Performance improvement of Ga N-based light-emitting diodes transferred from Si(111) substrate onto electroplating Cu submount with embedded wide p-electrodes

Crack-free Ga N/In Ga N multiple quantum wells(MQWs) light-emitting diodes(LEDs) are transferred from Si substrate onto electroplating Cu submount with embedded wide p-electrodes. The vertical-conducting n-side-up configuration of the LED is achieved by using the through-hole structure. The widened embedded p-electrode covers almost the whole transparent conductive layer(TCL), which could not be applied in the conventional p-side-up LEDs due to the electrodeshading effect. Therefore, the widened p-electrode improves the current spreading property and the uniformity of luminescence. The working voltage and series resistance are thereby reduced. The light output of embedded wide p-electrode LEDs on Cu is enhanced by 147% at a driving current of 350 m A, in comparison to conventional LEDs on Si.     

低温超薄高效Cu(In,Ga)Se2太阳电池的实现

衬底温度保持恒定, 在Se气氛下按照一定的元素配比顺序蒸发Ga, In, Cu制备厚度约为0.7 μrm的Cu(In_0.7Ga_0.3)Se₂ (CIGS)薄膜. 利用X射线衍射仪分析薄膜的晶体结构及物相组成, 扫描电子显微镜表征薄膜形貌及结晶质量, 二次离子质谱仪测试薄膜内部元素分布, 拉曼散射谱 分析薄膜表面构成, 带积分球附件的分光光度计测量薄膜光学性能. 研究发现在Ga-In-Se预制层内, In主要通过晶界扩散引起Ga/(Ga+In)分布均匀化. 衬底温度高于450 ℃时, 薄膜呈现单一的Cu(In_0.7Ga_0.3)Se₂相; 低于400℃, 薄膜存在严重的Ga的两相分离现象, 且高含Ga相主要存在于薄膜的上下表面; 低于300 ℃, 薄膜结晶质量进一步恶化. 薄膜表层的高含Ga相Cu(In_0.5Ga_0.5)Se₂以小晶粒形式均匀分布于薄膜表面, 增加了薄膜的粗糙度, 在电池内形成陷光结构, 提高了超薄电池对光的吸收. 加上带隙值较小的低含Ga相的存在, 使电池短路电流密度得到较大改善. 衬底温度在550 ℃–350 ℃变化时, 短路电流密度J_SC是影响超薄电池转换效率的主要因素; 而衬底温度T_sub低于300 ℃时, 开路电压V_OC和填充因子FF降低已成为电池性能减退的主要原因. T_sub为350 ℃时制备的0.7 μm左右的超薄CIGS电池转换效率达到了10.3%. 关键词： 2薄膜')" href="#">Cu(In,Ga)Se₂薄膜 衬底温度 超薄 太阳电池     

低温生长Cu(InGa)Se2薄膜吸收层的掺钠工艺研究

在柔性聚酰亚胺衬底上低温制备Cu(In,Ga)Se₂薄膜太阳能电池, Na的掺入会改善电池特性, 但不同的掺Na工艺对Cu(In,Ga)Se₂薄膜和器件特性的改善机理不同. 本实验通过对比前掺NaF和后掺NaF工艺发现, 在前掺Na工艺下, 由于Na始终存在于Cu(In,Ga)Se₂薄膜生长过程中, Na存在于多晶 Cu(In,Ga)Se₂ 薄膜晶界处, 起到了扩散势垒的作用, 导致晶粒细碎、加剧两相分离, 同时减小了施主缺陷的形成概率; 而在后掺Na工艺下, 掺入的Na对薄膜的结构及生长不产生影响, 仅仅起到了钝化施主缺陷、改善薄膜缺陷态的作用. 同时, 研究表明, 后掺Na工艺中, NaF必须依靠外界能量辅助才能扩散进Cu(In,Ga)Se₂内部, 实验结果证实, 只有衬底温度达到350 ℃以上时, 掺入的NaF才能较好地改善薄膜特性. 最终经掺Na工艺的优化, 得到低温工艺制备的柔性聚酰亚胺衬底器件效率达10.4%.     

