Cu掺杂ZnO薄膜的光学性质

采用射频反应磁控溅射方法,在Si(100)和石英基片上使用双靶溅射的方法制备了Cu掺杂ZnO薄膜。利用X射线衍射、透射光谱和光致发光光谱分析了薄膜的晶体结构及光学性质,并与密度泛函理论计算的结果进行了对比。研究结果显示:Cu掺杂ZnO薄膜均具有高的c轴择优取向,无Cu及其氧化物相关相析出,掺杂对晶格参数的影响较小,与理论计算结果一致。Cu掺杂显著改变了ZnO薄膜在近紫外及可见光波段的吸收特性,其光学带隙随着Cu掺杂量的增加有所减小,带隙宽度的变化趋势与理论结果有着很好的一致性。Cu掺杂显著降低了ZnO薄膜的发光效率,具有明显的发光猝灭作用,但并不影响光致发光的发光峰位。说明Cu掺杂导致的吸收特性的改变可能与杂质能级有关,这与能带结构计算发现的Cu-3d电子态位于价带顶附近的禁带中是一致的。     

ZnO薄膜的光学性质研究

采用直流反应磁控溅射方法在玻璃基底上成功地淀积ｃ轴取向性好的ＺｎＯ薄膜。经过优化计算，获得并分析了不同氧分压下制备的ＺｎＯ薄膜的折射率ｎ和消光系数ｋ的数值；同时得到了吸收光学带隙Ｅｏｐｔ，用能带模型解释了Ｅｏｐｔ的变化规律。     

Ga-Ti共掺杂ZnO薄膜的制备及其光电性能

采用ZnO:Ga2O3:TiO2为靶材,在玻璃衬底上射频磁控溅射制备了多晶Ga-Ti共掺杂ZnO(GTZO)薄膜,通过XRD、四探针、透射光谱测试研究了生长温度对薄膜结构和光电性能的影响.结果表明:所制备的薄膜具有c轴择优取向,光学带隙均大于本征ZnO的禁带宽度.当生长温度为620K时GTZO薄膜的结晶质量最佳、电阻率最低、透射率最大、品质因数最高.     

氩气压强对射频磁控溅射ZnO：Al薄膜结构和性能的影响

以ZnO:Al2O3为靶材在石英玻璃衬底上射频磁控溅射制备多晶ZnO:Al(AZO)薄膜,通过XRD、AFM以及Hall效应、透射光谱等测试研究了RF溅射压强对薄膜结构、电学与光学性能的影响.分析表明:所制备的薄膜具有c轴择优取向,当压强为1.2Pa时薄膜的电阻率降至最低(2.7×10-3Ω·cm).薄膜在可见光区平均透射率高于90%,光学带隙均大于本征ZnO的禁带宽度.     

反应磁控溅射法制备的氟化类金刚石薄膜的XPS结构研究

采用射频反应磁控溅射法用高纯石墨作靶、三氟甲烷(CHF₃)和氩气(Ar)作源气体制 备了氟化类金刚石（FDLC）薄膜，通过XPS光谱结合拉曼光谱、红外透射光谱和紫外 可见光光谱研究了源气体流量比等工艺条件对薄膜中键结构、sp2/sp3杂化比以及光学带隙等性能的影响.结果表明在低功率(60W)、高气压(2.0Pa)和适当的流量比(Ar/CHF₃=2∶ 1)下利用射频反应磁控溅射法可制备出氟含量高且具有较宽光学带隙和超低介电常数的FDLC薄膜. 关键词： 反应磁控溅射 氟化类金刚石薄膜 红外透射光谱 XPS光谱     

溅射制备Ge,Nb共掺杂窄光学带隙和低电阻率的TiO2薄膜

采用射频磁控溅射技术制备了Ge,Nb共掺杂的锐钛矿结构TiO₂薄膜,详细探讨了薄膜的结构、电阻率及光学带隙等性质随Ge,Nb掺杂量、溅射功率和热处理温度等参数的变化,发现Ge,Nb共掺杂可以同时调节TiO₂薄膜的光学带隙和电阻率.体积分数约为6%Nb和20%Ge的共掺杂TiO₂薄膜电阻率由10⁴Ω/cm减小至10^-1Ω/cm,光学带隙由3.2 eV减小至1.9 eV.退火后掺杂TiO₂薄膜不仅显示更低的电阻率,还表现出更强的可见-红外光吸收.结果表明,改变Ge,Nb的掺杂量和退火条件能够制备出电阻率和带隙都可调的TiO₂薄膜.     

