Stage2沉积速率对低温生长CIGS薄膜特性及器件的影响

研究了三步法第二步沉积速率对低温生长Cu(In,Ga)Se₂薄膜结构、 电学特性和器件特性的影响. 通过改变第二步沉积速率发现, 提高沉积速率可以显著促进薄膜晶粒生长, 提高晶粒紧凑程度降低晶界复合, 同时有效改善两相分离现象, 提高电池的开路电压和短路电流, 有助于Cu(In,Ga)Se₂电池光电转换效率的提高. 但同时研究表明, 随着第二步沉积速率的增加, 会促进暂态Cu_2-xSe晶粒的生长, 引起Cu(In,Ga)Se₂薄膜表面粗糙度增大, 并阻碍Na向Cu(In,Ga)Se₂薄膜表面的扩散, 造成施主缺陷钝化效应降低, 薄膜载流子浓度下降和电阻率升高, 且过高的沉积速率会引起电池内部复合增加并产生分流路径, 造成开路电压下降进而引起电池效率恶化. 最终, 通过最佳化第二步沉积速率, 在衬底温度为420℃时, 得到最高转换效率为11.24%的Cu(In,Ga)Se₂薄膜太阳电池.     

不同成分比例CIGS薄膜及太阳电池的快速退火

研究了110~180 ℃(2 min)下的快速热退火对Cu(In,Ga)Se2(CIGS)薄膜特性及CIGS太阳电池性能的影响.结果表明:对于不同成分比例的CIGS(正常、富Cu、高Ga)电池来说,150 ℃,2 min的快速退火最利于电池性能及二极管特性的增加.其中,退火对富Cu电池的开路电压Voc改善最大,这是因为快速热退火对消除部分CIGS薄膜中的CuSex有积极作用,从薄膜的电阻率有少量提高,器件的短路电流Jsc有少量下降可以得到验证;而对于高Ga电池来说,填充因子FF的改善最大,这是因为高Ga样品的缺陷较多,退火会消除薄膜内部的部分缺陷,从而薄膜的迁移率及Jsc都有所提高,使得FF有较大的增加.     

衬底对Cu(In,Ga)Se2薄膜织构的影响

分别在苏打石灰玻璃、Mo箔、无择优取向的Mo薄膜以及(110)择优取向的Mo薄膜四种不同衬底上,采用共蒸发工艺沉积约2μm厚的Cu(In,Ga)Se2薄膜,用X射线衍射仪测量薄膜的织构,研究衬底对Cu(In,Ga)Se2薄膜织构的影响.在以上四种衬底上沉积的Cu(In,Ga)Se2薄膜的(112)衍射峰强度依次逐渐减弱,(220/204)衍射峰从无到有且强度逐渐增强.在苏打石灰玻璃和Mo箔衬底上的Cu(In,Ga)Se2薄膜具有明显的(112)择优生长,而在(110)取向的Mo薄膜衬底上,Cu(In,Ga)Se2薄膜的织构为(220/204)取向.研究结果表明,只有(110)择优取向的Mo薄膜衬底对Cu(In,Ga)Se2薄膜(220/204)织构的形成有重要影响.     

衬底对Cu(In,Ga)Se2薄膜织构的影响

分别在苏打石灰玻璃、Mo箔、无择优取向的Mo薄膜以及(110)择优取向的Mo薄膜四种不同衬底上，采用共蒸发工艺沉积约2 μm厚的Cu(In,Ga)Se₂薄膜，用X射线衍射仪测量薄膜的织构，研究衬底对Cu(In,Ga)Se₂薄膜织构的影响.在以上四种衬底上沉积的Cu(In,Ga)Se₂薄膜的(112)衍射峰强度依次逐渐减弱，(220/204)衍射峰从无到有且强度逐渐增强.在苏打石灰玻璃和Mo箔衬底上的Cu(In,Ga)Se_{2关键词： 择优取向 Cu(In 2}薄膜')" href="#">Ga)Se₂薄膜 太阳电池     

不同成分比例CIGS薄膜及太阳电池的快速退火

研究了110~180 ℃（2 min）下的快速热退火对Cu(In,Ga)Se2(CIGS)薄膜特性及CIGS太阳电池性能的影响.结果表明：对于不同成分比例的CIGS（正常、富Cu、高Ga）电池来说,150 ℃,2 min的快速退火最利于电池性能及二极管特性的增加.其中,退火对富Cu电池的开路电压Voc改善最大,这是因为快速热退火对消除部分CIGS薄膜中的CuSex有积极作用,从薄膜的电阻率有少量提高,器件的短路电流Jsc有少量下降可以得到验证|而对于高Ga电池来说,填充因子FF的改善最大,这是因为高Ga样品的缺陷较多,退火会消除薄膜内部的部分缺陷,从而薄膜的迁移率及Jsc都有所提高,使得FF有较大的增加.     