La,V共掺杂的Bi_4Ti_3O_(12)铁电薄膜的溶胶-凝胶法制备及性能测试

采用溶胶-凝胶(sol-gel)工艺在Pt/TiO2/SiO2/p-Si(100)衬底上制备出Bi4Ti3O12(BIT)和Bi3.25La0.75Ti2.97V0.03O12(BLTV)铁电薄膜,研究了La,V共掺杂对BIT薄膜的晶体结构和电学性能的影响.BIT薄膜为c轴择优取向,BLTV薄膜为随机取向,拉曼光谱分析表明V掺杂降低了TiO6(或VO6)八面体的对称性,也增强了Ti—O键(或V—O键)杂化.BLTV薄膜的剩余极化Pr为25.4μC/cm2,远大于BIT薄膜的9.2μC/cm2,表现出良好的铁电性能.疲劳、漏电流测试显示BLTV薄膜具有优良的抗疲劳特性和漏电流特性,表明La,V共掺杂能有效地降低薄膜中的氧空位.     

Photocurrent oscillations in luminescent epitaxial thin films of ZnSe (Cu,Ga)

Photoluminescent epitaxial thin films of ZnSe (Cu, Ga), n-type, vacuum-deposited onto CaF₂ crystals, or air cleaved mica substrates, have been studied. At temperatures between 80 K and 220 K, slow photocurrent oscillations can be observed if ZnSe (Cu, Ga) thin films are illuminated with light (200 nm ? λ ? 530 nm) and an electric field is simultaneously applied, whose value is above a definite threshold. These oscillations, with amplitude and frequency varying as a function of temperature, applied electric field and light intensity, are attributed to moving high-field domains similar to those found by Boer and co-workers on CdS single crystals. Field quenching of luminescence is observed, which visualizes moving high-field domains. Anode-adjacent high-field domains occur at applied voltages above the range at which moving domains are observed and a simultaneous electroluminescence is initiated near the anode.     

准分子激光全固态脉冲电源设计与实验研究

针对脉冲能量5~8 mJ的ArF准分子激光器,设计了基于可控硅开关结合三级磁脉冲压缩开关的全固态脉冲电源,采用国产可控硅和磁开关材料,获得了上升时间约150 ns,电压10~14 kV,传递能量0.35~0.68 J的激励脉冲,并实现了对准分子激光器快放电激励。三级磁开关总效率35%,分析表明磁开关损耗较大主要原因为电容能量转移不充分、导线铜损及磁芯材料铁损较大,并提出了相应改进办法。     

Effect of AlGaN interlayer on luminous efficiency and reliability of GaN-based green LEDs on silicon substrate

The effect of AlGaN interlayer in quantum barrier on the electroluminescence characteristics of GaN-based green light emitting diodes(LEDs)grown on silicon substrate was investigated.The results show that AlGaN interlayer is beneficial to improve the luminous efficiency of LED devices and restrain the phase separation of In GaN.The former is ascribed to the inserted AlGaN layers can play a key role in determining the carrier distribution and screening dislocations in the active region,and the latter is attributed to the increased compressive stress in the quantum well.However,when the electrical stress aging tests were performed at a current density of 100 A/cm^2,LED devices with AlGaN interlayers are more likely to induce the generation/proliferation of defects in the active region under the effect of electrical stress,resulting in the reduced light output power at low current density.     

