GaN基激光器多量子阱垒材料的研究

在(0001)蓝宝石衬底上分别用金属有机化学气相沉积技术外延生长了InGaN/GaN, InGaN/InGaN, InGaN/AlInGaN多量子阱激光器结构, 并分别制作了脊形波导GaN基激光器。同步辐射X射线衍射,电注入受激发射光谱测试及光功率-电流(L-I)测试证明,相对于GaN垒材料,InGaN垒材料,AlInGaN四元合金垒材料更能改善多量子阱的晶体质量,提高量子阱的量子效率及降低激光器阈值电流。相关的机制为：组分调节合适的四元合金垒层中Al的掺入使得量子阱势垒高度增加,阱区收集载流子的能力增强;In的掺入能更多地补偿应力,减少了由于缺陷和位错所产生的非辐射复合中心密度;In的掺入还减小了量子阱中应力引致的压电场,电子空穴波函数空间交叠得以加强,使得辐射复合增加。     

初始化生长条件对a-GaN中应变的影响

利用高分辨X射线衍射(HRXRD)与拉曼散射光谱(Raman scattering spectra)研究了氮化处理与低温AlN缓冲层对低压金属有机化学气相沉积(LP-MOCVD)在r面蓝宝石衬底上外延的a面GaN薄膜中的残余应变的影响。实验结果表明:与氮化处理后生长的a-GaN相比,使用低温AlN缓冲层后生长的a-GaN具有较小的摇摆曲线的半高宽和较低的残余应变,而且其结构各向异性和残余应变各向异性也均有一定程度的降低。因此,与氮化处理相比,低温AlN缓冲层更有利于a-GaN的生长。     

Stranski–Krastanov growth of InGaN quantum dots emitting in green spectra

Self-assembled InGaN quantum dots (QDs) were grown on GaN templates by metalorganic chemical vapor deposition. 2D–3D growth mode transition through Stranski–Krastanov mode was observed via atomic force microscopy. The critical thickness for In_0.67Ga_0.33N QDs was determined to be four monolayers. The effects of growth temperature, deposition thickness, and V/III ratio on QD formation were examined. The capping of InGaN QDs with GaN was analyzed. Optimized InGaN quantum dots emitted in green spectra at room temperature.     

Nonpolar a-plane GaN grown on r-plane sapphire using multilayer AlN buffer by metalorganic chemical vapor deposition

Mirror-like and pit-free non-polar a-plane (1 1 −2 0) GaN films are grown on r-plane (1 −1 0 2) sapphire substrates using metalorganic chemical vapor deposition (MOCVD) with multilayer high-low-high temperature AlN buffer layers. The buffer layer structure and film quality are essential to the growth of a flat, crack-free and pit-free a-plane GaN film. The multilayer AlN buffer structure includes a thin low-temperature-deposited AlN (LT-AlN) layer inserted into the high-temperature-deposited AlN (HT-AlN) layer. The results demonstrate that the multilayer AlN buffer structure can improve the surface morphology of the upper a-plane GaN film. The grown multilayer AlN buffer structure reduced the tensile stress on the AlN buffer layers and increased the compressive stress on the a-plane GaN film. The multilayer AlN buffer structure markedly improves the surface morphology of the a-plane GaN film, as revealed by scanning electron microscopy. The effects of various growth V/III ratios was investigated to obtain a-plane GaN films with better surface morphology. The mean roughness of the surface was 1.02 nm, as revealed by atomic force microscopy. Accordingly, the multilayer AlN buffer structure improves the surface morphology and facilitates the complete coalescence of the a-plane GaN layer.     

利用MOCVD在r面蓝宝石上生长的α面GaN中两步AlN缓冲层的优化

采用两步AlN缓冲层(一层低温AlN和一层高温AlN)在r面蓝宝石衬底上生长了非极性的α面GaN,并利用高分辨X射线衍射和光致荧光谱对所生长的材料进行了研究.两步AIN缓冲层在我们之前的工作中已被证明比单步高温AlN或低温GaN缓冲层更有利于减小材料各向异性和提高晶体质量,本文进一步优化了两步AlN缓冲层的结构,并得到了各向异性更小,晶体质量更好的α面GaN薄膜.分析表明,两步AlN缓冲层中的低温AlN层在减小各向异性中起着关键作用.低温AlN层能抑制了优势方向(c轴)的原子迁移,有利于劣势方向(m轴)的原子迁移,从而减小了Al原子在不同方向迁移能力的差异,并为其后的高温AlN缓冲层和GaN层提供"生长模板",以得到各向异性更小、晶体质量更好的α面GaN材料.     

