利用InAs/GaAs数字合金超晶格改进InAs量子点有源区的结构设计

利用分子束外延技术,通过InAs/GaAs数字合金超晶格代替传统的直接生长InGaAs层的方式,在GaAs(100)衬底上生长了InAs量子点结构并成功制备了1.3μm InAs量子点激光器.通过原子力显微镜和光致荧光谱测试手段,对传统生长模式和数字合金超晶格生长模式的两种样品进行了表征,研究发现采用32周期InAs/GaAs数字合金超晶格样品的量子点密度非常高,发光性能良好.通过与常规生长方式所制备激光器的性能对比,发现采用InAs/GaAs数字合金超晶格生长InAs量子点的有源区也可以得到高质量的激光器.利用该方式生长的InAs量子点激光器的阈值电流为24 mA,相应的阈值电流密度仅为75 A/cm2,最高工作温度达到120℃.InAs/GaAs数字合金超晶格既可以保证生长过程中源炉的温度保持不变,还可以对InGaAs层的组分实现灵活调控.不需要改变生长速度,通过改变InAs/GaAs数字合金超晶格的周期数以及InAs层和GaAs层的厚度,便可以获得任意组分的InGaAs,从而得到不同发光波长的激光器.这种生长方式对量子点有源区的结构设计和外延生长提供了新思路.     

生长温度和结构参数对InGaAs／GaAs量子阱光学特性的影响

研究了不同生长温度下制备的In0.15Ga0.85As/GaAs应变量子阱的PL谱,结果表明,生长温度越高,In偏析和In-Ga互混越严重,同时,导致更多的In脱附,PL谱发光峰蓝移。对不同In含量的和不同InGaAs厚度的InGaAs/GaAs量子阱进行PL谱测试,分析表明In含量<0.2,生长温度低于560℃时,In含量和InGaAs层量子阱的厚度对In偏析、脱附和In-Ga互混基本没有影响。     

应力导致InAs/In0.15Ga0.85As量子点结构中 In0.15Ga0.85As阱层的合金分解效应研究

利用固源分子束外延技术,在In0.15Ga0.85As/GaAs量子阱生长了两个InAs/In0.15Ga0.85As量子点(DWELL)样品.通过改变其中一个InAs DWELL样品中的In0.15Ga0.85As阱层的厚度和生长温度,获得了量子点尺寸增大而且尺寸分布更均匀的结果.结合光致发光光谱(PL)和压电调制光谱(PzR)实验结果,发现该样品量子点的光学性质也同时得到了极大的优化.基于有效质量近似的数值计算结果表明:量子点后生长过程中应力导致In0.15Ga0.85As阱层合金分解机理是导致量子点尺寸和光学性质得到优化的主要原因.     

不同组分InxGa1-xAs(0≤x≤0.3)覆盖层对自组织InAs量子点的影响

研究了不同In组分的InxGa1-xAs(0≤x≤0.3)覆盖层对自组织InAs量子点的结构及发光特性的影响.透射电子显微镜和原子力显微镜表明,InAs量子点在InGaAs做盖层时所受应力较GaAs盖层时有所减小,并且x＝0.3时,InGaAs在InAs量子点上继续成岛.随x值的增大,量子点的光荧光峰红移,但随温度的变化发光峰峰位变化不明显.理论分析表明InAs量子点所受应力及其均匀性的变化分别是导致上述现象的主要原因.     

