解效应研究

利用固源分子束外延技术,在In0.15Ga0.85As/GaAs量子阱生长了两个InAs/In0.15Ga0.85As量子点(DWELL)样品.通过改变其中一个InAs DWELL样品中的In0.15Ga0.85As阱层的厚度和生长温度,获得了量子点尺寸增大而且尺寸分布更均匀的结果.结合光致发光光谱(PL)和压电调制光谱(PzR)实验结果,发现该样品量子点的光学性质也同时得到了极大的优化.基于有效质量近似的数值计算结果表明:量子点后生长过程中应力导致In0.15Ga0.85As阱层合金分解机理是导致量子点尺寸和光学性质得到优化的主要原因.     

不同组分InxGa1-xAs(0≤x≤0.3)覆盖层对自组织InAs量子点的影响

研究了不同In组分的InxGa1-xAs(0≤x≤0.3)覆盖层对自组织InAs量子点的结构及发光特性的影响.透射电子显微镜和原子力显微镜表明,InAs量子点在InGaAs做盖层时所受应力较GaAs盖层时有所减小,并且x＝0.3时,InGaAs在InAs量子点上继续成岛.随x值的增大,量子点的光荧光峰红移,但随温度的变化发光峰峰位变化不明显.理论分析表明InAs量子点所受应力及其均匀性的变化分别是导致上述现象的主要原因.     

双层堆垛长波长InAs/GaAs量子点发光性质研究

研究了双层堆垛InAs/GaAs/InAs自组织量子点的生长和光致发光(PL)的物理性质。通过优化InAs淀积量、中间GaAs层厚度以及InAs量子点生长温度等生长条件,获得了室温光致发光1391～1438nm的高质量InAs量子点。研究发现对量子点GaAs间隔层实施原位退火、采用Sb辅助生长InGaAs盖层等方法可以增强高密度(2×1010 cm-2)InAs量子点的发光强度,减小光谱线宽,改善均匀性和红移发光波长。     

不同组分InxGa1-xAs(0≤x≤0.3)覆盖层对自组织InAs量子点的影响

研究了不同In组分的In_xGa_1-xAs(0≤x≤0.3)覆盖层对自组织InAs量子点的结构及发光特性的影响.透射电子显微镜和原子力显微镜表明,InAs量子点在InGaAs做盖层时所受应力较GaAs盖层时有所减小,并且x＝0.3时,InGaAs在InAs量子点上继续成岛.随x值的增大,量子点的光荧光峰红移,但随温度的变化发光峰峰位变化不明显.理论分析表明InAs量子点所受应力及其均匀性的变化分别是导致上述现象的主要原因. 关键词： 量子点 盖层 应力 红移     

液滴外延下生长参数对InAs纳米结构形貌的影响

利用液滴外延法在GaAs(001)衬底表面制备InAs量子点，通过控制变量分别研究沉积速率、沉积量对In液滴在GaAs表面生长过程中的影响.使用原子力显微镜(Atomic Force Microscope, AFM)表征InAs纳米结构形貌，得出结论：(1)沉积速率主要通过影响In液滴成核率来控制液滴的密度，即随着沉积速率的增大，In原子在衬底表面的成核率增加，InAs量子点密度增加，实验符合生长动力学经典成核理论.(2)沉积量的改变主要影响液滴的熟化过程，即随着沉积量的增大，可参与生长的活跃的In原子增加，促进了液滴熟化，使得扩散坍塌的原子数量增加，导致在InAs纳米结构中出现多量子点现象.     