Cu(In,Ga)Se2太阳能电池快速热退火效应

利用光致发光（PL）分析快速热退火对Cu(In,Ga)Se2 (CIGS)电池的影响,研究退火对薄膜缺陷的影响。Cu(In,Ga)Se2电池的PL谱中总共有 7个峰,即2个可见波段峰和5个红外波段峰。退火温度较低,可减少薄膜体内缺陷,提高载流子浓度,改善薄膜质量;退火温度过高,则会引起正常格点处元素扩散,元素化学计量比改变,体内缺陷增加,吸收层带隙降低,反而会对CIGS薄膜造成破坏。     

低温超薄高效Cu(In,Ga)Se2太阳电池的实现

衬底温度保持恒定, 在Se气氛下按照一定的元素配比顺序蒸发Ga, In, Cu制备厚度约为0.7 μrm的Cu(In_0.7Ga_0.3)Se₂ (CIGS)薄膜. 利用X射线衍射仪分析薄膜的晶体结构及物相组成, 扫描电子显微镜表征薄膜形貌及结晶质量, 二次离子质谱仪测试薄膜内部元素分布, 拉曼散射谱 分析薄膜表面构成, 带积分球附件的分光光度计测量薄膜光学性能. 研究发现在Ga-In-Se预制层内, In主要通过晶界扩散引起Ga/(Ga+In)分布均匀化. 衬底温度高于450 ℃时, 薄膜呈现单一的Cu(In_0.7Ga_0.3)Se₂相; 低于400℃, 薄膜存在严重的Ga的两相分离现象, 且高含Ga相主要存在于薄膜的上下表面; 低于300 ℃, 薄膜结晶质量进一步恶化. 薄膜表层的高含Ga相Cu(In_0.5Ga_0.5)Se₂以小晶粒形式均匀分布于薄膜表面, 增加了薄膜的粗糙度, 在电池内形成陷光结构, 提高了超薄电池对光的吸收. 加上带隙值较小的低含Ga相的存在, 使电池短路电流密度得到较大改善. 衬底温度在550 ℃–350 ℃变化时, 短路电流密度J_SC是影响超薄电池转换效率的主要因素; 而衬底温度T_sub低于300 ℃时, 开路电压V_OC和填充因子FF降低已成为电池性能减退的主要原因. T_sub为350 ℃时制备的0.7 μm左右的超薄CIGS电池转换效率达到了10.3%. 关键词： 2薄膜')" href="#">Cu(In,Ga)Se₂薄膜 衬底温度 超薄 太阳电池     

不同[Cu]/[In]比例的CuInS2薄膜的特性

采用连续离子层吸附与反应方法在玻璃基板上按照不同[Cu]/[In]的比例制备了CuInS₂薄膜,并在400 °C退火30 min. 对薄膜的晶体结构和晶粒尺寸用X射线衍射方法进行了表征,原子力显微镜测定薄膜的表面形貌. 研究不同的[Cu]/[In]比例对薄膜光学和电学性能的影响. 采用直流两探针法在300～470 °C测定CuInS₂薄膜的电阻率,随着[Cu]/[In]比例的增加,电阻率值越来越低. 溶液中[Cu]/[In]的比例明显影响CuInS₂薄膜的结构、电学和光学特性.     

N掺杂ZnO薄膜的荧光特性研究

以N₂为掺杂源,通过改变O₂∶N₂比,利用射频磁控溅射法在玻璃衬底上制备了具有[002]择优取向的N掺杂ZnO薄膜,研究了ZnO薄膜的光致发光谱随着N掺入量的不同而变化的规律.结果表明,薄膜主衍射峰为402 nm处的发光峰;由于N掺杂量的不同,有的薄膜在445 nm和524 nm处也有发光发存在,但随着薄膜N含量的不同,其发光峰强度明显不同,其峰位也发生了相应的红移或者蓝移.当O₂∶N₂为10∶15时,制备的薄膜N掺杂量最大,光学性能最好,此工艺为研究ZnO薄膜的缺陷类型及导电类型提供了重要的研究参考.     

