跑道型结构光子晶体波导定向耦合器

鉴于波导定向耦合器在集成光路以及光电集成方面的广泛应用,提出了一种基于光子晶体波导间高效耦合的光子晶体定向耦合器。通过主波导和耦合波导间的耦合,可以实现对波长为1 490 nm和1 550 nm电磁波的高效分光。在将器件长度控制在30 μm左右的同时,其总效率高达93.05%。另外,发现主波导和耦合波导间介质柱结构参数对电磁波的耦合周期有着极大的影响。并通过将介质柱沿z方向拉伸0.1a(a为晶格周期),设计了工作波长为1 530 nm和1 540 nm的光子晶体定向耦合器,器件长度仅为60 μm。通过拉伸介质柱的纵向长度,可以大幅减小耦合周期,这对缩小器件体积以及实现更为密集的波分复用有着重要的意义。     

Directly laser-written integrated photonics devices including diffractive optical elements

Femtosecond laser-written integrated devices involving Fresnel Zone Plates (FZPs) and waveguide arrays are demonstrated as built-in optical couplers. These structures were fabricated in borosilicate glass using a direct laser writing technique. The optical properties of these integrated photonic structures were investigated using CW lasers and high-resolution CCDs. For a single FZP coupled to a single waveguide, the overall coupling efficiency was 9%. A multiplexed optical coupler composed of three FZP layers was demonstrated to couple three waveguides simultaneously in a waveguide array. Structures of this type can be used as platforms for multichannel waveguide coupling elements or as microfluidic sensors that require higher light collecting efficiency.     

Efficient input and output fiber coupling to a photonic crystal waveguide

The efficiency of evanescent coupling between a silica optical fiber taper and a silicon photonic crystal waveguide is studied. A high-reflectivity mirror on the end of the photonic crystal waveguide is used to recollect, in the backward-propagating fiber mode, the optical power that is initially coupled into the photonic crystal waveguide. An outcoupled power in the backward-propagating fiber mode of 88% of the input power is measured, corresponding to a lower bound on the coupler efficiency of 94%.     

Compact and efficient coupler to interface hybrid dielectric-loaded plasmonic waveguide with silicon photonic slab waveguide

A coupler is proposed to interface a hybrid dielectric-loaded plasmonic waveguide (HDLPW) with a silicon photonic slab waveguide. The HDLPW is firstly designed and optimized to attain the best tradeoff between the mode confinement and the propagation distance. The designed coupler is inspired from the taper configuration and numerically modeled through finite-difference time-domain (FDTD) simulation. The results demonstrate that a high confinement and low loss of the energy is achieved from a silicon photonic slab waveguide into the dielectric slot of area 50×200 nm² in the HDLPW. The transmission attained through the coupler with a compact size of 400 nm is found to be as high as 80% (1 dB). Further, the planar nature of taper configuration makes the coupler easy to fabricate using the state-of-the-art CMOS facilities. The proposed coupler is useful in enabling the integration between photonic and hybrid plasmonic waveguides and thus realizing on-chip hybrid integrated circuits.     

Asymmetric plasmonic-dielectric coupler with short coupling length, high extinction ratio, and low insertion loss

Asymmetric directional coupling between a hybrid plasmonic waveguide with subwavelength field confinement and a conventional dielectric waveguide is investigated. The proposed hybrid coupler features short coupling length, high coupling efficiency, high extinction ratio, and low insertion loss; it can also be integrated into a silicon-based platform. This coupler can be potentially adopted for signal routing between plasmonic waveguides and dielectric waveguides in photonic integrated circuits. Furthermore, it can be exploited to efficiently excite hybrid plasmonic modes with conventional dielectric modes.     

High-efficiency optical coupling to planar photodiode using metal reflector loaded waveguide grating coupler

For the realization of optoelectronic integrated circuits, it is required to incident light perpendicularly to a planar Si photodiode. We propose a high-efficient vertical optical coupler using an amorphous Si optical waveguide grating coupler with top reflector, which is transparent at 850 nm wavelength range. The optical waveguide (width of 300 nm $\times $ height of 100 nm) coupler is analyzed by using finite element method. The coupling efficiency of 80 % is calculated at the grating period of 380 nm, the duty ratio of 0.75 and the depth of 35–65 nm with top metal reflector.     

Ultra-low-loss inverted taper coupler for silicon-on-insulator ridge waveguide

An ultra-low-loss coupler for interfacing a silicon-on-insulator ridge waveguide and a single-mode fiber in both polarizations is presented. The inverted taper coupler, embedded in a polymer waveguide, is optimized for both the transverse-magnetic and transverse-electric modes through tapering the width of the silicon-on-insulator waveguide from 450 nm down to less than 15 nm applying a thermal oxidation process. Two inverted taper couplers are integrated with a 3-mm long silicon-on-insulator ridge waveguide in the fabricated sample. The measured coupling losses of the inverted taper coupler for transverse-magnetic and transverse-electric modes are ∼ 0.36 dB and ∼ 0.66 dB per connection, respectively.     

