彩色透明微晶玻璃的吸收光谱

在Li2O-Al2O3-SiO2系统玻璃中掺入少量晶核剂TiO2,ZrO2,P2O5，再掺入稀土离子和过渡金属离子作为着色剂，在高温下溶制得到彩色透明玻璃，对上述玻璃进行微晶化处理，用差热分析（DTA）确定其晶化温度，测定与讨论了所获彩色透明微晶玻璃在紫外波段至近红外波段的吸收光谱特性，研究结果表明，玻璃微晶化后，由于基质玻璃对光的微弱散射，引起吸收的增强，但不改变稀土离子和过渡金属离子的本征吸收峰位。     

Er3+单掺和Er3+/Yb3+双掺铋硼酸盐玻璃的研究

用高温熔融法制备了Er^3 单掺和Er^3 /Yb^3 双掺铋硼酸盐玻璃样品，测量了上述玻璃样品的吸收光谱，荧光光谱，荧光寿命以及红外透过率。对高浓度掺杂Er^3 的铋硼酸盐玻璃中的浓度猝灭现象作出了解释。分析了Er^3 ／Yb^3 双掺铋硼酸盐玻璃样品中Yb^3 离子对Er^3 离子的敏化过程。研究发现Er^3 ／Yb^3 双掺铋硼酸盐玻璃在1．5～1．6μm波段有宽达81nm的荧光半峰全宽。实验还发现在熔制过程中通入氧气对其荧光寿命和红外透过率都有明显的提高。由于该玻璃材料表现出较好的物化性能。因此该材料可望成为宽带光纤放大器的适宜的基质材料。     

含Ho~(3+)的GeO_2-B_2O_3-BaO-Na_2O-Al_2O_3锗酸盐玻璃的光谱与增益特性

用高温熔融法制备了不同Ho3+离子掺杂浓度65GeO2-12B2O-10BaO-10Na2O-3Al2O3-χHo2O3(χ=0.25,0.75,1.25mol%)锗酸盐玻璃。从吸收特性出发,应用McCumber理论计算了Ho3+离子能级5I8→5I7(~2.0μm)跃迁的吸收截面和5I7→5I8的受激发射截面。根据掺杂离子的浓度以及获得的吸收截面和受激发射截面得到Ho3+离子在此玻璃中的增益截面函数,从该函数可反映出材料的粒子数反转特性。获得的基本光学参数与其它掺杂的玻璃进行了比较,其吸收截面、发射截面和增益截面的最大值具有一定的优势。认为该玻璃在~2.0μm波段的中红外激光器中将有潜在的较大应用前景。     

溶胶—凝胶法制备SiO2基片Er^3＋：Al2O3光学薄膜

用溶胶—凝胶法在SiO2基片上提拉制备了掺Er^3 ：Al2O3光学薄膜。采用扫描电子显微镜、原子力显微镜、差热—热重分析仪、X射线衍射仪研究了掺Er^3 ：Al2O3光学薄膜的肜貌和结构特性。在900℃烧结后，SiO2基片上提拉15次形成厚度8μm掺摩尔比0．01Er^3 的面心立方结构γ-Al2O3薄膜具有明显(110)择优取向，掺摩尔比0．01Er^3 对γ—Al2O3的品体结构和结晶生长过程木产生显著影响。薄膜具有均匀多孔结构，平均粒径为30～100nm，平均孔径为50～100nm，表面起伏度为10～20nm。掺摩尔比0．01Er^3 ：rAl2O3薄膜，获得了中心波长为1．534μm(半峰全宽为36nm)的光敛发光谱。     

掺铒碲-钨-钠玻璃基质的光谱性质研究

制备了用于离子交换法制备光波导器件的掺铒碲-钨-钠玻璃基质。应用扎得-奥菲而特(Judd—Ofelt)理论计算了玻璃样品的三个强度参量,由强度参量计算了Er^3 离子的自发跃迁几率、荧光分支比等光谱参量;应用麦克库玻(McCumber)理论,计算了Er^3 离子在1．5μm的受激发射截面,荧光测试发现Er^3 离子的荧光半峰全宽可达65nm。比较了Er^3 离子在不同玻璃基质中的光谱特性。结果表明,Er^3 离子在碲-钨-钠玻璃中具有较高的受激发射截面和较宽的荧光半峰全宽,可以用于宽带光波导器件的制备。     

