沉积速率对甚高频等离子体增强化学气相沉积制备微晶硅薄膜生长标度行为的影响

本文采用甚高频等离子体增强化学气相沉积技术制备了沉积速率系列不同生长阶段的微晶硅薄膜,通过椭圆偏振技术研究了生长过程中微晶硅薄膜表面粗糙度的演化.实验结果表明:沉积速率为0.08和0.24nm/s的低速沉积时,硅薄膜表面粗糙度接近,生长指数分别为β=0.21和β=0.20,对应有限扩散生长模式,此时沉积速率对硅薄膜生长影响不大,原因是低速沉积时成膜先驱物有足够时间迁移到能量低的位置;当沉积速率增加到0.66nm/s时,硅薄膜表面粗糙度明显增加,生长指数β=0.81,大于0.5,出现了异常标度行为,与低速沉积的生长模式明显不同,原因是高速沉积时成膜前驱物来不及扩散就被下一层前驱物覆盖,降低了成膜前驱物在薄膜表面的扩散,使表面粗糙度增加和生长指数β增大.β大于0.5的异常标度行为与阴影效应有关.     

微晶硅薄膜的表面粗糙度及其生长机制的X射线掠角反射研究

采用等离子体增强化学气相沉积技术沉积一系列处于不同生长阶段的微晶硅薄膜.通过同步辐射X射线掠角反射技术研究微晶硅薄膜的表面粗糙度随时间等的演化，探讨微晶硅薄膜的生长动力学过程及其生长机制.研究结果表明，在衬底温度为200 ℃，电极间距为2 cm，沉积气压为6.66×1０² Pa，射频功率密度为0.22 W/cm²，氢稀释度分别为99%和98%的沉积条件下，在玻璃衬底上生长的微晶硅薄膜生长指数β分别为0.21±0.01和0.24±0.01.根据KPZ模型，微晶硅薄膜的生长机制为有限扩散生长. 关键词： X射线掠角反射 微晶硅薄膜 表面粗糙度 生长机制     

多晶薄膜表面粗化与生长方式转变

采用原子力显微镜研究了磁控溅射多晶薄膜表面粗化行为对归一化沉积温度T_s/T_m(T_s是沉积温度，T_m是材料熔点)的依赖性与薄膜生长方式转变行为.随着T_s/T_m增加，薄膜表面粗糙度增加，而表征粗糙度随时间演化特征的生长指数β历经了先减小再增加的过程.β对T_s/T_m的依赖关系反映了薄膜生长方式的转变行为，即薄膜生长依次由随机生长方式向表面扩散驱动生长方式与异常标度行为生长方式转变.在低于体扩散控制薄膜生长的温度时，晶界扩散机理导致多晶薄膜的表面粗化的异常标度行为. 关键词： 多晶薄膜 表面粗化 温度 生长     

高速沉积微晶硅薄膜光发射谱的研究

采用PR650光谱光度计对高速沉积微晶硅薄膜的生长过程进行了在线监测研究,并对所对应的材料进行了Raman谱和红外吸收谱(FTIR)的测试.结果表明：能反映材料晶化程度的I_［SiH^*］/I_［Hβ^*］比值在沉积时间为100 s之内有下降的趋势,且反应气体总流量T_fl越小下降趋势越明显,这与拉曼散射光谱对材料的结构测试结果一致;沉积5 min时I 关键词： 高速沉积 微晶硅薄膜 电子温度     

HW-MWECR-CVD法制备氢化微晶硅薄膜及其微结构研究

用热丝辅助微波电子回旋共振化学气相沉积方法制备出高晶化体积分数的氢化微晶硅(μc-Si:H)薄膜.拉曼散射和X射线衍射技术对样品的微观结构测量分析表明，当反应气体中SiH₄浓度在3.6%—50%之间大范围变化时，μc-Si:H薄膜均具有高的晶化体积分数.进一步的分析表明，在SiH₄浓度较大时制备的薄膜，其结构以非晶-微晶的过渡相为主.薄膜易于晶化或生长为过渡相的主要原因是微波电子回旋共振使SiH₄气体高度分解，等离子体高度电离. 关键词： 微波电子回旋共振化学气相沉积 氢化微晶硅薄膜 拉曼散射 X射线衍射     

气体滞留时间对高速沉积的微晶硅薄膜性能的影响分析

实现高速沉积对于薄膜微晶硅太阳电池产业化降低成本是一个重要手段.采用超高频等离子体增强化学气相沉积(VHF-PECVD)技术，实现了微晶硅硅薄膜的高速沉积，并通过改变气体总流量改变气体滞留时间，考察了气体滞留时间在化学气相沉积(CVD)过程中对薄膜的生长速率以及光电特性和结构特性的影响.采用沉积速率达到12?/s的高速微晶硅工艺制备微晶硅电池，电池效率达到了5.3％. 关键词： 气体滞留时间 高速沉积 微晶硅 超高频等离子体增强化学气相沉积     