Cu(In,Ga)Se2 薄膜在共蒸发"三步法"中的相变过程

CIGS薄膜的结晶相是制备高质量薄膜的关键问题. 本文采用共蒸发"三步法"工艺沉积Gu(In, Ga)Se₂ (CIGS) 薄膜, 通过X射线衍射仪 (XRD) 和X射线荧光光谱仪 (XRF)、扫描电镜 (SEM) 结合的方法详细研究了"三步法"工艺的相变过程, 并制备出转换效率超过15% 的 CIGS 薄膜太阳电池. 关键词： CIGS薄膜 共蒸发三步法 相变过程     

UV-illuminated chemical bath deposition of CdS buffer layer for CIGSSe solar cells

In this paper, we compare the performance of Cu(In,Ga)(S,Se)₂ (CIGSSe) thin film solar cells with a CdS buffer layer grown by chemical bath deposition (CBD) with UV irradiation of 365 nm or 254 nm at an output power of 8 W. The effects of UV light irradiation on the CBD-CdS thin film deposition mechanism were investigated through chemical and electro-optical studies. UV light irradiation during the solution process promotes the hydrolysis of thiourea, thereby inhibiting the formation of the intermediate products being developed on the reaction pathways and decreasing the solution pH. Therefore, the efficiency of the CdS/CIGSSe solar cells was improved because of the increased elemental ratio of S/(S + O) in the CdS thin film. This very simple and effective approach can be used to control the S/O ratio of the CdS thin film fabricated by the CBD process without artificially controlling the process temperature, solution pH or concentration.     

金属有机物化学气相法制备YBCO超导薄膜研究

运用金属有机物化学气相沉积法(MOCVD),在LaAlO3(LAO)单晶上沉积YBa2Cu3O7-x(YBCO)超导薄膜。通过使用优化的进液装置,使金属有机源连续、稳定地输送至蒸发皿进行闪蒸。通过优化总气压、氧分压等生长条件,获得高质量的YBCO薄膜。在固定的温度条件下,调节反应总气压和氧分压,在总压为380Pa,氧分压为180Pa获得YBCO薄膜临界电流密度Jc=0.6MA/cm2。随着氧分压增大,YBCO薄膜产生a轴取向,(005)峰向左偏移,且薄膜中的Cu/Ba由1.0变化至1.63。在Cu/Ba=1.48时,YBCO薄膜结构与性能较优。     

Preparation of Cu（In,Ga）Se2 Thin Film Solar Cells by Selenization of Metallic Precursors in an Ar Atmosphere

Cu（In, Ga）Se2 thin films are deposited on Mo-coated glass substrates by Se vapour selenization of sputtered metallic precursors in the atmosphere of Ar gas flow under a pressure of about 10 Pa. The in situ heat treatment of as-grown precursor leads to the formation of a better alloy. During selenization, the growth of CuInSe2 phase preferably proceeds through Se-poor phases as CuSe and InSe at relatively low substrate temperature of 250℃, due to the absence of In2Se3 at intermediate stage at low reactor pressure. Subsequently, the Cu（In,Ga）Se2 phase is produced by the reactive diffusion of CuInSe2 with a Se-poor GaSe phase at high temperature of up to 560℃. The final film exhibits smooth surface and large grain size. The absorber is used to fabricate a glass/Mo/Cu（In, Ga）Se2/CdS/ZnO cell with the total-area efficiency of about 7%. The low open-circuit voltage value of the cell fabricated should result from the nonuniform distribution of In and Ga in the absorber, due to the diffusion-controlled reaction during the phase formation. The films, as well as devices, are characterized.     

Enhancements in specimen preparation of Cu(In,Ga)(S,Se)2 thin films

When producing slices from Cu(In,Ga)(S,Se)(2) thin films for solar cells by use of a focused ion beam (FIB), agglomerates form on the Cu(In,Ga)(S,Se)(2) surfaces, which deteriorate substantially the imaging and analysis in scanning electron microscopy. Similar problems are also experienced when depth-profiling Cu(In,Ga)(S,Se)(2) thin films by means of glow-discharge or secondary ion mass spectrometry. The present work shows that the agglomerates are composed of (mainly) Cu, and that their formation may be impeded considerably by either cooling of the sample or by use of reactive gases during the ion-beam sputtering. The introduction of XeF(2) during FIB slicing resulted in excellent images, in which the microstructures of most layers in the Cu(In,Ga)(S,Se)(2) thin film stack are visible, including the microstructure of the 20 nm thin MoSe(2) layer. Acquisition of high-quality two-dimensional and also three-dimensional electron backscatter diffraction data was possible. The present work gives a basis for enhanced SEM imaging and analysis not only in the case of Cu(In,Ga)(S,Se)(2) thin films but also when dealing with further material systems exhibiting similar formations of agglomerates.     