射频磁控溅射法制备N掺杂β-Ga2O3薄膜的光学特性

在不同氨分压比(0～30％)下,用射频磁控溅射法在玻璃和硅衬底上制备了N掺杂β-Ga2O3薄膜.研究了氨分压比和退火对薄膜光学和结构特性的影响.N掺杂β-Ga2O3薄膜的微结构、光学透过率、光学吸收和光学带隙随着氨分压比的增加发生了显著变化.观察到了绿光、蓝光和紫外发光带,并对每个发光带进行了讨论.     

含氮氟化类金刚石(FN-DLC)薄膜的研究：(Ⅱ)射频功率对薄膜光学带隙的影响

以CF₄,CH₄和N₂为源气体，采用射频等离子体增强化学气相沉积法，在不同射频功率下制备了含氮氟化类金刚石薄膜样品.原子力显微形貌显示，低功率下沉积样品表面致密均匀.拉曼及傅里叶变换红外光谱分析显示，随着射频功率的改变，薄膜的结构和组分也随之变化.紫外-可见光透射光谱证明薄膜具有紫外强吸收特性，通过计算得到其光学带隙在1.89—2.29 eV之间.结果表明，射频功率增加，薄膜内sp²C含量增加，或者说C=C交联相对浓度增加、F的相对浓度降低，导致薄膜内π-π^*带边态密度增大，光学带隙减小. 关键词： 含氮氟化类金刚石薄膜 射频功率 光学带隙     

基于透射光谱确定溅射Al2O3薄膜的光学（已撤稿）

基于反应磁控溅射Al₂O₃薄膜的紫外—可见—近红外透射实验光谱,采用Swanepoel方法结合Wemple-DiDomenico色散模型,方便地导出了Al₂O₃薄膜在200—1100 nm波长范围内的光学常数,包括折射率、色散常数、膜层厚度、吸收系数及能量带隙.研究发现反应磁控溅射Al₂O₃薄膜具有高折射率(1.556— 1.76,测试波长为550 nm)、低吸收和直接能量带隙(3.91—4.20 eV)等光学特性,而且其光学常数对薄膜制备过程中的重要工艺参数——膜层后处理温度表现出强烈的依赖性.此外,在膜层的弱吸收和中等吸收光谱区域内,计算得到的折射率色散曲线与分光光度法的测试结果基本符合,说明本实验中所建立的计算方法在确定反应磁控溅射Al₂O₃薄膜光学常数方面的可靠性. 关键词： 光学常数 Swanepoel方法 2O₃薄膜')" href="#">Al₂O₃薄膜 热处理     

反应磁控溅射ZnO/MgO多量子阱的光致荧光光谱分析

采用反应射频磁控溅射方法，在Si(001)基片上制备了具有高c轴择优取向的ZnO/MgO多量子阱.利用X射线反射、X射线衍射、电子探针，光致荧光光谱等表征技术，研究了ZnO/MgO多量子阱的结构、成份和光致荧光特性.研究结果表明，多量子阱的调制周期在1.85—22.3 nm之间，所制备的多量子阱具有量子限域效应，导致了室温光致荧光峰的蓝移，并观测到了量子隧穿效应引起的荧光效率下降.建立了基于多声子辅助激子复合跃迁理论的室温光致荧光光谱优化拟合方法，通过室温光致荧光光谱拟合发现，ZnO/MgO比ZnO/ZnMgO多量子阱具有更大的峰位蓝移，探讨了导致光致荧光光谱展宽的可能因素. 关键词： ZnO/MgO 多量子阱 磁控溅射 光致荧光 量子限域效应     