斜角入射沉积法制备渐变折射率薄膜的折射率分析

斜角入射沉积法是一种制备薄膜的新颖方法,它可以用来制备渐变折射率薄膜.本文首先探讨了膜料的沉积入射角为α,薄膜柱状生长倾斜角为β时的薄膜的填充系数;之后利用drude理论,分析研究了斜角入射沉积法制备渐变折射率薄膜的折射率与薄膜的入射角和生长方向的关系. 关键词： 斜角入射沉积 渐变折射率 填充系数     

甚高频高速沉积微晶硅薄膜的研究

采用甚高频化学气相沉积(VHF-PECVD)技术制备了系列微晶硅(μc-Si:H)薄膜样品,重点研究了硅烷浓度、功率密度、沉积气压和气体总流量对薄膜沉积速率和结晶状态的影响,绘制了沉积气压和功率密度双因素相图. 以0.75nm/s的高速沉积了器件质量级的微晶硅薄膜,并以该沉积速率制备出了效率为5.5%的单结微晶硅薄膜电池. 关键词： 微晶硅薄膜 高速沉积 甚高频化学气相沉积     

高速沉积本征微晶硅的优化及其在太阳电池中的应用

采用高压高功率的甚高频等离子体增强化学气相沉积（VHF-PECVD）技术高速（沉积速率约为1.2 nm/s）沉积了一系列不同厚度的本征微晶硅薄膜,并通过Raman谱和XRD谱的测试,研究了高速沉积时本征微晶硅薄膜的微结构演变特性及其对电池性能的影响.针对其微结构特性及高速沉积本身存在的离子轰击作用强的特点,提出了在沉积微晶硅薄膜过程中采用功率梯度的方法,达到有效地控制薄膜微结构变化的目的,并在一定功率梯度范围内降低了电子温度,提高了薄膜质量,从而使电池效率明显提高.最后在沉积速率为1.2 nm/s时,制备 关键词： 高速沉积 微晶硅薄膜 微结构演变 功率梯度     

衬底温度和硼掺杂对p型氢化微晶硅薄膜结构和电学特性的影响

以B₂H₆为掺杂剂,采用射频等离子体增强化学气相沉积技术在玻璃衬底上制备p型氢化微晶硅薄膜.研究了衬底温度和硼烷掺杂比对薄膜的微结构和暗电导率的影响.结果表明：在较高的衬底温度下很低的硼烷掺杂比即可导致薄膜非晶化;在实验范围内,随着衬底温度升高薄膜的晶化率单调下降,暗电导率先缓慢增加然后迅速下降,变化趋势与硼烷掺杂比的影响极为相似.最后着重讨论了p型氢化微晶硅薄膜的生长机理. 关键词： p型氢化微晶硅薄膜 衬底温度 晶化率 电导率     

椭圆偏振光谱实时在线监测与离线分析微晶硅薄膜的生长

采用甚高频等离子体增强化学气相沉积技术高速沉积了有无籽晶层两个系列微晶硅薄膜,通过椭圆偏振光谱、拉曼光谱和XRD对薄膜进行了分析,发现采用籽晶层后,在薄膜沉积初期有促进晶化的作用;由于籽晶层减少了薄膜的诱导成核时间,提高了薄膜的沉积速率,对比了实时在线和离线椭圆偏振光谱两种测量状态对分析微晶硅薄膜的影响,研究发现,当薄膜较薄时,实时在线测量得到的薄膜厚度小于离线下的数值;当薄膜较厚时,两种测量条件下得到的薄膜厚度差异较小;实时在线条件下得到的表面粗糙度要大于离线条件下得到的数值,这是由于薄膜暴露在大气中后表面有硅氧化物生成,对表面有平滑作用.     

Deposition of MgO films by pulsed mid-frequency magnetron sputtering

MgO films were deposited by pulsed mid-frequency magnetron sputtering from metallic targets in the mixture of Ar and O₂ gas. The surface morphology, crystalline structure, and optical properties were characterized by using atomic force microscopy (AFM), X-ray diffraction (XRD), and spectroscopic ellipsometry, respectively. The secondary electron emission coefficients of MgO films were measured by using a self-made apparatus in He gas. A pronounced hysteresis phenomenon of target voltage, current, and deposition rate with increasing and decreasing O₂ flow rate was observed. The structure of films deposited at a metallic mode changes from Mg phase to the mixed Mg and MgO phase, and the films have a very rough surface. All the films deposited at oxide mode have high transparency and smooth surface, and show (2 2 0) preferred orientation growth. The refractive index and extinction coefficient at a wavelength of 670 nm for MgO films deposited at oxide mode with a O₂ flow rate of 3 sccm are 1.698 and 1.16×10⁻⁴, respectively. The secondary emission coefficient at a E/p of 57.8 V/(cm Torr) for MgO films deposited at a O₂ flow rate of 3 sccm is 0.16, which is higher than that of MgO films deposited by e-beam evaporation.     