Polymer-waveguide-based vertical coupler

A 2 × 2 polymer-waveguide-based vertical coupler was designed and fabricated. The relationships between the coupling efficiency and the key optical design parameters of vertical coupler (such as the crossing angle, gap thickness between two waveguide layers and the waveguide dimensions) were investigated by using beam propagation method. Based on these simulations, a fully polymer vertical coupler was demonstrated.     

Vertical coupling characteristics between hybrid plasmonic slot waveguide and Si waveguide

For development of complementary metal–oxide–semiconductor (CMOS)-compatible integrated optical circuits, vertical directional coupling between a hybrid plasmonic slot waveguide and a Si waveguide is theoretically investigated in detail. To determine the vertical separation gap and efficient coupling length, we investigate the characteristics of the even and odd supermodes at a wavelength of 1.55 μm. The vertical coupler transfers 90% of the power carried by the Si waveguide to the hybrid plasmonic slot waveguide after normalizing to reference waveguides when the gap is 60 nm and the coupling length is 2.6 μm. Because of the lossy hybrid guided mode in the plasmonic waveguide, the transmitted power exhibits damped sinusoidal behavior depending on the overlapping length. The proposed vertical coupler shows more efficient light coupling between a dielectric and plasmonic waveguide in comparison to the other types of hybrid coupler, and can be exploited further for on-chip integrated opto-electronic circuits.     

用级联缓变结构实现光子晶体波导和传统波导的耦合

为了提高光子晶体波导与传统介质波导的耦合效率,设计了级联缓变结构.先将传统介质波导中的光耦合进尺寸相当的光子晶体W5波导中,然后W5波导中的光被耦合进尺寸较小些的W3波导中,最后光被耦合进尺寸最小的W1波导.各级波导之间由半径逐渐增大的空气孔连接,空气孔半径逐渐变化相当于波导有效折射率在变化,所以各级波导可以看作是被折射率缓变结构连接起来.由于折射率的缓变,使得光从前一级波导耦合进相邻的后一级波导时反射很小,从而能有效地提高耦合效率.数值计算表明,在光子晶体禁带范围内,除了波导有限长度和波导微小禁带造成的微小不通带外,耦合系数一般能达80%左右,最高可达到95%.     

Photonic crystal tapers for ultracompact mode conversion

We have studied the coupling of a classic ridge waveguide with a two-dimensional photonic crystal (PC) waveguide, using finite-difference time-domain calculations. The ridge waveguide exhibits only a weak refractive-index confinement of light, as it is commonly used in buried-heterostructure or ridge-waveguide lasers. The light is coupled to a PC waveguide that consists of one missing row along the ?K direction in a triangular lattice of air cylinders in AlGaAs. We compare various designs for PC tapers with that of a classic taper and for butt coupling. The calculation yields high coupling efficiency that exceeds 80% for a 2.5-microm-long PC taper. In addition, the dependence of the efficiency on the PC air-fill factor and on alignment tolerances is analyzed.     

Parallel microgenetic algorithm design for photonic crystal and waveguide structures

We have developed a powerful parallel genetic algorithm design tool for photonic crystal and waveguide structures. The tool employs a small-population-size genetic algorithm (microgenetic algorithm) for global optimization and a two-dimensional finite-difference time-domain method to rigorously design and optimize the performance of photonic devices. We discuss the implementation and performance of this design tool. We demonstrate its application to two photonic devices, a defect taper coupler to connect conventional waveguides and photonic crystal waveguides, and a sharp 90 degrees waveguide bend for low index contrast waveguides.     

A very short vertical directional coupler with polarization-insensitive high extinction ratios

We propose a very short vertical directional coupler with polarization-insensitive high extinction ratios. The structure of the coupler has two deep-ridge waveguide structures in the upper and lower parts which can be implemented using a double-sided wafer process. The coupling length and extinction ratios of the vertical directional coupler with symmetric structures decrease as the thicknesses of the inner cladding layer and core layer decrease. The extinction ratio is improved using a slight asymmetry in the refractive indices of two core layers. As the thicknesses of the inner cladding layer and core layer decrease, the length of the vertical directional coupler for extinction ratios greater than 30 dB of both TE and TM modes decreases. A vertical directional coupler with a very short length less than 100 μm and polarization-insensitive high extinction ratios greater than 30 dB can be implemented using the structure proposed in this paper.     

