退火对非故意掺杂4H-SiC外延材料386 nm和388 nm发射峰的影响

10 K条件下,采用光致发光(PL)技术研究了不同退火处理后非故意掺杂4H-SiC外延材料的低温PL特性.结果发现,在370—400 nm范围内出现了三个发射峰,能量较高的峰约为3.26 eV,与4H-SiC材料的室温禁带宽度相当.波长约为386 nm和388 nm的两个发射峰分别位于~3.21 eV和~3.19 eV,与材料中的N杂质有关.当退火时间为30 min时,随退火温度的升高,386 nm和388 nm两个发射峰的PL强度先增加后减小,且退火温度为1573 K时,两个发射峰的PL强度均达到最大. 关键词： 光致发光 退火处理 能级 4H-SiC     

C(膜)/Si(SiO2)(纳米微粒)/C(膜) 的光致发光性质研究

用直流辉光溅射法结合真空镀膜法制备出了一种“多层三明治结构”的光致发光材料—C(膜 ) /Si(SiO2 ) (纳米微粒 ) /C(膜 )夹层膜 ,然后分别在 40 0、6 5 0和 75 0℃退火 1h .在波长为 2 5 0nm的紫外光激发下 ,刚制备出来未经退火处理的样品具有一个在 398nm (3.12eV)处的紫光宽带PL1峰 .在 6 5 0℃退火后 ,又出现了一个在 36 0nm (3.44eV)附近的PL2 峰 .PL1和PL2 峰形状和峰位与退火温度和激发波长无关 ,但强度却与退火温度和激发波长密切相关 .结合形态结构分析可知 ,紫光PL1峰可用量子限制 -发光中心 (QC LCs)模型进行解释 :即光激发发生在SiO2 微粒内部 ,而光发射源于SiO2 与Si界面上的缺陷中心 .紫外荧光PL2 峰则源自SiC内部的电子 空穴复合发光     

氢等离子体气氛中退火多孔硅的表面和光荧光特性

用电化学腐蚀法制备了多孔硅(PS),在氢等离子体气氛中不同温度下对多孔硅样品进行了退火处理,并进行了光致发光(PL)谱和原子力显微镜(AFM)表面形貌的测量。不同退火温度给PS表面形态带来较大变化,也影响了其PL谱特性。在退火的样品中观察到的PL谱高效蓝光和紫光谱带,我们认为主要源于量子限制发光峰和非平衡载流子被带隙中浅杂质能级所俘获而引起的辐射复合所产生的。在420—450℃退火处理的多孔硅的PL谱上观察到了一个未见诸于报道的紫光新谱带(3．24eV,382nm),其发光机理有待于进一步研究。     

ZnO/p-Si异质结的深能级及其对发光的影响

利用深能级瞬态谱(DLTS)和光致发光谱(PL),研究了ZnO/pSi异质结的两种不同温度(850℃,1000℃)退火下的深能级中心。发现850℃退火的样品存在3个明显的深中心,分别为E₁=E_v+0.21eV,E₂=E_v+0.44eV,E₃=E_v+071eV;而1000℃退火样品仅存在一个E₁=E_v+021eV的中心,且其隙态密度要比850℃退火的大。同时,测量了两个样品的PL谱。发现1000℃退火可消除一些影响发光强度的深能级,对改善晶格结构,提高样品的发光强度有利。     