Tm3+/Ho3+共掺镓铋酸盐玻璃1.47 μm发光特性和能量传递的研究

报道了Tm3+/Ho3+共掺的镓铋酸盐玻璃14Ga2O3-25Bi2O3-20GeO2-31PbO-10PbF2玻璃1.47μm(S波段)发光和能量传递特征,应用Judd-Ofelt理论计算了玻璃的强度参数Ω,(t=2,4,6),自发辐射概率 A、荧光分支比β,荧光辐射寿命τ等各项光谱参数以及有效荧光线宽△λeff和峰值发射截面σpeake.通过测量荧光光谱和荧光寿命研究了Ho3+离子掺杂浓度对Tm3+离子1.47μm波段发光性能的影响,分析了Tm3+和Ho3+之间的能量传递过程.结果表明一定浓度内Ho3+的共掺迅速降低了Tm3+:3 F4能级的粒子数,而对3H4能级粒子数影响不大,从而降低了3F4和3H4能级间布居数反转的难度,极大地提高了1.47 μm发光效率.研究表明镓铋酸盐玻璃是适用于S波段光纤放大器的一种潜在基质材料,而掺杂一定浓度的Ho3+离子有利于提高Tm3+离子在1.47μm波段的发光效率.     

Li2O-Al2O3-SiO2微晶玻璃加工脆延转变临界条件实验研究

 介绍了Li2O-Al2O3-SiO2微晶玻璃的加工特点。基于纳米划痕技术对Li2O-Al2O3-SiO2微晶玻璃进行了纳米划痕实验,测得微晶玻璃材料脆延转变临界切削深度和临界载荷的平均值分别为125.6 nm和29.78 mN。将实验所得临界切削深度值与基于压痕断裂力学模型建立的脆延转变临界切削深度计算值进行了对比,结果表明,T. G. Bifano基于显微压痕法给出的临界切削深度计算值与实验结果差别较大,结合实验结果对其公式进行了修正;基于压痕断裂力学模型建立的延性域磨削临界切削深度计算值与实验结果相差较小,并分析了产生差异的原因。     

宽带光放大器用掺Er3+碲钨酸盐玻璃

制备了掺Er^3 的TeO2-WO3-ZnO-ZnF2(TWZOF)玻璃,测量了Er^3 在玻璃中的吸收光谱和970nm激光二极管激发下的荧光光谱和荧光寿命,分别采用J-O理论和McCumber理论计算了Er^3 离子的J-O强度参量Ωt(t=2,4,6)和其1．5μm发射的吸收截面和发射截面,研究了其荧光强度、荧光寿命和发射带宽与ZnF2含量的关系。结果表明,Er^3 在TWZOF玻璃中具有较大的1．5μm发射截面,其峰值发射截面为0．86pm^2;同时,Er^3 在TWZOF玻璃中具有很大的1．5μm发射带宽,所得半峰全宽在68～83nm之间;Er^3 在TWZOF玻璃中还具有较小的Ω2值和较大的Ω6值,且随ZnF2含量的增加,Ω2和Ω4均增大;Er^3 离子1．5μm发射峰值荧光强度和荧光寿命总体也随ZnF2含量的增加而增加。     

激光高反射膜的研究

研究混合膜（TiO2 Ta2O3;Ta2O5 ZrO2)的色散规律，用Ta2O5 ZrO2和SiO2成功地镀制出两个波段（632．8nm,1.06μm)的激光反射膜，使激光破坏阈值提高5％－15％（1．06μm)，膜层吸收小，机械强度增加。     

在硅片上沉积厚二氧化硅的火焰水解法研究

用火焰水解和高温烧结的方法在单晶硅基片上制备了厚SiO2和B2O2-P2O2-SiO2光波导包层材料。并用扫描电镜(SEM)和X射线粉末衍射(XRD)方法对其微观形貌和物相结构进行了观察和检测。重点对硅基片上沉积厚SiO2时的龟裂和析晶问题进行了深入研究。从扫描电镜照片可以看出．火焰水解法形成的SiO2粉末呈多孔的蜂窝状结构。这种粉末具有很高的比表面积,因而很容易烧结成玻璃。X射线衍射图谱表明．这种粉末是完全非晶态的。经过烧结以后,从扫描电镜照片可以明显看出硅基片上的SiO2薄膜出现龟裂。同时,X射线衍射测试结果表明有少量SiO2析晶。而通过在SiO2中掺入B2O3、P2O5,上述龟裂和析晶完全消失。用这种工艺制备的SiO2波导包层材料厚度达到20μm以上,表面光滑、没有龟裂,而且是完全玻璃态的,可以用于制备性能优良的各种硅基二氧化硅波导器件。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.