Stage2沉积速率对低温生长CIGS薄膜特性及器件的影响

研究了三步法第二步沉积速率对低温生长Cu(In,Ga)Se₂薄膜结构、 电学特性和器件特性的影响. 通过改变第二步沉积速率发现, 提高沉积速率可以显著促进薄膜晶粒生长, 提高晶粒紧凑程度降低晶界复合, 同时有效改善两相分离现象, 提高电池的开路电压和短路电流, 有助于Cu(In,Ga)Se₂电池光电转换效率的提高. 但同时研究表明, 随着第二步沉积速率的增加, 会促进暂态Cu_2-xSe晶粒的生长, 引起Cu(In,Ga)Se₂薄膜表面粗糙度增大, 并阻碍Na向Cu(In,Ga)Se₂薄膜表面的扩散, 造成施主缺陷钝化效应降低, 薄膜载流子浓度下降和电阻率升高, 且过高的沉积速率会引起电池内部复合增加并产生分流路径, 造成开路电压下降进而引起电池效率恶化. 最终, 通过最佳化第二步沉积速率, 在衬底温度为420℃时, 得到最高转换效率为11.24%的Cu(In,Ga)Se₂薄膜太阳电池.     

Influence of Cu electroplating solutions on boron carbon nitride (BCN) film

Cu electroplating is required for the fabrication of Cu/low-k interconnections. The permeation of a plating solution into low-k films during Cu electroplating is a serious challenge for 45-nm nodes and more complex devices. We investigated the influence of Cu electroplating solutions on boron carbon nitride (BCN) as a low-k film. After dipping it into a Cu electroplating solution that contained additives, the BCN film's hydrophilic surface changed to a hydrophobic surface, and the incorporation of water into the BCN film was suppressed by surfactant adsorption. Sulfuric residue was detected on the BCN sample by thermal desorption spectroscopy after treatment in the Cu electroplating solution with additives; however, it was found through electrical measurements that this solution did not affect the leakage current or the dielectric constant of the BCN film. We successfully fabricated an electroplating Cu layer on a BCN film with good adhesion, and we believe that this BCN film is a sufficiently useful material for Cu/BCN integration in LSI.     

Characterization of Cu(In,Ga)Se2 thin films prepared by evaporationfrom ternary compounds

Thin films of Cu(In,Ga)Se₂ were fabricated by evaporation from ternary CuGaSe₂ and CuInSe₂ compounds for photovoltaic device applications and their properties were investigated. From XRF analysis, the Cu:(In+Ga):Se atomic ratio in all thin films was approximately 1:1:2. The Ga/(In+Ga) atomic ratio in the thin films changed linearly from 0 to 1.0 with increasing the [CGS]/([CGS]+[CIS]) mole ratio in the evaporating materials. However, for thin films prepared at the [CGS]/([CGS]+[CIS]) mole ratio above 0.4, the composition by EPMA analysis was not consistent with that by XRF analysis. The result of EPMA analysis showed that the surface of a thin film was Cu-rich. XRD studies demonstrated that the thin films prepared at the [CGS]/([CGS]+[CIS]) mole ratio under 0.2 had a chalcopyrite Cu(In,Ga)Se₂ structure and the preferred orientation to the 112 plane. On the other hand, XRD patterns of the thin films produced at the [CGS]/([CGS]+[CIS]) mole ratio above 0.6 showed the diffraction lines from a chalcopyrite Cu(In,Ga)Se₂ and a foreign phase. The separation of a peak was observed near 2θ=27°, indicative the graded Ga concentration in Cu(In,Ga)Se₂ thin film.     

