SnO2微纳米材料的合成及其生长机理研究

利用简单的化学气相沉积法,以Sn粉为源材料合成不同形貌的一维SnO2纳米棒、纳米线和纳米花等纳米结构,并通过减小载气中的氧含量获得新颖的SnO2亚微米环状结构.通过调节Sn粉的量和载气中的氧含量、升温速率等试验条件,有效实现SnO2一维纳米结构的控制生长.采用扫描电子显微镜、能谱仪和X射线衍射仪表征产物形貌、成分和物相结构,并探讨了SnO2微纳米材料的生长机理.     

衬底位置对化学气相沉积法制备的磷掺杂p型ZnO纳米材料形貌和特性的影响

采用化学气相沉积方法,在无催化剂的条件下,通过改变衬底位置在Si(100)衬底上制备出了高取向的磷掺杂ZnO纳米线和纳米钉.测试结果表明,当衬底位于反应源上方1.5 cm处时,所制备的样品为钉状结构,而当衬底位于反应源下方1 cm处时样品为线状结构.对不同形貌磷掺杂ZnO纳米结构的生长机理进行了研究.此外,在ZnO纳米结构的低温光致发光谱中观测到了一系列与磷掺杂相关的受主发光峰.还对磷掺杂ZnO纳米结构/n-Si异质结I-V曲线进行了测试,结果表明,该器件具有良好的整流特性,纳米线和纳米钉异质结器件的开启电压分别为4.8和3.2 V.     

衬底对化学气相沉积法制备氧化硅纳米线的影响

通过化学气相沉积法在不同衬底上制备了大量的氧化硅纳米线.选用衬底为Si片、带有约100nm厚SiO2氧化层Si片和石英片.利用场发射扫描电子显微镜(SEM)和透射电镜(TEM，配备有能谱仪)对样品的表面形貌、结构和成分进行研究.结果表明：这些纳米线都为非晶态，但在不同衬底上生长的纳米线形貌、尺寸和化学成分不同.讨论了各种衬底对不同特征氧化硅纳米线生长的影响. 关键词： 化学气相沉积 纳米线 纳米颗粒     

化学气相沉积法制备GaN纳米结构设计性实验

在无催化剂辅助条件下,采用化学气相沉积法生长了GaN纳米线.通过调整衬底、NH3气流、生长时间等,实现了半导体GaN纳米线的生长以及形貌调控.用X射线衍射仪和扫描电子显微镜对产物的物相及形貌进行了表征.获得了合成GaN纳米线的优化条件.     

SnO2微纳米材料的合成及其生长机理研究

利用简单的化学气相沉积法,以Sn粉为源材料合成不同形貌的一维SnO₂纳米棒、纳米线和纳米花等纳米结构,并通过减小载气中的氧含量获得新颖的SnO₂亚微米环状结构.通过调节Sn粉的量和载气中的氧含量、升温速率等试验条件,有效实现SnO₂一维纳米结构的控制生长.采用扫描电子显微镜、能谱仪和X射线衍射仪表征产物形貌、成分和物相结构,并探讨了SnO₂微纳米材料的生长机理. 关键词： 2')" href="#">SnO₂ 纳米结构 亚微米环 生长机理     

氮对类金刚石薄膜的微观结构内应力与附着力的影响

采用原子力显微镜(AFM)、俄歇电子能谱(AES)和显微压痕分析等手段对射频等离子体增强化学气相沉积法制备的掺氮类金刚石(DLC：N)薄膜的微观结构和力学性能进行了研究.结果表明,随着含氮量的增加,DLC薄膜的AFM表面形貌中出现了几十纳米的颗粒,原子侧向力显微镜和AES分析表明这种纳米颗粒是x大于0.126的非晶氮化碳CN_x结构.这种非晶DLC/CN_x的纳米复合结构,减小了薄膜的内应力,从而提高了薄膜与衬底的附着力. 关键词： 类金刚石碳膜 微观结构 附着特性     

硅纳米线的PEOVD生长研究

本文以硅烷（SiH4）为反应气体,利用等离子体化学气相沉积（PECVD）方法在硅（100）衬底上生长硅纳米晶体、纳米线。应用扫描电镜观察不同条件下生长的样品表面,发现衬底条件对硅纳米结构的影响十分显著。在温度、压强等其它条件相同的情况下,对硅衬底应用Fe^3＋催化剂处理后,呈纳米线状结构生长,而无Fe催化剂涂覆情况下,基本呈纳米晶体状生长,说明催化剂对si纳米线的生成起了重要的促进生长作用。通过进一步研究硅纳米晶体、纳米线的等离子增强化学气相生长机理,发现它们以气-液-固（VLS）机制生长。     

硅衬底上纳米晶金刚石生长

研究了蚀刻气体对生长在硅衬底上纳米晶金刚石合成的影响.合成方法为热丝化学气相沉积法,衬底温度为550 oC,反应压力为4 kPa. 其中甲烷和氢气分别作为源气体和稀释气体. 氮气、氢气和氨气用作蚀刻气体. 结果表明,仅氢气作为蚀刻气体可获得最佳工艺条件.     