Influence of Boron doping on microcrystalline silicon growth

Microcrystalline silicon (μc-Si:H) thin films with and without boron doping are deposited using the radio-frequency plasma-enhanced chemical vapour deposition method. The surface roughness evolutions of the silicon thin films are investigated using ex situ spectroscopic ellipsometry and an atomic force microscope. It is shown that the growth exponent β and the roughness exponent α are about 0.369 and 0.95 for the undoped thin film, respectively. Whereas, for the boron-doped μc-Si:H thin film, β increases to 0.534 and α decreases to 0.46 due to the shadowing effect.     

Morphological and optical properties of silicon thin films by PLD

Silicon thin films have been prepared on sapphire substrates by pulsed laser deposition (PLD) technique. The films were deposited in vacuum from a silicon target at a base pressure of 10⁻⁶ mbar in the temperature range from 400 to 800 °C. A Q-switched Nd:YAG laser (1064 nm, 5 ns duration, 10 Hz) at a constant energy density of 2 J × cm⁻² has been used. The influence of the substrate temperature on the structural, morphological and optical properties of the Si thin films was investigated.Spectral ellipsometry and atomic force microscopy (AFM) were used to study the thickness and the surface roughness of the deposited films. Surface roughness values measured by AFM and ellipsometry show the same tendency of increasing roughness with increased deposition temperature.     

Deposition pressure effect on the surface roughness scaling of microcrystalline silicon films

The scaling behaviour of surface roughness evolution of microcrystalline silicon (μc-Si:H) films prepared by very-high frequency plasma-enhanced chemical vapour deposition (VHF-PECVD) has been investigated by using a spectroscopic ellipsometry (SE) technique. The growth exponent β was analysed for the films deposited under different pressures P_g. The results suggest that films deposited at P_g = 70 Pa have a growth exponent β about 0.22, which corresponds to the definite diffusion growth. However, abnormal scaling behaviour occurs in the films deposited at P_g = 300 Pa. The exponent β is about 0.81 that is much larger than 0.5 of zero diffusion limit in the scaling theory. The growth mode of μ c-Si:H deposited at P_g= 300 Pa is clearly different from that of μc-Si:H at P_g = 70 Pa. Monte Carlo simulations indicate that the sticking process and the surface diffusion of the radicals are two key factors to affect the growth mode under different pressures. Under P_g= 300 Pa, β>0.5 is correlated with the strong shadowing effect resulting from the larger sticking coefficient.     

Optical characterization and microstructure of BaTiO3 thin films obtained by RF-magnetron sputtering

BaTiO₃ thin films were deposited on Pt/Ti/SiO₂/Si by rf planar-magnetron sputtering. The films thickness increases with the decrease of both deposition pressure and sample-discharge centre distance. The films annealed at 900 °C, for 8 h, present direct band gap energy ranged between 3.57 and 3.59 eV. The dependence of the structure and microstructure (texture, degree of crystallinity), as well as of the optical characteristics on the deposition parameters, was analysed. Using spectroscopic ellipsometry (SE) measurements coupled with the Bruggeman Effective Medium Approximation (B-EMA), the layer structure and the surface roughness, were determined. The root mean square roughness values of the surface layer, estimated by atomic force microscopy (AFM) analyses, are ranged between 10 and 20 nm and were in good agreement with SE data.The obtained films have tetragonal unit cell and show densely packed, non-columnar morphology and hexagon-like crystallite shape.     

Scaling of the interface roughness in Fe-Cr superlattices: self-affine versus non-self-affine

We have analyzed kinetic roughening in Fe-Cr superlattices by energy-filtered transmission electron microscopy. The direct access to individual interfaces provides both static and dynamic roughness exponents. We find an anomalous non-self-affine scaling of the interface roughness with a time dependent local roughness at short length scales. While the deposition conditions affect strongly the long-range dynamics, the anomalous short-range exponent remains unchanged. The different short- and long-range dynamics outline the importance of long-range interactions in kinetic roughening.     

Mo2C膜表面粗糙化规律的计算机模拟

引入晶粒边界修正,改进了Ｍｏ２Ｃ膜表面粗糙化物理模型,将ＤＴ２模型推广到包括有温度的情况对Ｍｏ２Ｃ膜表面形态进行计算机模拟并统计模拟图的高度分布,确定表面粗糙度随沉积时间和基底温度的变化规律,结果表明：引入晶粒边界修正大大促进了理论与实验结果的一致,Ｍｏ２Ｃ膜表面粗糙化属快速粗造化,粗造度随基底温度升高在而非线性地增大。     

沉积工艺条件对金刚石薄膜红外椭偏光学性质的影响

采用红外椭圆偏振光谱仪对不同工艺条件下制备的CVD金刚石薄膜在红外波长范围内的光学参量进行了测量，分析了工艺条件对金刚石薄膜红外光学性质的影响.获得了最佳的沉积工艺参数，优化了薄膜的制备工艺.结果表明薄膜的折射率和消光系数与薄膜质量密切相关，当温度为750℃，碳源浓度为0.9%和压强为4.0 kPa时，金刚石薄膜的红外椭偏光学性质最佳，折射率平均值为2.385，消光系数在10^-4范围内，在红外波段具有良好的透过性. 关键词： 薄膜光学 红外光学性质 工艺条件 金刚石薄膜