直流三极溅射法制备CuInS2 薄膜

采用直流三极溅射装置制备获得了CuInS₂薄膜, 其中溅射靶采用一定面积比的[Cu]/[In]混合靶,反应气体采用CS₂气体. 本文中主要研究了0.02 Pa分压反应气体条件下不同面积比的[Cu]/[In]混合靶和沉积基板温度对CuInS₂薄膜结构和成分的影响, 其中CuInS₂薄膜制备所用时间为2 h生长的厚度为1—2 μm. 通过对CuInS₂薄膜的EPMA, X射线衍射测试分析表明, 最佳的CuInS₂薄膜可在面积比[Cu]/[In]混合靶为1.4:1和可控温度(150, 250和350 ℃)的条件下制备获得, 并且其结构被确认为黄铜矿结构. 通过实验结果计算出CuInS₂薄膜层有约为8.9%的C杂质含量.     

硒化前后电沉积贫铜和富铜的Cu(In1-xGax)Se2薄膜成分及结构的比较

采用电沉积法获得了接近化学计量比的贫铜和富铜的Cu（In_1-xGa_x）Se₂（CIGS）预置层,研究比较了两种预置层及其硒化处理后的成分和结构特性.得到了明确的实验证据证明,硒化后富铜薄膜中的Cu_xSe相会聚集凝结成结晶颗粒分散在表面.研究表明：在固态源硒化处理后,薄膜成分基本不变;当预置层中原子比Cu/（In+Ga）<11时,硒化后薄膜表面存在大量的裂纹;而当Cu/（In+Ga） >12时,可以消除裂纹的产生,形成等轴状小晶粒;富铜预置层硒化时蒸发沉积少量In,Ga和Se后,电池效率已达到68%;而贫铜预置层硒化后直接制备的电池效率大于2%,值得进一步深入研究. 关键词： 1-xGa_x）Se₂薄膜')" href="#">Cu（In_1-xGa_x）Se₂薄膜 电沉积 硒化处理 贫铜或富铜薄膜     

Inkjet printed Cu(In,Ga)S<Subscript>2</Subscript> nanoparticles for low-cost solar cells

Cu(In,Ga)Se₂ (CIGSe) thin film solar cells were fabricated by direct inkjet printing of Cu(In,Ga)S₂ (CIGS) nanoparticles followed by rapid thermal annealing under selenium vapor. Inkjet printing is a low-cost, low-waste, and flexible patterning method which can be used for deposition of solution-based or nanoparticle-based CIGS films with high throughput. XRD and Raman spectra indicate that no secondary phase is formed in the as-deposited CIGS film since quaternary chalcopyrite nanoparticles are used as the base solution for printing. Besides, CIGSe films with various Cu/(In + Ga) ratios could be obtained by finely tuning the composition of CIGS nanoparticles contained in the ink, which was found to strongly influence the devices performance and film morphology. To date, this is the first successful fabrication of a solar device by inkjet printing of CIGS nanoparticles.     

A new method of generating Ga slope in Cu(In,Ga)Se2 film by controlling Se content in a multi-stacked precursor

An appropriate Ga slope is required in Cu(In,Ga)Se₂ (CIGS) film to enhance the cell performance of CIGS thin-film solar cells. In the conventional three-stage-co-evaporation process, the Ga slope was obtained by controlling Ga/In flux during deposition process. However, in two-step process, where a precursor was deposited first and then annealed in a Se environment for mass production, the desirable Ga slope was not achievable with the Ga/In flux control. We observed that the Ga/(Ga + In) ratio was nearly flat in CIGS film for Se-rich precursor and the ratio was nearly zero at surface and very high on bottom side of CISG film for Se-deficient precursor. We were able to generate a CIGS film with a Ga non-zero Ga surface and desired slope in the bulk by devising a precursor with Se-rich layer on top and Se-deficient layer on bottom, resulting in the enhancement of Cell performance.     