发光寿命在发光特性表征中的重要影响

吸收是发光的前提条件,吸收变了,发光的其他特性也就随之而变.但是发光寿命的长短又会反过来影响吸收的多少,这不仅存在于光致发光中,而且是一个普遍规律.从电场引起的场致发光中发现,在同一种材料中掺入两种发光寿命长短相差悬殊的发光中心Cu和Mn,利用激发电源频率的变化,明确地显示出发光寿命短的Cu的发光与发光寿命长的Mn的发光强度之比随频率的增加而增大,而且也显示了Cu的两种发光也有这种规律.实验结果说明,这种规律只取决于发光中心的寿命长短,而与激发方式及猝灭原因无关.     

衬底对Cu(In,Ga)Se2薄膜织构的影响

分别在苏打石灰玻璃、Mo箔、无择优取向的Mo薄膜以及(110)择优取向的Mo薄膜四种不同衬底上，采用共蒸发工艺沉积约2 μm厚的Cu(In,Ga)Se₂薄膜，用X射线衍射仪测量薄膜的织构，研究衬底对Cu(In,Ga)Se₂薄膜织构的影响.在以上四种衬底上沉积的Cu(In,Ga)Se₂薄膜的(112)衍射峰强度依次逐渐减弱，(220/204)衍射峰从无到有且强度逐渐增强.在苏打石灰玻璃和Mo箔衬底上的Cu(In,Ga)Se_{2关键词： 择优取向 Cu(In 2}薄膜')" href="#">Ga)Se₂薄膜 太阳电池     

Enhancing light extraction of GaN-based blue light-emitting diodes by a tuned nanopillar array

Surface patterning of p-GaN to improve the light extraction efficiency of GaN-based blue light-emitting diodes(LEDs) has been investigated. Periodic nanopillar arrays on p-GaN have been fabricated by polystyrene(PS) nanosphere lithography; the diameter of the nanopillars can be tuned to optimize the electrical and optical properties of the LEDs. The electroluminescence intensity of the nanopillar-patterned LEDs is better than that of conventional LEDs; the greatest enhancement increased the intensity by a factor of 1.41 at a 20 mA injection current. The enhancements can be explained by a model of bilayer film on a GaN substrate. This method may serve as a practical approach to improve the efficiency of light extraction from LEDs.     

金刚石薄膜电致发光现象的研究进展

阐明了金刚石薄膜电致发光研究的重要意义．综述了金刚石薄膜电致发光现象研究的进展情况，指出目前该方面研究中存在的问题，并提出了进一步提高金刚石薄膜蓝区电致发光强度的可能途径．     

电沉积Cu-In-Ga金属预制层的硒硫化研究

以H₂S气体作为硫源、固态蒸发硒蒸气作为硒源对电沉积Cu-In-Ga金属预制层进行硒硫化处理. 通过电沉积Cu-In-Ga金属预制层在不同衬底温度下硒化、硫化和硒硫化的对比实验,发现CuInS₂相和CuIn（S,Se）₂相优先生成,抑制了CuInSe₂相的生成,促使InSe相薄膜向内部扩散,减弱了薄膜两相分离现象. 采用先硒化后硒硫化处理工艺优化了Cu（In,Ga）（S,Se）₂薄膜的制备工艺,在250 ℃预硒化得到了开路电压为570 mV的太阳电池,在更高的预硒化温度得到了较大短路电流的太阳电池,最终优化得到了效率达到10.4%的电池器件. 关键词： 电化学沉积 Cu-In-Ga金属预制层 硒硫化处理 2薄膜')" href="#">Cu(In,Ga)(S,Se)₂薄膜