射频磁控共溅射GaAs/SiO2纳米颗粒镶嵌薄膜的光学性质

应用射频磁控共溅射方法和真空退火方法制备了GaAsSiO2纳米颗粒镶嵌薄膜.X射线衍射实验结果表明,经高温退火的薄膜中形成了面心立方闪锌矿结构的GaAs纳米晶粒,晶粒平均直径为1.5—3.2nm.吸收光谱展示了由于强量子限域引起的1.5—2eV的吸收边蓝移.室温光致荧光(PL)光谱显示了电子重空穴激子与电子劈裂空穴激子的近紫外和紫外双PL谱峰以及深俘获态的PL谱峰.对实验吸收边蓝移量与有效质量模型的蓝移量的悬殊差别、俘获态PL谱的形成以及PL谱线的特征作了解释.应用激光Z扫描技术测量了退火温度为500℃的复合膜在非共振条件下的光学非线性,结果表明,复合膜的非线性折射率系数和非线性吸收系数都比块材GaAs相应的系数增大了5个数量级.光学非线性系数增大主要起因于强量子限域效应 关键词： 射频磁控共溅射 GaAsSiO2纳米颗粒镶嵌薄膜 光谱 激光Z扫描     

退火温度对低温生长MgxZn1－xO薄膜光学性质的影响

用射频磁控溅射法在80℃衬底温度下制备出Mg_xZn_1-xO(x=0.16)薄膜，用X射线衍射(XRD)、光致发光(PL)和透射谱研究了退火温度对Mg_xZn_1-xO薄膜结构和光学性质的影响.测量结果显示，Mg_xZn_1-xO薄膜为单相六角纤锌矿结构，并且具有沿c轴的择优取向；随着退火温度的升高，(002)XRD峰强度、平均晶粒尺寸和紫外PL峰强度增大，(002)XRD峰半高宽(F 关键词： xZn_1-xO薄膜')" href="#">Mg_xZn_1-xO薄膜 射频磁控溅射 退火     

富硅氮化硅薄膜的荧光发射

室温下在3．45eV的激光激发下,对950℃温度下淀积的LPCVD富硅的SiNx薄膜中,观测到5个高强度的可见荧光的发射。其峰位位置分别为2．7,2．69,2．4,2．3,2．1eV。通过TEM、IR、XPS等的分析研究表明,该样品为纳米硅镶嵌结构的a-SiNx：H复合膜,分析了其微结构的成因及其与膜内应力之间的相互关系。经过1000～1200℃快速退火(RTA)处理,原PL谱蓝移并只出现了峰位为3．0,2．8eV的两个紫蓝色荧光的发射,用能隙态模型对此结果做了初步的分析和讨论。认为薄膜中纳米硅团簇的密度、尺寸的变化和亚稳态缺陷态对其PL峰以及膜应力起着十分重要的作用。     

闪烁晶体碘化铯在紫外光和X射线激发下的发光特性

室温下掺铊碘化铯(CsI∶Tl)晶体的吸收谱在230~320 nm范围内有3个特征峰:310 nm(4 eV)、270nm(4.6 eV)和245 nm(5.1 eV)。采用这3种不同激发能量(对应不同激发机制)的近紫外(UV)光激发得到的荧光(PL)光谱相同。这些PL谱与钨(W)靶X射线激发的辐照致荧光(RL)谱也类似。经分峰计算,PL和RL均含有4种熟知的3.1 eV(400 nm)、2.55 eV(486 nm)、2.25 eV(550 nm)和2.1 eV(590 nm)发光组分,但RL中2.1 eV组分高于PL,同时2.55 eV组分又低于PL。分析认为,这一差异来自于X射线对晶体的辐照损伤Tl+Va+、Tl0Va+,相关的2.1 eV吸收峰与2.55 eV发光带重叠。结果表明:X射线比紫外光更易产生损伤从而影响晶体CsI∶Tl的发光特性。     

p型α-多孔SiC的光致发光光谱研究

用UV光照射和不用UV条件下形成的p型α-PSC的PL光谱，2.35eV，2.50eV和2.70eV及3.4eV附近的发射峰已被观察到.研究了不同的制备条件下形成的p型α-PSC的PL谱的稳定性和不同的能量的光激发引起PL谱的差别.结果表明，在电化学腐蚀过程中制备条件对PSC的PL谱有很大的影响，前者在低能区有较强的光发射而后者则在高能区有较强的光发射；前者的光谱稳定性较好而后者发射光谱强度则随时间的增加而减少.对产生这些差别的原因进行了深入讨论. 关键词：     