Effect of post annealing on the characteristics of In2S3 buffer layer grown by chemical bath deposition on a CIGS substrate

In₂S₃ as an alternative Cd-free buffer in Cu(In,Ga)Se₂ (CIGS) solar cells was deposited on CIGS substrate by a chemical bath deposition and characterized after post annealing to optimize film properties for CIGS solar cells. A uniform and pinhole-free In₂S₃ film was deposited on a CIGS substrate by H₂O₂ treatment prior to chemical bath deposition. The In₂S₃ layer was an amorphous state due to the co-existence of In–S, In–O, and In–OH bonds. Annealing at 200 °C induced copper diffusion from CIGS into In₂S₃ layer and lowered the band gap from 3.3 to 1.9 eV, leading to phase change from amorphous state to crystalline state. The conduction band alignment at the In₂S₃/CIGS interface can be controlled by the post annealing. The shunt current through In₂S₃ film was prevented down to the thickness of 30 nm and a 1.15 eV shallow defect was eliminated by the annealing. The results indicated that post annealing in air is a critical to fabricate CIGS solar cells with a sub-30 nm CBD-In₂S₃ buffer layer.     

A comparative study of solution based CIGS thin film growth on different glass substrates

CuIn_xGa_1−xSe_yS_2−y (CIGS) thin films were synthesized on glass substrates by a paste coating of Cu, In, and Ga precursor solution with a three-step heat treatment process: oxidation, sulfurization, and selenization. In particular, morphological changes of CIGS films for each heat treatment step were investigated with respect to the kinds of glass substrates: bare, Mo-coated, and F-doped SnO₂ (FTO) soda-lime glasses. Very high quality CIGS film with large grains and low degree of porosity was obtained on the bare glass substrate. Similar morphology of CIGS film was also acquired on the Mo-coated glass except the formation of an undesired Mo oxide interfacial layer due to the partial oxidation of Mo layer during the first heat treatment under ambient conditions. On the other hand, CIGS film with much smaller grains and higher degree of porosity was gained when FTO glass was used as a substrate, resulting in slight solar to electricity conversion behavior (0.20%). Higher power conversion efficiency (1.32%) was attained by the device with the CIGS film grown on Mo-coated glass in spite of the presence of a Mo oxide impurity layer.     

Cu(In,Ga)Se2 薄膜在共蒸发"三步法"中的相变过程

CIGS薄膜的结晶相是制备高质量薄膜的关键问题. 本文采用共蒸发"三步法"工艺沉积Gu(In, Ga)Se₂ (CIGS) 薄膜, 通过X射线衍射仪 (XRD) 和X射线荧光光谱仪 (XRF)、扫描电镜 (SEM) 结合的方法详细研究了"三步法"工艺的相变过程, 并制备出转换效率超过15% 的 CIGS 薄膜太阳电池. 关键词： CIGS薄膜 共蒸发三步法 相变过程     

Thin Film Deposition Methods for CuInSe 2 Solar Cells

CuInSe₂ and its alloys with Ga and/or S are among the most promising absorber materials for thin film solar cells. CuInSe₂-based solar cells have shown long-term stability and the highest conversion efficiencies of all thin film solar cells, above 19%. Solar cells based on these materials are also very stable, thus allowing long operational lifetimes. The preparation of a thin film solar cell is a multistage process where every step affects the resulting cell performance and the production cost. CuInSe₂ and other Cu chalcopyrites can be prepared by a variety of methods, ranging from physical vapor deposition methods such as evaporation and sputtering to low-temperature liquid phase methods such as electrodeposition. The present review discusses first the concept and operation principle of thin film solar cells, as well as the most important thin film solar cell materials. Next, the properties of CuInSe₂ and related compounds, as well as features of solar cells made thereof are reviewed. The last part of the text deals with deposition methods used for the preparation of CuInSe₂ and Cu(In,Ga)Se₂ thin film absorbers and solar cells. Although the emphasis here is on absorber preparation methods, buffer and conducting oxide preparation are discussed as well.     

Ga梯度分布对Cu(In,Ga)Se_2薄膜及太阳电池的影响

传统制备Cu(In,Ga)Se2(CIGS)手段之一是共蒸发三步法,工艺中通过Cu,In,Ga,Se 4种元素相互扩散、作用形成抛物线形的Ga梯度分布.本文通过调整Ga源温度制备了Ga梯度分布不同的CIGS薄膜及电池.利用多种测试方法,研究了Ga梯度分布不同对CIGS薄膜表面及背面结构性质及电性质的影响,计算分析了表面导带失调值及背面电场对电池性能的影响,从而获得了合适的Ga梯度分布,提高了电池光谱相应,获得了较好的电池性能参数.