排序方式: 共有170条查询结果,搜索用时 15 毫秒
1.
The generation and measurement of complex ultraviolet laser pulse shapes is demonstrated in the SG-III laser facility. Relatively high contrast ratio of 300∶1 required by the physics experiment is achieved and successfully measured. Two continuous main shots validate the reproduction and the stability of the pulse shape, which provide solid foundation for precise physics experiment and laser power balance. 相似文献
2.
研究高功率激光装置光传输管道内部洁净度变化规律,分析其对内部重要光学元件光学性能的影响规律,提出污染控制措施。对光传输管道内部的气溶胶进行采样,并利用空气品质分析仪及扫描电镜对其进行分析,得到光传输管道内部洁净度变化规律和污染源;采用内部放置透射膜元件的方法,研究洁净度等级水平对透射膜的微观结构和透射率的影响,并利用"1-on-1"的测试方式进行透射膜元件的损伤阈值测试。研究结果表明:光传输管道内部的洁净度在激光辐照后迅速上升至万级水平,透射膜元件在此环境下其透过率严重下降,下降幅度为2.5%,且表面微观形貌发生变化。光学透射薄膜表面损伤阈值随表面污染水平呈现线性下降规律,最大下降幅度约为10%。污染监测和成分分析结果表明管道内部灰尘及杂散光或者鬼光束辐照金属产生的等离子体是管道内污染的主要源头,在此基础上提出了正压密封保持的技术手段确保内部光学表面洁净度水平,延长使用寿命。 相似文献
3.
4.
采用10.6 μupm 的 CO2激光, 对单次激光脉冲辐照修复熔石英存在的烧蚀采用大光斑钝化去除. 经过辐照修复的区域置于前表面测试初始损伤阈值, 结果表明调制造成的损伤得到了一定程度的抑制; 辐照区域置于后表面修复后 熔石英的初始损伤阈值超过了基底的初始损伤阈值. 实验观察到了应力分布外扩, 同时明显减弱. 对损伤增长的测试说明, 经过激光熔融辐照后的损伤点, 当应力释放以后, 损伤扩展初期表现出指数增长趋势, 后期随着辐照次数的增加, 损伤增长不再明显, 并且趋于恒定值. 相似文献
5.
Two localized CO2 laser treatment methods for mitigation of UV damage growth in fused silica 下载免费PDF全文
Two methods:high-power,short-time,single-shot irradiation(Method A) and low-power,long-time,multi-shot irradiation(Method B) are investigated to mitigate the UV damage growth in fused silica by using a 10.6-μm CO2 laser.To verify the mitigation effect of the two methods,the laser induced damage thresholds(LIDTs) of the mitigated sites are tested with a 355-nm,6.4-ns Nd:YAG laser,and the light modulation of the mitigation sites are tested with a 351-nm continuous Nd:YLF laser.The mitigated damaged sites treated with the two methods have almost the same LIDTs,which can recover to the level of pristine material.Compared with Method A,Method B produces mitigated sites with low crater depth and weak light modulation.In addition,there is no raised rim or re-deposited debris formed around the crater edge for Method B.Theoretical calculation is utilized to evaluate the central temperature of the CO2 laser beam irradiated zone and the radius of the crater.It is indicated that the calculated results are consistent with the experimental results. 相似文献
6.
基于熔石英材料对波长为10.6μm的CO2激光具有强吸收作用这一特点,提出采用CO2激光光栅式多次扫描修复熔石英光学元件表面密集分布的划痕和抛光点等缺陷的方法.实验结果表明,在合理的扫描参数下,元件表面的划痕和抛光点等缺陷可被充分地消除.损伤阈值测试结果表明,表面划痕和抛光点等缺陷被完全消除的元件的损伤阈值可回复到或超过基底的损伤阈值.同时结合有限元软件Ansys的模拟结果分析了CO2激光扫描修复及消除元件表面划痕和抛光点等缺陷的过程.本文为消除元件表面划痕和抛光点等缺陷提供了非常有意义的参考. 相似文献
7.
8.
9.
10.
针对高功率二极管重复率抽运的V型非稳腔Yb3+∶YAG激光头,提出了利用金刚石窗口冷却和直接水冷相结合的复合冷却设计.在YAG片的抽运面进行直接水冷,同时在激光提取面利用金刚石窗口冷却介质.金刚石优异的导热性能不仅能够有效地冷却激光介质,还能消除横向的温度梯度,解决了高功率激光器冷却和高功率抽运的矛盾.模拟结果表明对掺杂10 at %厚度为1.6 mm的Yb3+∶YAG片在抽运功率密度为20 kW/cm2,重复频率为10 Hz的条件下,要将最高温度控制在可接受的范围内(比如320 K),周围冷却水的对流换热系数约为4000 W/m2K. 相似文献