氧氩比对纳米ZnO薄膜蓝光发射光谱的影响

利用射频磁控溅射方法,在石英表面上制备了具有良好的c轴取向的纳米ZnO薄膜。室温下,在300 nm激发下,在450 nm附近观测到ZnO薄膜的蓝光发射谱(430~460 nm)。分析了气氛中氧气与氩气比对薄膜质量及蓝光发射光谱的影响,给出了纳米ZnO薄膜光致发光谱(PL)的积分强度和峰值强度与氧氩比关系。探讨了纳米ZnO薄膜的蓝光光谱的发射机制,初步证实了ZnO蓝光发射(2.88~2.69 eV)来自氧空位(VO)形成的浅施主能级上的电子至价带顶的跃迁。     

射频磁控溅射法制备ZnO薄膜的发光特性

利用射频磁控溅射法在硅衬底上制备出具有（002）择优取向的氧化锌薄膜，用波长为300nm的光激发，观察到在446nm处有一强的光致发光峰，它来自于氧空位浅施主能级上的电子到价带上的跃迁。并讨论了发光峰与氧压的关系以及退火对它的影响，且给出了解释。     

Deposition and properties of B-N codoped p-type ZnO thin films by RF magnetron sputtering

B-N codoped p-type ZnO thin films have been realized by radio frequency (rf) magnetron sputtering using a mixture of argon and oxygen as sputtering gas. Types of conduction and electrical properties in codoped ZnO films were found to be dependent on oxygen partial pressure ratios in the sputtering gas mixture. When oxygen partial pressure ratio was 70%, the codoped ZnO film showed p-type conduction and had the best electrical properties. Additionally, the p-ZnO/n-Si heterojunction showed a clear p-n diode characteristic. XRD results indicate that the B-N codoped ZnO film prepared in 70% oxygen partial pressure ratio has high crystal quality with (0 0 2) preferential orientation. Meanwhile, the B-N codoped ZnO film has high optical quality and displays the stronger near band edge (NBE) emission in the temperature-dependent photoluminescence spectrum, the acceptor energy level was estimated to be located at 125 meV above the valence band.     

ZnO薄膜的制备和发光特性的研究

用射频磁控溅射的方法在石英衬底上沉积了氧化锌薄膜，在室温下测量了样品的XRD曲线、吸收光谱以及光致发光光谱。探讨了气氛中氧气与氩气比对制备薄膜的影响，从XRD谱中可以看出，样品具有较好的结晶状态。另外，样品在紫外有较强的吸收，而其光致发光也是较强的紫外发射，这表明带间跃迁占了主导地位，以上结果说明：用溅射方法制备的ZnO薄膜结晶质量较好，富锌状态有所改善。     

溅射气氛对RF反应磁控溅射制备ZnO薄膜微结构及光致发光特性的影响

用射频反应磁控溅射法在不同溅射压强和氩氧比下制备了ZnO薄膜,通过X射线衍射(XRD)、扫描电镜(SEM)和光致发光(PL)谱等研究了溅射压强和氩氧比对ZnO薄膜结构和光学性质的影响。测量结果显示,所制备的ZnO薄膜为六角纤锌矿结构,具有沿c轴的择优取向;溅射压强P=0.6Pa,氩氧比Ar/O2=20/5.5sccm时,(002)晶面衍射峰强度和平均晶粒尺寸较大,(O02)XRD峰半峰全宽(FWHM)最小,光致发光紫外峰强度最强。     

磁控溅射制备ZnO薄膜的结构及发光特性研究

采用射频反应磁控溅射法在玻璃衬底上制备出具有c轴高择优取向的ZnO薄膜,利用X射线衍射、扫描探针显微镜及荧光分光光度法研究了生长温度对ZnO薄膜微观结构及光致发光特性的影响。结果表明,合适的衬底温度有利于提高ZnO薄膜的结晶质量;在室温下测量样品的光致发光谱(PL),观察到波长位于400 nm左右的紫光、446 nm左右的蓝色发光峰及502 nm左右微弱的绿光峰,随衬底温度升高,样品的PL谱中紫光及蓝光强度逐渐增大,同时,绿光峰的强度也表现出一定程度的增强。经分析得出紫光应是激子发光所致,而锌填隙则是引起蓝光发射的主要原因,502 nm左右的绿光峰应该是氧的深能级缺陷造成的。此外,还测量了样品的吸收谱,并结合样品吸收谱的拟合结果对光致发光机理的分析作了进一步的验证。     