High-efficiency InGaN/AlInGaN multiple quantum wells with lattice-matched AlInGaN superlattices barrier

A new approach to fabricating high-quality AlInGaN film as a lattice-matched barrier layer in multiple quantum wells(MQWs) is presented. The high-quality AlInGaN film is realized by growing the AlGaN/InGaN short period superlattices through metalorganic chemical vapor deposition, and then being used as a barrier in the MQWs. The crystalline quality of the MQWs with the lattice-matched AlInGaN barrier and that of the conventional InGaN/GaN MQWs are characterized by x-ray diffraction and scanning electron microscopy. The photoluminescence(PL) properties of the InGaN/AlInGa N MQWs are investigated by varying the excitation power density and temperature through comparing with those of the InGaN/GaN MQWs. The integral PL intensity of InGaN/AlInGaN MQWs is over 3 times higher than that of InGaN/GaN MQWs at room temperature under the highest excitation power. Temperature-dependent PL further demonstrates that the internal quantum efficiency of InGaN/AlInGaN MQWs(76.1%) is much higher than that of InGaN/GaN MQWs(21%).The improved luminescence performance of InGaN/AlInGaN MQWs can be attributed to the distinct reduction of the barrier-well lattice mismatch and the strain-induced non-radiative recombination centers.     

利用MOCVD在r面蓝宝石上生长的α面GaN中两步AlN缓冲层的优化

采用两步AlN缓冲层(一层低温AlN和一层高温AlN)在r面蓝宝石衬底上生长了非极性的α面GaN,并利用高分辨X射线衍射和光致荧光谱对所生长的材料进行了研究.两步AIN缓冲层在我们之前的工作中已被证明比单步高温AlN或低温GaN缓冲层更有利于减小材料各向异性和提高晶体质量,本文进一步优化了两步AlN缓冲层的结构,并得到...     

Estimation of InN phase inclusion in InGaN films grown by MOVPE

The amount of InN included in InGaN films grown by MOCVD (metalorganic chemical vapor deposition) was estimated by X-ray diffraction measurement technology. The In compositions in our InGaN films are measured as 0.1–0.34 by X-ray 2θ scan using Vegard’s law. The inclusion of InN in InGaN layers was obtained as 0.0684–2.6396% by measuring the ratio of the integrated intensity of the InN (0002) peak to that of the InGaN (0002) peak in X-ray rocking curves. The theoretical diffraction intensities from InN and InGaN have been calculated according to the X-ray-diffraction theory. The values of the InN inclusion for all our samples were less than 3%, which indicated that the degree of phase separation of the samples was low. It was also found that the flow rate of N₂ carrier gas and the operation pressure strongly affected the InN inclusion in InGaN. Received: 20 November 2000 / Accepted: 16 May 2001 / Published online: 27 June 2001     

InGaN合金中LO声子-等离子激元耦合模的研究

分别采用532,488 nm可见光和325 nm紫外光激发,对金属有机化学气相沉积法在蓝宝石衬底上生长的六方相InGaN/GaN薄膜样品在室温和78 K低温下的拉曼散射谱进行了研究。在可见光激发时,E₂模和A₁(LO)模的散射信号主要来自GaN层;采用紫外光激发时,A₁(LO)模向低频方向移动且共振增强,此散射信号来自InGaN层。在可见光激发的情况下,在A₁(LO)模的高频方向观察到一个宽峰,此宽峰为InGaN的LO声子-等离子激元耦合模,根据耦合模频率得到InGaN层中的电子浓度为n_ｅ＝1.61×1018 cm-3。紫外光激发时,没有观察到耦合模,A₁(LO)模散射信号主要来自样品表面耗尽层,由此估算样品中的耗尽层宽度大约在40 nm。此外,还对比分析了在室温和78 K低温下LO声子-等离子激元耦合模的散射强度的变化规律,计算了不同温度下等离子激元的屏蔽波矢。这些结论对于了解InGaN材料的基本性质以及氮化物光电器件的开发利用都有重要参考价值。     

Influence of growth parameters on the properties of InGaN/GaN multiple quantum well grown by metalorganic chemical vapor deposition

The effects of growth parameters such as barrier growth time, growth pressure and indium flow rate on the properties of InGaN/GaN multiple quantum wells (MQWs) were investigated by using photoluminescence (PL), high resolution X-ray diffraction (HRXRD), and atomic force microscope (AFM). The InGaN/GaN MQW structures were grown on c-plane sapphire substrate by using metalorganic chemical vapor deposition. With increasing barrier growth time, the PL peak energy is blue-shifted by 18 nm. For InGaN/GaN MQW structures grown at different growth pressures, the PL intensity is maximized in the 300 Torr – grown structure, which could be attributed to the improved structural quality confirmed by HRXRD and AFM results. Also, the optical properties of InGaN/GaN MQW are strongly affected by the indium flow rate.     