退火温度对低温生长MgxZn1-xO薄膜光学性质的影响

用射频磁控溅射法在80℃衬底温度下制备出MgxZn1-xO(x=0.16)薄膜,用X射线衍射(XRD)、光致发光(PL)和透射谱研究了退火温度对MgxZn1-xO薄膜结构和光学性质的影响.测量结果显示,MgxZn1-xO薄膜为单相六角纤锌矿结构,并且具有沿c轴的择优取向;随着退火温度的升高,(002)XRD峰强度、平均晶粒尺寸和紫外PL峰强度增大,(002)XRD峰半高宽(FWHM)减小.结果证明,用射频磁控溅射法通过适当控制退火温度可得到高质量MgxZn1-xO薄膜.     

Speckle characteristics of a broad-area VCSEL in the incoherent emission regime

We present a technique to reduce the speckle contrast of a NIR broad-area VCSEL based on the spatially incoherent emission regime that can be obtained when using the proper driving conditions. We evaluate the efficiency of this technique to reduce the speckle contrast by comparing it with the speckle characteristics in multimode emission under cw operation. Depending on the illumination setup, the incoherent emission regime can lead to a strongly reduced speckle contrast down to 1.3%. This is in agreement with estimates of the expected speckle contrast reduction when three contrast reducing effects are taken into account. These low contrast values make the investigated sources attractive for several applications that suffer from speckle noise.     

Structural characterization of ultrathin Cr and Sc films for soft X-ray mirrors

The structure of multilayers of ultrathin scandium (Sc) and chromium (Cr) films has been characterized by means of transmission electron microscopy (TEM). Face centered cubic Sc was found both in magnetron sputtered thin Sc layers on Si(0 0 1) and in Cr/Sc multilayers for soft X-ray mirrors. The single Sc and Cr layers are polycrystalline with randomly oriented grains, while Sc and Cr within the Cr/Sc multilayer show a strong [0 0 1] texture in the deposition direction. From high-resolution images the orientation-relationship at the Cr/Sc interfaces could be deduced as: Sc_[110]//Cr_[100] and Sc_[010]//Cr_[110], which was confirmed by image simulations.     

Optical transmission through an interface between subwavelength slits

This paper studies optical transmission through an interface between two slits with different widths in a sheet composed of an ideal conductor. Such a structure is of potential use in fabricating optical diode and may be the simplest one compared to other designs. Our calculations show that there is a critical wavelength. When the light wavelength is below the critical wavelength, the transmissivity is unidirectional. The expression of the stable transmissivity as a function of the ratio of the widths of the two slits was obtained analytically. Particularly, at the critical wavelength, the transmissivities are zero. This phenomenon has great potential for application in the manufacture of wavelength blockers.     

Grain boundary potential and charge density at grain boundaries of chemically prepared thin silver sulfide films

The grain boundary potential and interface state charge density at the grain boundaries of silver sulfide (Ag₂S) thin films prepared by chemical conversion of cadmium sulfide (CdS) films have been determined from the dc resistance of the material and are found to be sensitive to annealing. A reduction in the grain boundary potential and the grain boundary charge density of the film has been noticed when the source CdS film is annealed at different temperatures prior to chemical conversion. The variation in the grain boundary charge density of the grown Ag₂S film with source annealing temperature has been found to be similar to that of thin cadmium sulfide film, reported earlier. An additional low temperature heat treatment of the sample results in an enhancement in the charge density at the grain boundaries. The change in the silver vacancy and/or oxygen and sulfur content of the films as revealed from the energy dispersive spectra of the films suggests possible role of film composition on the grain boundary charge density.     