带有InGaAs覆盖层的InAs量子点红外探测器材料的发光与光电响应

利用分子束外延技术(MBE),在GaAs(001)衬底上自组织生长了不同结构的InAs量子点样品,并制备了量子点红外探测器件。利用原子力显微镜(AFM)和光致发光(PL)光谱研究了量子点的表面结构、形貌和光学性质。渐变InGaAs层的插入有效地释放了InAs量子点所受的应力,抑制了量子点中In组分的偏析,提高了外延层的生长质量,降低了势垒高度,使InAs量子点荧光波长红移。伏安特性曲线和光电流(PC)谱结果表明,生长条件的优化提高了器件的红外响应,具有组分渐变的InGaAs层的探测器响应波长发生明显红移。     

InGaAs/GaAs应变量子阱的发光特性研究

利用低压金属有机化学气相沉积技术(LP-MOCVD)生长InGaAs/GaAs单量子阱(SQW),通过改变生长速率、优化生长温度和V/III比改善了量子阱样品的室温光致发光(PL)特性。测试结果表明,当生长温度为600℃、生长速率为1.15μm/h时,生长的量子阱PL谱较好,增加V/III比能够提高量子阱的发光强度。实验分析了在不同的In气相比条件下,生长速率对量子阱质量的影响,利用模型解释了高In气相比时,随着生长速率增加PL谱蓝移现象消失的原因。     

金辅助催化方法制备GaAs和GaAs/InGaAs纳米线结构的形貌表征及生长机理研究

利用金（Au）辅助催化的方法,通过金属有机化学气相沉积技术制备了GaAs纳米线及GaAs/InGaAs纳米线异质结构.通过对扫描电子显微镜（SEM）测试结果分析,发现温度会改变纳米线的生长机理,进而影响形貌特征.在GaAs纳米线的基础上制备了高质量的纳米线轴、径向异质结构,并对生长机理进行分析.SEM测试显示,GaAs/InGaAs异质结构呈现明显的“柱状”形貌与衬底垂直,InGaAs与GaAs段之间的界面清晰可见.通过X射线能谱对异质结样品进行了线分析,结果表明在GaAs/InGaAs轴向纳米线异质结构样品中,未发现明显的径向生长.从生长机理出发分析了在GaAs/InGaAs径向纳米线结构制备过程中伴随有少许轴向生长的现象.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.     

Direction-of-arrival estimation using matrix spatial prefiltering approach

An approach to direction-of-arrival （DOA） estimation for multiple narrowband farfield signals is proposed. The technique uses a novel matrix spatial prefiltering approach. Specifically, a matrix filter is designed to spatially filter the incoming data snapshots. The un-wanted components arriving from the stopband angular sectors are attenuated and the desired components from the angular sector of interest pass with minimal distortion. The matrix filter spatially filters the element-space data and the output reserves the element-space data property, which makes it very useful by passing sensor data through a spatial prefilter prior to applying many other array processors to attenuate interferences and improve system performance. Several examples of DOA estimation problem are presented to illustrate the performance of the proposed spatial prefiltering approach. Results of simulation and real data show that the pre-filter can efficiently attenuate the spatial interferences and significantly improve the estimation and resolution capability of DOA estimators at low signal-to-noise ratios for the sources located inside the passband sector. In addition, the use of spatial prefilter makes it possible to estimate DOAs for multiple sources more than the number of the elements of an array.     

Quantum efficiency calibration of opto-electronic detector by means of correlated photons method

A new calibration method of detectors can be realized by using correlated photons generated in spontaneous parametric down-conversion (SPDC) effect of nonlinear crystal.An absolute calibration system of detector quantum efficiency is performed.And its principle and experimental setup are introduced.A continuouswave (CW) ultraviolet (351 nm),diode-pumped,frequency-doubled,and solid-state laser is used to pump BBO crystal.The quantum efficiencies of the photomultiplier at 633,702,and 789 nm are measured respectively.The coincidence peaks are observed using coincidence circuit.Some measurement factors including the filter bandwidth of trigger channel,the detector position alignment and polarization of the pump light are analyzed.The uncertainties of this calibration method are also analyzed,and the relative uncertainties of total calibration are less than 5.8%.The accuracy of this method could be improved in the future.