InP阵列波导光栅的误差分析

在InP阵列波导光栅的制作过程中会引入不同的误差,从而影响器件的性能.为了最大限度地控制误差,提高半导体器件性能,本文采用传输函数法对InP基阵列波导光栅的系统误差和随机误差分别进行了分析.从系统误差的模拟结果中可以得到如下结论:深脊型波导的有效折射率n_c平均每偏移+0.000 1,中心波长偏移+0.05nm.相邻阵列波导长度差ΔL每偏移+0.01 μm,中心波长将偏移+0.44 nm.n_c和ΔL仅仅会影响到传输谱中心通道及其他各通道对应的波长,使得传输谱发生整体漂移,而信道间隔及串扰不会改变.罗兰圆半径R偏移不会影响器件的中心通道对应的波长,但会使其它通道对应的波长发生变化,最终使得信道间隔改变,R增加50 μm,信道间隔减小0.03 nm.从随机误差模拟结果中,得出:波导芯区折射率、上包层折射率、衬底折射率、波导宽度和波导芯层厚度的随机波动会对阵列波导光栅的串扰产生较大的影响.根据以上分析,可以通过控制不同参量来调节器件的中心波长以及信道间隔等来优化阵列波导光栅的光学性能.     

High efficiency,small size,and large bandwidth vertical interlayer waveguide coupler

Since the advent of three-dimensional photonic integrated circuits,the realization of efficient and compact optical interconnection between layers has become an important development direction.A vertical interlayer coupler between two silicon layers is presented in this paper.The coupling principle of the directional coupler is analyzed,and the traditional method of using a pair of vertically overlapping inverse taper structures is improved.For the coupling of two rectangular waveguide layers,a pair of nonlinear tapers with offset along the transmission direction is demonstrated.For the coupling of two ridge waveguide layers,a nonlinear taper in each layer is used to achieve high coupling efficiency.The simulation results show that the coupling efficiency of the two structures can reach more than 90%in a wavelength range from 1500 nm to 1650 nm.Moreover,the crosstalk is reduced to less than-50 d B by using multimode waveguides at intersections.The vertical interlayer coupler with a nonlinear taper is expected to realize the miniaturization and dense integration of photonic integrated chips.     

Derived Born cross sections of e~+e~- annihilation into open charm mesons from CLEO-c measurements

The exclusive Born cross sections of the production of D~0, D~+ and D_s~+ smesons in e~+e~- annihilation at 13 energy points between 3.970 and 4.260 Ge V are obtained by applying corrections for initial state radiation and vacuum polarization to the observed cross sections measured by the CLEO-c experiment. Both the statistical and the systematic uncertainties for the obtained Born cross sections are estimated.     

水热合成GdVO4:Eu3+晶体随pH值的形貌和性能演变

使用氧化钆、氧化铕和偏钒酸铵为原料,以DTAB为表面活性剂,在不同的反应溶液pH值条件下,采用水热合成法得到了从微米尺度到纳米尺度的一系列钒酸钆荧光粉。通过X射线衍射(XRD),场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)和荧光光谱(PL)等测试手段对不同形貌的样品的物相及微观形貌和发光性能进行表征。结果表明,在强酸环境下,晶体颗粒较大,为微米级,随着pH值的提升,晶体颗粒尺寸变小,进入纳米级,在pH为7,10时,分别得到50 nm以下的纳米晶片,且分散性良好。另外pH=7时观察到更为微小的小晶粒团,相比之下碱性环境下纳米晶片的结晶度较高。发光性能测试表明,样品发光性能随晶粒尺寸和结晶度变化显著。纳米尺度结晶良好的产品发光性能优异。     

Decay vertex reconstruction and 3-dimensional lifetime determination at BESⅢ

This paper focuses mainly on the vertex reconstruction of resonance particles with a relatively long lifetime such as Ks^0, A, as well as on lifetime measurements using a 3-dimensional fit. The kinematic constraints between the production and decay vertices and the decay vertex fitting algorithm based on the least squares method are both presented. Reconstruction efficiencies including experimental resolutions are discussed. The results and systematic errors are calculated based on a Monte Carlo simulation.     

Track reconstruction in the BESⅢ muon counter

The reconstruction algorithm for BESⅢ Muon Counter, MucRecAlg, is developed with the objectoriented language C＋＋ in BESⅢ offine software environment. MucRecAlg consists of the following functions：to find track seeds either from extrapolation of tracks in the main drift chamber or from the fired strips in muon counter, to select fired strips associated to the candidate tracks, to fit the candidate tracks with a linear or quadratic function and to calculate other parameters of the tracks for muon identification. Monte Carlo samples are generated to check the performance of the reconstruction package, such as reconstruction effciency, muon remaining rate and pion rejection rate, etc. The preliminary results show that the pion rejection rate is around 3%—4% while the muon remaining rate is better than 90% in 0.4—1.6 GeV/c momentum region, which meets the requirement as shown in the design report.     

4 × 20 GHz silica-based AWG hybrid integrated receiver optical sub-assemblies

Both the 4 × 20 GHz coarse wavelength division multiplexing and LAN-WDM receiver optical sub-assemblies(ROSAs) were developed. The ROSA package was hybrid integrated with a planar lightwave circuit arrayed waveguide grating(AWG) with 2% refractive index difference and a four-channel top-illuminated positive-intrinsicnegative photodetector(PD) array. The output waveguides of the AWG were designed in a multimode structure to provide flat-top optical spectra, and their end facet was angle-polished to form a total internal reflection interface to realize vertical coupling with a PD array. The maximum responsivity of ROSA was about 0.4 A/W, and its 3 dB bandwidth of frequency response was up to 20 GHz for each transmission lane. The hybrid integrated ROSA would be a cost-effective and easy-assembling solution for 100 Gb E data center interconnections.     

阵列波导光栅平坦化的研究

阵列波导光栅的平坦化在实际应用中有很重要的意义.本文系统地研究了阵列波导光栅的平坦化.在输入波导、输出波导、阵列波导输入端与输出端上分别引入了指数型锥形波导.通过改变锥形波导的形状和尺寸来实现平坦化的优化.本文首先从理论上论述了引入指数型锥形波导的输出光谱特性,给出了结构参量的关系表达式,阐明了输入波导处的锥形波导是影响输出光谱平坦化的主要因素,阵列波导和输出波导处的锥形波导对输出光谱的平坦化有一定的影响.其次采用数值模拟的方法模拟了输出光谱,优化了结构参量,总结出了指数型锥形波导对平坦化影响的趋势和规律.模拟结果显示,输出光谱1 dB带宽大于通道间隔的50%,插入损耗从5.2 dB减小到了4.0 dB,串扰小于-30 dB.最后,本文给出了实验结果,插入损耗减小了0.87 dB,串扰减小了3.67 dB,1 dB带宽增加0.1 nm,增加了54.7%.实验结果表明引入指数型锥形波导提高了阵列波导光栅器件的光谱性能.     

一道应用题的多种解法

看下面这道应用题: 如图1,一条河宽1km,两岸各有城市A和B,A与B的直线距离为4km,今需铺设一条电缆线连结A与B,已知地下电缆的修建费是2万元/km,水下电缆的修建费是