三螺旋DNA分子Poly(dT)·Poly(dA)·Poly(dT)碱基振动模式

利用晶格动力学方法计算了三螺旋 DNA分子 poly(d T)· poly(d A)· poly(d T)碱基振动模式 ,并根据势能分布矩阵对碱基振动模式进行了指定。计算的模式频率同拉曼光谱实验相符合     

XYZ particles at Belle

In this paper, I review recent progress in the study of the XYZ particles at Belle. I only focus on studies with charmonium and one or more light mesons in the final states. This covers the X(3872), X(3915),Y(4140), X(4350), and the charged Z states.     

Belle实验观测到新类粲偶素结构

利用在Υ(nS)(n=1,2,4,5)共振态及其附近采集的大量数据,Belle实验测量了末态中含两个矢量粒子的双光子过程γγ→J/ψ和ωJ/ψ.在这两个过程中,发现了两个窄共振结构X(4350)和X(3915).这两个新结构的性质目前尚不清楚,可能是普通粲偶素粒子,也可能是含一对粲夸克和一对轻夸克的四夸克态,或含一对粲夸克和一个激发胶子的混杂态,或是由其他未知的动力学原因造成的奇特结构.Belle同时发现在γγ→J/ψ过程中,不存在显著的Y(4140)的信号,实验结果与将Y(4140)解释为四夸克态的部分理论预期有较大差异.     

Effect of swift heavy ion irradiation on photoluminescence properties of ZnO/PMMA nanocomposite films

We report a study on the SHI induced modifications on structural and optical properties of ZnO/PMMA nanocomposite films. The ZnO nanoparticles were synthesized by the chemical route using 2-mercaptoethanol as a capping agent. The structure of ZnO nanoparticles was confirmed by XRD, SEM and TEM. These ZnO nanoparticles were dispersed in the PMMA matrix to form ZnO/PMMA nanocomposite films by the solution cast method. These ZnO/PMMA nanocomposite films were then irradiated by swift heavy ion irradiation (Ni⁸⁺ ion beam, 100 MeV) at a fluence of 1×10¹¹ ions/cm². The nanocomposite films were then characterized by XRD, UV-vis absorption spectroscopy and photoluminescence spectroscopy. As revealed from the absorption spectra, absorption edge is not changed by the irradiation but the optical absorption is increased. Enhanced green luminescence at about 527 nm and a less intense blue emission peak around 460 nm were observed after irradiation with respect to the pristine ZnO/PMMA nanocomposite film.     

The effect of phonon anisotropic scattering on the thermal conductivity of silicon thin films at 300K and 400K

Previous studies have shown that anisotropy in phonon transport exist because of the difference in phonon dispersion relation due to different lattice directions, as observed by a difference in in-plane and cross-plane thermal conductivities. Our current work intends to study the effect of anisotropy scattering on silicon thermal conductivity at 300 K and 400 K. We adopt the Henyey and Greenstein probability density function in our phonon Monte Carlo simulation to investigate the effect of highly forward and backward scattering events. The impact of applying the anisotropy scattering using this approach is discussed in detail. While the forward and backward scattering will increase and decrease thermal conductivity respectively, the extent of the effect is non-linear such that forward scattering has a more obvious effect on thermal conductivity than backward scattering.     

Effect of Ir(pq)2acac doping on CBP in phosphorescence organic light-emitting diodes

Doping is one of the most powerful methods amongst the various performance improvement ways. Doping affects the energy levels of the host layer by the energy level of the dopant. This allows the energy bandgap to be adjusted to a desired level and thus generates light corresponding to that energy level. Alternatively, it can act as an energy barrier between the interfaces to change the flow of carriers. In this study, the voltage dependences of undoped and doped devices were observed. Bis(2-phenylquinoline) iridium(III) (acetylacetonate) (Ir(pq)₂acac) was doped in 4,4′-N, N′-dicarbazole-biphenyl (CBP) as the emission layer. The light intensity changes with the doping concentration, and the efficiency was also studied. When a high voltage was applied, the effect of triplet-triplet annihilation (TTA) adversely affected the electron-hole recombination. We analyzed the optimal operating conditions and the effect of doping concentration on OLEDs.