在双热舟化学气相沉积系统中通过掺In技术生长GaN纳米线和纳米锥

在现有的一台蒸发镀膜机基础上，设计加工了一个双热舟化学气相沉积系统.该系统具有真空度高、升温速度快、源和衬底温度可分别控制等优点，有利于化合物半导体纳米材料的生长.利用该生长系统，通过在生长过程中掺入等电子杂质In作为表面活性剂，分别在Si衬底和3C-SiC/Si衬底上生长出高质量的具有纤锌矿结构的单晶GaN纳米线和纳米尖三棱锥.所得产物通过场发射扫描电子显微镜、高分辨透射电子显微镜、能量色散x射线谱仪、x射线衍射仪，和荧光谱仪进行表征.这里所用的生长方法新颖，生长出的GaN纳米尖三棱锥在场发射和激光方面有潜在的应用价值. 关键词： GaN 纳米结构 透射电子显微镜 光致荧光谱     

PED沉积La-Sr-Cu-O薄膜表面的有序纳米结构

采用脉冲电子束沉积(PED)技术在Si(100)衬底上生长La_Sr_Cu_O薄膜，在750℃生长温度下获得具有有序纳米结构的表面形貌.采用聚集离子束(FIB)技术对获得的纳米结构进行表征，结果表明，这种有序的纳米结构是由于Si衬底和La_Sr_Cu_O薄膜之间的热膨胀系数和晶格的 失配引起的纳米裂纹.在这些纳米裂纹处，La_Sr_Cu_O成核生长获得独立的纳米线.通过控制 这种有序的纳米结构的生长，这种有序的纳米结构可以用来构造弱连接形成的器件. 关键词： 脉冲电子束沉积 La_Sr_Cu_O薄膜 纳米结构     

Photoluminescence and Raman analysis of novel ZnO tetrapod and multipod nanostructures

Novel ZnO tetrapod and multipod nanostructures were successfully synthesized in bulk quantity through thermal evaporation method. The morphologies and structures of the ZnO nanostructures were characterized by scanning electron microscopy, X-ray diffraction and transmission electron microscopy. The results revealed that the ZnO nanostructures consisted of tetrapods and multipods with tower-like legs. The ZnO nanostructures were of high purity and were well crystallized with wurtzite structure. The preferred growth direction of legs was found to be the [0 0 0 1] direction. Possible growth mechanisms were proposed for the formation of the ZnO nanostructures. Room temperature photoluminescence (PL) spectra showed that the as-synthesized ZnO nanostructures had a strong green emission centered at 495 nm and a weak ultraviolet emission at 383 nm. Raman spectroscopy was also adopted to explore the structural quality of the ZnO nanostructures.     

Patterned growth of ZnO nanorods and their field emission properties

Patterned zinc oxide (ZnO) nanorods were fabricated on the different patterned silicon nanocrystallite (SiNC) substrates via a simple thermal evaporation method without any catalyst. The as-synthesized products were examined by X-ray diffraction (XRD), scanning electron microscopy (SEM), respectively. The efficient field emission with low turn-on and threshold field, 3.5 V/μm and 8.1 V/μm, was obtained. The experimental results demonstrate that these products could be one of the promising candidates for field emission displays.     

Effects of the microstructure slab with pillars on light extraction of GaN light-emitting diode

The positive z direction relative light extraction efficiency of GaN light-emitting diodes with microstructure slab is calculated by three-dimensional finite-difference time-domain method, where the microstructure slab consists of a graphite lattice of pillars. The results show that the two-dimensional graphite-arranged pillars suppress light extraction. When there is a thick pillar in the middle of the pillars, the structure can enhance light extraction of the light-emitting diodes. The tower-like pillars, which are thin on the top of the pillars and thick on the bottom of the pillars, benefit the light extraction when the angle of the tower-like pillars is proper.     

Synthesis and optical properties of flower-like ZnO nanorods by thermal evaporation method

Flower-like ZnO nanorods have been synthesized by heating a mixture of ZnO/graphite powders using the thermal evaporation and vapor transport on Si (1 0 0) substrates without any catalyst. The structures, morphologies and optical properties of the products were characterized in detail by using X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), photoluminescence (PL) and Raman spectroscopy. The synthesized products consisted of large quantities of flower-like ZnO nanostructures in the form of uniform nanorods. The flower-like ZnO nanorods had high purity and well crystallized wurtzite structure, whose high crystalline quality was proved by Raman spectroscopy. The as-synthesized flower-like ZnO nanorods showed a strong ultraviolet emission at 386 nm and a weak and broad yellow-green emission in visible spectrum in its room temperature photoluminescence (PL) spectrum. In addition, the growth mechanism of the flower-like ZnO nanorods was discussed based on the reaction conditions.     