Evaluation of acoustoelectric UV sensor according to ZnO thin film properties

This paper presents an improvement of the acoustoelectric effect by sensitivity and response of ultraviolet (UV) sensors by changing the argon/oxygen ratio. The acoustoelectric sensor is a delay-line type with a center frequency of 240.2625 MHz and fabricated on a piezoelectric substrate. Aluminum thin films were deposited as interdigitated transducers and patterned, and the ZnO thin film was deposited as a UV sensing layer by controlling the ratio of argon and oxygen with an RF magnetron sputtering. By increasing the oxygen partial pressure during ZnO deposition, the photoconductivity increased by 6.5 times, thereby increasing the frequency change related to the sensitivity of the sensor. The sensitivity to UV light was 110.4 Hz cm²/μW under an argon/oxygen ratio of 6:4, which is an increase of 5.1 times from 21.76 Hz cm²/μW obtained under a ratio of 10:2. In addition, the response and recovery times were improved by 2.85 times and 3.02 times, respectively.     

Effects of oxygen partial pressure on resistive switching characteristics of ZnO thin films by DC reactive magnetron sputtering

Cu/ZnO/n⁺-Si structures were prepared by magnetron sputtering of a layer of ZnO thin film onto heavily doped silicon substrate, followed by thermal evaporation of a thin layer of metallic Cu. The resistive switching characteristics of Cu/ZnO/n⁺-Si structures were investigated as a function of oxygen partial pressure during ZnO deposition. Reproducible resistive switching characteristics were observed in ZnO thin films deposited at 20%, 33% and 50% oxygen partial pressure ratios while ZnO thin film deposited at 10% oxygen partial pressure ratio did not show resistive switching behavior. The conduction mechanisms in high and low resistance states are dominated by space-charge-limited conduction and ohmic behavior respectively, which suggests that resistive switching behaviors in such structures are related to filament formation and rupture. It is also found that the reset current decreases as oxygen partial pressure increases, due to the variation of oxygen vacancy concentration in the ZnO thin films.     

Characterization of DC reactive magnetron sputtered NiO films using spectroscopic ellipsometry

Thin NiO films were deposited at 500 °C on n-type Si(1 1 1) by a DC reactive magnetron sputtering in a gas mixture of oxygen and argon. The ratio between the flow rates of oxygen and argon was respectively set at 1:4, 1:2, and 1:1. The dependence of structures and optical properties of NiO films were investigated using grazing incidence X-ray diffraction and spectroscopic ellipsometry in the spectral region of 1.5-5.0 eV. Ni-rich NiO films were obtained when the ratio between the flow rates of oxygen and argon was 1:4 and 1:2 in sputtering process. And when the ratio was 1:1, a relatively pure NiO film was formed. The partial pressure of oxygen could significantly influence the thickness and roughness of films. Refractive index n, extinction coefficient k, and direct gap energy and indirect gap energy of the NiO films were also subject to the influence of the partial pressure of oxygen.     

Optimization of parameters for deposition of Ga-doped ZnO films by DC reactive magnetron sputtering using Taguchi method

Ga-doped ZnO (ZnO:Ga) transparent conductive films were deposited on glass substrates by DC reactive magnetron sputtering. Taguchi method was used to find the optimal deposition parameters including oxygen partial pressure, argon partial pressure, substrate temperature, and sputtering power. By employing the analysis of variance, we found that the oxygen and argon partial pressures were the most influencing parameters on the electrical properties of ZnO:Ga films. Under the optimized deposition conditions, the ZnO:Ga films showed acceptable crystal quality, lowest electrical resistivity of 2.61 × 10⁻⁴ Ω cm, and high transmittance of 90% in the visible region.