双层堆垛长波长InAs/GaAs量子点发光性质研究

研究了双层堆垛InAs/GaAs/InAs自组织量子点的生长和光致发光(PL)的物理性质。通过优化InAs淀积量、中间GaAs层厚度以及InAs量子点生长温度等生长条件,获得了室温光致发光1391～1438nm的高质量InAs量子点。研究发现对量子点GaAs间隔层实施原位退火、采用Sb辅助生长InGaAs盖层等方法可以增强高密度(2×1010 cm-2)InAs量子点的发光强度,减小光谱线宽,改善均匀性和红移发光波长。     

不同组分InxGa1-xAs(0≤x≤0.3)覆盖层对自组织InAs量子点的影响

研究了不同In组分的In_xGa_1-xAs(0≤x≤0.3)覆盖层对自组织InAs量子点的结构及发光特性的影响.透射电子显微镜和原子力显微镜表明,InAs量子点在InGaAs做盖层时所受应力较GaAs盖层时有所减小,并且x＝0.3时,InGaAs在InAs量子点上继续成岛.随x值的增大,量子点的光荧光峰红移,但随温度的变化发光峰峰位变化不明显.理论分析表明InAs量子点所受应力及其均匀性的变化分别是导致上述现象的主要原因. 关键词： 量子点 盖层 应力 红移     

液滴外延下生长参数对InAs纳米结构形貌的影响

利用液滴外延法在GaAs(001)衬底表面制备InAs量子点,通过控制变量分别研究沉积速率、沉积量对In液滴在GaAs表面生长过程中的影响.使用原子力显微镜(Atomic Force Microscope, AFM)表征InAs纳米结构形貌,得出结论：(1)沉积速率主要通过影响In液滴成核率来控制液滴的密度,即随着沉积速率的增大,In原子在衬底表面的成核率增加,InAs量子点密度增加,实验符合生长动力学经典成核理论.(2)沉积量的改变主要影响液滴的熟化过程,即随着沉积量的增大,可参与生长的活跃的In原子增加,促进了液滴熟化,使得扩散坍塌的原子数量增加,导致在InAs纳米结构中出现多量子点现象.     

带有InGaAs覆盖层的InAs量子点红外探测器材料的发光与光电响应

利用分子束外延技术(MBE),在GaAs(001)衬底上自组织生长了不同结构的InAs量子点样品,并制备了量子点红外探测器件。利用原子力显微镜(AFM)和光致发光(PL)光谱研究了量子点的表面结构、形貌和光学性质。渐变InGaAs层的插入有效地释放了InAs量子点所受的应力,抑制了量子点中In组分的偏析,提高了外延层的生长质量,降低了势垒高度,使InAs量子点荧光波长红移。伏安特性曲线和光电流(PC)谱结果表明,生长条件的优化提高了器件的红外响应,具有组分渐变的InGaAs层的探测器响应波长发生明显红移。     

InGaAs/GaAs应变量子阱的发光特性研究

利用低压金属有机化学气相沉积技术(LP-MOCVD)生长InGaAs/GaAs单量子阱(SQW),通过改变生长速率、优化生长温度和V/III比改善了量子阱样品的室温光致发光(PL)特性。测试结果表明,当生长温度为600℃、生长速率为1.15μm/h时,生长的量子阱PL谱较好,增加V/III比能够提高量子阱的发光强度。实验分析了在不同的In气相比条件下,生长速率对量子阱质量的影响,利用模型解释了高In气相比时,随着生长速率增加PL谱蓝移现象消失的原因。     

金辅助催化方法制备GaAs和GaAs/InGaAs纳米线结构的形貌表征及生长机理研究

利用金（Au）辅助催化的方法,通过金属有机化学气相沉积技术制备了GaAs纳米线及GaAs/InGaAs纳米线异质结构.通过对扫描电子显微镜（SEM）测试结果分析,发现温度会改变纳米线的生长机理,进而影响形貌特征.在GaAs纳米线的基础上制备了高质量的纳米线轴、径向异质结构,并对生长机理进行分析.SEM测试显示,GaAs/InGaAs异质结构呈现明显的“柱状”形貌与衬底垂直,InGaAs与GaAs段之间的界面清晰可见.通过X射线能谱对异质结样品进行了线分析,结果表明在GaAs/InGaAs轴向纳米线异质结构样品中,未发现明显的径向生长.从生长机理出发分析了在GaAs/InGaAs径向纳米线结构制备过程中伴随有少许轴向生长的现象.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.