Rapid synthesis of novel flowerlike ZnO structures by thermolysis of zinc acetate

Novel flowerlike ZnO structures have been rapidly synthesized on (1 0 0)-Si substrates via thermolysis of zinc acetate in air ambient without any catalyst. The obtained ZnO products exhibit well-defined flowerlike morphologies consisting of multilayer petal crystals with tapering feature. High-resolution transmission electron microscope (HRTEM) and corresponding selected area electron diffraction pattern (SAED) reveal that these petal crystals are single crystal in nature and preferentially oriented in the c-axis direction. Room-temperature photoluminescence (PL) spectra show that all the samples exhibit prominent UV emissions around 376.8 nm and very weak visible emission peaks, which demonstrates that there are few deep-level defects in the single crystal petals of the flowerlike ZnO structures. The growth mechanism of the as-synthesized flowerlike ZnO structures was also discussed.     

CuO Nanosheets Synthesized by Hydrothermal Process

CuO nanosheets are synthesized by oxidation of commercial Cu substrates through the hydrothermal process at 150℃. The as-synthesized nanosheets are characterized by powder x-ray diffraction, transmission electron microscopy, selected area electron diffraction and x-ray photoelectron spectroscopy. For comparison, Cu substrates are also oxidized without NaOH added in precursor solution. The results show that the morphology of CuO could be controlled by NaOH, which demonstrates that NaOH can serve as a cosolvent and modifier in the reaction system. The possible mechanism of the growth of CuO nanosheets is also discussed.     

ZnO microbowls grown on ITO glass substrate through thermal evaporation

Novel ZnO microbowls are successfully synthesized by thermal evaporating of a mixture of ZnS powder and Zn powder. The morphologies of the as-synthesized products can be adjusted by changing the temperature and the type of substrate. The morphologies, microstructures, and photoluminescence properties are investigated by X-ray diffraction, Raman spectroscopy, scanning electron microscope, and photoluminescence spectroscopy respectively. The growth mechanism of the as-synthesized ZnO microbowls is proposed based on the experimental results. ZnO microbowls presented here can be used as building blocks to fabricate optical and optoelectronic micro/nano devices.     

ZnO microbowls grown on an ITO glass substrate through thermal evaporation

Novel ZnO microbowls are successfully synthesized by the thermal evaporating of a mixture of ZnS powder and Zn powder. The morphologies of the as-synthesized products can be adjusted by changing the temperature and the type of substrate. The morphologies, microstructures, and photoluminescence properties are investigated by X-ray diffraction, Raman spectroscopy, scanning electron microscope, and photoluminescence spectroscopy respectively. The growth mechanism of the as-synthesized ZnO microbowls is proposed based on the experimental results. ZnO microbowls presented here can be used as building blocks to fabricate optical and optoelectronic micro/nano devices.     

Formation of silicon oxide nanowires directly from Au/Si and Pd–Au/Si substrates

Amorphous silicon oxide (SiO_x) nanowires were directly grown by thermal processing of Si substrates. Au and Pd–Au thin films with thicknesses of 3 nm deposited on Si (0 0 1) substrates were used as catalysts for the growth of nanowires. High-yield synthesis of SiO_x nanowires was achieved by a simple heating process (1000–1150 °C) in an Ar ambient atmosphere without introducing any additional Si source materials. The as-synthesized products were characterized by field-emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, and transmission electron microscopy measurements. The SiO_x nanowires with lengths of a few and tens of micrometers had an amorphous crystal structure. The solid–liquid–solid model of nanowire formation was shown to be valid.     

ZnO nanorod arrays with tunable size and field emission properties on an ITO substrate achieved by an electrodeposition method

In the present work,vertically aligned ZnO nanorod arrays with tunable size are successfully synthesized on nonseeded ITO glass substrates by a simple electrodeposition method.The effect of growth conditions on the phase,morphology,and orientation of the products are studied in detail by X-ray diffraction(XRD),scanning electron microscopy(SEM),and transmission electron microscopy(TEM).It is observed that the as-prepared nanostructures exhibit a preferred orientation along c axis,and the size and density of the ZnO nanorod can be controlled by changing the concentration of ZnCl2.Field emission properties of the as-synthesized samples with different diameters are also studied,and the results show that the nanorod arrays with a smaller diameter and appropriate rod density exhibit better emission properties.The ZnO nanorod arrays show a potential application in field emitters.