基质固相分散-高效液相色谱法测定鲫鱼肌肉中残留的辛硫磷

建立了鲫鱼肌肉中残留的辛硫磷的基质固相分散-高效液相色谱-二极管阵列检测(MSPD-HPLC-DAD)的分析方法。通过优化样品处理条件,确定选取0.50 g鲫鱼肌肉样品与1.5 g弗罗里硅土、0.5 g无水硫酸钠混合研磨,并采用丙酮-正己烷溶液(体积比为40:60)为洗脱剂,洗脱剂用量为25 mL。优选的最佳色谱条件为：ODS色谱柱(250 mm×4.6 mm,5 μm),流动相为甲醇-水(体积比为50:50),流速0.6 mL/min,检测波长270 nm,进样量为20 μL。在上述条件下,辛硫磷质量浓度在0.01～10 mg/L范围内与响应信号呈良好的线性关系(r20.9994),检出限为3.3 μg/kg;相对标准偏差为1.1%～6.3%(n7);3个添加水平(0.05,0.1,1 mg/kg)下得到的回收率为88%～112%。该方法操作简单,耗时少,精密度高,符合农残分析的要求。     

高效液相色谱法同时检测8种喹诺酮类兽药残留量

建立了吡哌酸、氧氟沙星、环丙沙星、单诺沙星、恩诺沙星、沙拉沙星、(噁)喹酸和氟甲喹8种喹诺酮类兽药残留量的高效液相色谱-荧光检测方法. 方法的线性范围: 30～2000 μg/kg, 定量限为30 μg/kg, 检出限为5 μg/kg (吡哌酸为20 μg/kg). 该方法采用基质分散和微波萃取技术进行样品的前处理, 回收率为70.0%～99.5%, 相对标准偏差1.0%～8.5%. 并同固相萃取方法进行了比较, 分别使用了RPS、HLB、MAX 3种固相萃取柱, 其回收率均低于本法. 确立了以Aglient XDB-C18 (5 μm, 150 mm×4.6mm i.d.)色谱柱, H3PO4-纯水-三乙胺-乙腈(pH 3.0)为流动相的最佳色谱条件, 吡哌酸、氧氟沙星、环丙沙星、单诺沙星、恩诺沙星、沙拉沙星的检测波长为: 激发波长285 nm, 发射波长460 nm;(噁)喹酸和氟甲喹为: 激发波长325 nm, 发射波长365 nm. 方法可满足兽药残留检测要求.     

超高效液相色谱法检测化妆品中的12种磺胺抗生素

建立了采用超高效液相色谱(UPLC)-二极管阵列检测器（PDA）测定化妆品中12种常见的磺胺抗生素(磺胺、磺胺间甲氧嘧啶、磺胺醋酰、磺胺甲基异唑、磺胺嘧啶、磺胺二甲异唑、磺胺噻唑、磺胺二甲氧嘧啶、磺胺甲基嘧啶、磺胺喹啉、磺胺二甲嘧啶、磺胺硝苯)的方法。采用Acquity UPLCTM BEHC C18 色谱柱(50 mm×2.1 mm, 1.7 μm),流动相为乙腈/0.1%的甲酸水溶液,梯度洗脱。样品经提取、反萃取后,用UPLC-PDA进行分析检测,结合保留时间和紫外光谱进行定性分析,定量检测波长268 nm。12种磺胺的检出限(S/N=3)均为1 μg/g,定量下限(S/N=10)为2～3 μg/g,在1～25 mg/L(磺胺硝苯为0.5～12.5 mg/L)范围内,峰面积和质量浓度的线性关系良好(r>0.9997)。添加水平为40, 8 μg(磺胺硝苯为20, 4 μg)时,12种磺胺的平均回收率分别为86.8%～98.1%和80.1%～96.9%,相对标准偏差小于10%(n=6)。结果表明该方法简单,分离效果好,速度快,能够满足检测化妆品中12种常见的磺胺抗生素的需要。     

高效液相色谱-串联质谱法测定猪肉中泰拉霉素残留

建立了高效液相色谱-串联质谱(HPLC-MS/MS)测定猪肉样品中新型兽药泰拉霉素残留的方法.样品用V(甲醇): V(0.1% H3PO4)=70: 30混合溶液提取,经离心后用PCX固相萃取小柱净化, 以SymmetryC8色谱柱为分离柱,在串联质谱多反应监测(MRM)模式下检测,内标法定量.方法的线性范围为10～500 μg/kg,检出限为5.0 μg/kg,在3个浓度水平(10,20和50 μg/kg)进行添加实验,平均回收率为93.1%～105.5%; 批内相对标准偏差为1.5%～4.6%; 批间相对标准偏差为1.8 %～5.6%.     

UPLC-MS/MS和主成分分析法判别海洛因原产地

建立了超高效液相色谱-串联四极杆质谱仪(UPLC-MS-MS)在电喷雾离子源正离子(ESI+)和多反应监测(MRM)模式下定量测定海洛因中9种生物碱的方法,并采用主成分分析法建立数学模型,实现了快速区分"东南亚"和"西南亚"地区海洛因样品的目的。样品使用甲醇超声提取,ACQUITY UPLC BEH C18(100 mm×2.1 mm i.d.,1.7μm)色谱柱,流动相为pH 9.66的10 mmol/L的碳酸氢铵和乙腈,在梯度条件下分析。结果表明,在5～500μg/kg添加水平下回收率范围为88%～118%,相对标准偏差为1.7%～10%。9种生物碱的检出限(LOD,以信噪比(S/N)>3计)和定量限(LOQ,以S/N>10计)分别为0.03～1.67 mg/kg和0.10～5.51 mg/kg。本方法在11 min内即可对缴获海洛因样品中的9种生物碱进行定量分析,可用于海洛因原产地的快速判别。     