High efficiency grating coupler between silicon-on-insulator waveguides and perfectly vertical optical fibers

A high-efficiency waveguide-to-fiber grating coupler for silicon-on-insulator waveguides was designed. Perfectly vertical fiber coupling is achieved by using an asymmetric grating structure to suppress the second-order Bragg reflection from the grating. The ability to use a perfectly vertical positioned optical fiber simplifies the packaging of the photonic integrated circuit. A coupling efficiency of 80% at a wavelength of 1.55 microm is obtained.     

Two-dimensional photonic crystal couplers for unidirectional light output

We investigate the use of two-dimensional photonic crystal slabs to improve the directionality of output coupling from planar waveguides and distributed-feedback lasers. We present the theory underlying the operation of such structures and design criteria for emission in desired directions. As an example, we demonstrate a vertical coupler that is integrated with an organic distributed-feedback laser, use computer simulations to find its coupling constant and efficiency, and then discuss its feasibility.     

Numerical characterization of nanopillar photonic crystal waveguides and directional couplers

We numerically characterize a novel type of a photonic crystal waveguide, which consists of several rows of periodically arranged dielectric cylinders. In such a nanopillar photonic crystal waveguide, light confinement is due to the total internal reflection. A nanopillar waveguide is a multimode waveguide, where the number of modes is equal to the number of rows building the waveguide. The strong coupling between individual waveguides leads to the proposal of an ultrashort directional coupler based on nanopillar waveguides. We present a systematic analysis of the dispersion and transmission efficiency of nanopillar photonic crystal waveguides and directional couplers. Plane wave expansion and finite difference time domain methods were used to characterize numerically nanopillar photonic crystal structures both in two- and three-dimensional spaces.     

Wide, tunable band rejection filter based on micro-optical waveguide on microactuating platform covering O, E, S, C, L, and U bands

An ultrawide, tunable band rejection filter was experimentally demonstrated operating from 1060 to 1670 nm seamlessly covering all communication bands (O, E, S, C, L, and U bands). The device consists of a micro-optical waveguide made from fused taper fiber coupler mounted over a microactuating platform that systematically applies a highly localized torsional stress over the coupling region. High-band rejection efficiency of 20-30 dB and very low insertion loss of 0.2 dB were experimentally achieved over the whole operating spectral range.     

光子晶体平面波导与脊波导高效耦合技术的研究

利用一维变周期谐振腔阵列和非线性缓变边界，可以实现光波从脊波导到光子晶体平面波导 （PCW）的高效耦合.基于平面波展开法（PWE）和时域有限差分法（FDTD），深入分析和讨 论了普通脊波导、2D-PCW结构和本征模以及工作模式、缓变边界形状等对耦合效率的影响， 从而得出光波从脊波导到2D-PCW、再返回脊波导的统一图景.指出考虑模式转换和采用缓变 边界条件可以极大提高PCW与脊波导间的耦合效率.对PC-PW边界采用线性和非线性缓变结构 进行了仿真，讨论了边界缓变程度对耦合效率的影响.结果表明，采用模式耦合和PC-PW余弦 缓变边界时的耦合效率在较宽的带宽内超过了95%. 关键词： 光子晶体波导 脊波导 PWE FDTD 耦合边界     

Monolithically integrated photonic-crystal devices with photodiodes

In this paper, we demonstrate the monolithic integration of a conventional waveguide, a photonic crystal demultiplexer, a photonic crystal taper coupler, photonic crystal waveguides, and photodiodes in InGaAsP-based material to form a planar nano-optics system. Photonic crystal demultiplexers consist of hexagonally arranged air holes. Finite-difference time-domain method is implemented to investigate the performance of the demultiplexer. The system is fabricated using e-beam lithography and conventional photolithography. The input light at wavelengths of 1530 and 1550 nm can be separated using the demultiplexing system. These can then be detected by photodiodes that exhibit a wide-bandwidth performance of 22 GHz.     

基于光子集成芯片的可穿戴光纤光栅解调研究

为了实现光纤光栅传感器在可穿戴系统中的应用,提出了一种基于硅基光子集成芯片的可穿戴光纤光栅传感解调系统。基于比利时iSiPP50G工艺的光子集成芯片由4×1长波长VCSEL阵列、1×8阵列波导光栅、2×2 MMI耦合器、4×1光纤光栅耦合器阵列、Ge-on-Si波导光电探测器、直波导和弯曲波导等组成。在完成对VCSEL光源金线键合和光子集成芯片光纤耦合封装的基础上,设计了手环式解调电路,对人体温度和心音信号进行了实时测量。实验结果表明:解调系统的动态波长检测范围为1 540 nm～1 560 nm,波长分辨率为0.08 pm,解调精度为5 pm,温度监测范围为35℃～42℃,误差为±0.1℃;可检测50 Hz～100 Hz频率范围内的心音信号,可识别出第一心音和第二心音,并计算出心动周期、心率、第一心音时限、第二心音时限和心力等特征参数。