超高效液相色谱-串联质谱法测定乳制品中三聚氰胺的残留量

建立一种用超高效液相色谱-电喷雾质谱联用技术测定乳制品中三聚氰胺残留量的方法.样品经含5%乙酸铅的三氯乙酸溶液提取,离心分离后经PCX-C18混合填料固相萃取柱净化.色谱分离采用Agilent ZORBAX-CN柱(250 mm×4.6 mm i.d.,5 μm),以10 mmol/L V(乙酸铵)∶V(乙腈)＝10∶90混合溶液为流动相.采用电喷雾离子源,正离子多反应监测(MRM)模式检测.该方法在1～1000 ng/mL范围内线性关系良好.在添加水平为10,30,45 μg/kg时,回收率在78.5%～92.6%之间,相对标准偏差在3.5%～8.6%之间,检出限为10 μg/kg.该方法适合于乳制品中三聚氰胺残留量的检测.     

离子色谱法同时测定离子液体中六氟磷酸根及痕量杂阴离子

建立了一种同时测定离子液体中六氟磷酸根(PF~6)和痕量杂阴离子氟、氯、溴(F~,Cl~,Br~)的离子色谱方法(IC)。样品经溶解、稀释、过滤后用Dionex IonPac AS22分离柱(250 mm×4 mm)分离,淋洗液为碳酸盐-乙腈体系(体积比为70:30),流速1.0 mL/min,采用Dionex DS6电导检测器检测,外标法定量。F~,Cl~,Br~和PF~6的线性范围分别为0.5～50 μg/L、10～200 μg/L、10～200 μg/L和0.9～45 mg/L,线性相关系数分别为0.9999,0.9998,0.9999和0.9998,加标回收率为94.5%～100.5%,相对标准偏差为0.63%～1.03%,检出限(以信噪比为3计)分别为0.5 μg/L、2.0 μg/L、5.0 μg/L和0.9 mg/L。该方法用于离子液体中六氟磷酸根和痕量杂阴离子的同时测定,结果令人满意。     

超高效液相色谱-串联质谱法同时测定鱼制品中残留的7种性激素

以电喷雾离子源(ESI)为电离源,在正离子采集模式下建立了鱼制品中7种性激素（甲基炔诺酮、甲基睾酮、丙酸睾酮、醋酸甲羟孕酮、醋酸甲地孕酮、醋酸氯地孕酮、诺龙）的超高效液相色谱-质谱/质谱(UPLC-MS/MS)检测方法。样品被酶解后用甲醇提取,提取液经氯化锌(ZnCl2)去脂、LC-C18和LC-NH2固相萃取柱净化、Waters ACQUITYTM UPLC BEH-C18色谱柱(100 mm×2.1 mm, 1.7 μm)分离,在多反应监测模式下进行UPLC-MS/MS分析。7种性激素的方法检出限(S/N=3)为0.08～0.17 μg/kg,定量限(S/N=10)为0.24～0.58 μg/kg。考察了内标法和基质匹配外标法对7种性激素进行定量的回收率与精密度: 添加水平为1, 4 μg/kg时,以内标法定量,7种性激素的平均回收率为76%～118%,相对标准偏差（RSD）为5.0%～11.3%;以基质匹配外标法定量,7种性激素的平均回收率为66%～94%,RSD为4.5%～10.7%。该结果表明两种方法均能够满足鱼制品中7种性激素的多残留检测要求。应用建立的方法对市售脱脂大黄鱼及烤鱼片进行检测,未发现7种目标违禁性激素。     

液相色谱-电喷雾串联质谱法同时测定蜂胶保健品中的活性成分和降糖西药

采用超高效液相色谱-电喷雾串联四极杆质谱仪(UPLC-ESI-MS/MS)同时测定蜂胶保健品中14种活性成分和9种违禁降糖西药。蜂胶保健品样品用甲醇稀释,超声波提取,样品溶液经高速离心后过滤。使用ACQUITY UPLC C18反相柱(50 mm×2.1 mm,1.7μm);流动相为0.3%甲酸溶液和乙腈,在梯度条件下分析,目标分析物在多反应监测(MRM)模式下以保留时间和离子对(母离子和两个碎片离子)信息比较进行定性和定量分析。本方法的活性成分检出限(LOD)为0.7～42.0 mg/kg;定量限(LOQ)为2.2～140 mg/kg;活性成分的加标回收率为77.8%～113.6%;违禁降糖西药的LOD为0.1～0.9 mg/kg,LOQ为0.3～2.5 mg/kg;违禁降糖西药的平均回收率为79.3%～108.5%。本方法简便、有效、灵敏,为评价蜂胶保健品质量提供了新的检测方法。     

反相高效液相色法测定水产品中三聚氰胺

采用反相高效液相色谱法(RP-HPLC) 测定了水产品中的三聚氰胺. 色谱柱为Symmetry C18 (5 μm, 4.6 mm×250 mm), 流动相为含有0.01 mol/L庚烷磺酸钠和0.01 mol/L柠檬酸的乙腈(1+4)水溶液, 检测器为紫外检测器, 检测波长240 nm. 线性范围为1～50 μg/mL, 相关系数为0.9998, 最低检出限为0.24 μg/mL, 样品平均加标回收率为78.8%～96.1%, 相对标准偏差为3.7%～6.4%. 方法可用于水产品中三聚氰胺的测定.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.