Superior material qualities and transport properties of InGaN channel heterostructure grown by pulsed metal organic chemical vapor deposition

Pulsed metal organic chemical vapor deposition is introduced into the growth of In Ga N channel heterostructure for improving material qualities and transport properties. High-resolution transmission electron microscopy imaging shows the phase separation free In Ga N channel with smooth and abrupt interface. A very high two-dimensional electron gas density of approximately 1.85 × 1013cm-2is obtained due to the superior carrier confinement. In addition, the Hall mobility reaches 967 cm2/V·s, owing to the suppression of interface roughness scattering. Furthermore, temperature-dependent Hall measurement results show that In Ga N channel heterostructure possesses a steady two-dimensional electron gas density over the tested temperature range, and has superior transport properties at elevated temperatures compared with the traditional Ga N channel heterostructure. The gratifying results imply that In Ga N channel heterostructure grown by pulsed metal organic chemical vapor deposition is a promising candidate for microwave power devices.     

Mid-gap photoluminescence and magnetic properties of GaMnN films grown by metal–organic chemical vapor deposition

Metal-organic chemical vapor deposition （MOCVD） grown ferromagnetic GaMnN films are investigated by photo- luminescence （PL） measurement with a mid-gap excitation wavelength of 405 nm. A sharp PL peak at 1.8 eV is found and the PL intensity successively decreases with the addition of Mn, in which the Mn concentration of sample A is below 1% （[Mn]A =0.75%） but its PL intensity is stronger than other samples＇. The 1.8-eV PL peak is attributed to the recombination of electrons in the t2 state of the neutral Mn3＋ acceptor with holes in the valence band. With Mn concentration increasing, the intensity of the PL peak decreases and the magnetic increment reduces in our samples. The correlation between the PL peak intensity and ferromagnetism of the samples is discussed in combination with the experimental results.     

Direct growth of graphene on gallium nitride by using chemical vapor deposition without extra catalyst

Graphene on gallium nitride(GaN) will be quite useful when the graphene is used as transparent electrodes to improve the performance of gallium nitride devices. In this work, we report the direct synthesis of graphene on GaN without an extra catalyst by chemical vapor deposition. Raman spectra indicate that the graphene films are uniform and about 5–6 layers in thickness. Meanwhile, the effects of growth temperatures on the growth of graphene films are systematically studied, of which 950℃ is found to be the optimum growth temperature. The sheet resistance of the grown graphene is 41.1Ω/square,which is close to the lowest sheet resistance of transferred graphene reported. The mechanism of graphene growth on GaN is proposed and discussed in detail. XRD spectra and photoluminescence spectra indicate that the quality of GaN epi-layers will not be affected after the growth of graphene.     

Interface characterization and indium content of indium-rich quantum dots in InGaN/GaN multiple quantum wells

We report on the interface characterization of InGaN/GaN multiple quantum wells with indium aggregation grown by metalorganic chemical vapor deposition. The interface related microstructure was analyzed by high-resolution transmission electron microscopy, high-resolution X-ray diffraction and high angle annular dark field. Luminescence measurements were carried out by micro-photoluminescence measurement. In addition, quantitative determination of the indium concentration inside the ultra-small dots was attempted. We demonstrate that the quantum dots are coherent and the interfaces remain sharp. The In content inside ∼2 nm InGaN dots is about 65% determined by spectrum imaging in energy-filtered transmission electron microscopy combined with multiple linear least squares fitting, which is slighter higher than the value obtained either from HRTEM or theoretical calculations. This discrepancy is briefly discussed but demands further studies for complete understanding.     

Influence of reaction parameters on synthesis of high-quality single-layer graphene on Cu using chemical vapor deposition

Large-area monolayer graphene samples grown on polycrystalline copper foil by thermal chemical vapor deposition with differing CH4 flux and growth time are investigated by Raman spectra, scanning electron microscopy, atomic force microscopy, and scanning tunneling microscopy. The defects, number of layers, and quality of graphene are shown to be controllable through tuning the reaction conditions: ideally to 2–3 sccm CH4 for 30 minutes.     

Improvement in a-plane GaN crystalline quality using wet etching method

Nonpolar （1120） GaN films are grown on the etched a-plane GaN substrates via metalorganic vapor phase epitaxy. High-resolution X-ray diffraction analysis shows great decreases in the full width at half maximum of the samples grown on etched substrates compared with those of the sample without etching, both on-axis and off-axis, indicating the reduced dislocation densities and improved crystalline quality of these samples. The spatial mapping of the E2 （high） phonon mode demonstrates the smaller line width with a black background in the wing region, which testifies the reduced dislocation densities and enhanced crystalline quality of the epitaxial lateral overgrowth areas. Raman scattering spectra of the E2 （high） peaks exhibit in-plane compressive stress for all the overgrowth samples, and the E2 （high） peaks of samples grown on etched substrates shift toward the lower frequency range, indicating the relaxations of in-plane stress in these GaN films. Furthermore, room temperature photoluminescence measurement demonstrates a significant decrease in the yellow-band emission intensity of a-plane GaN grown on etched templates, which also illustrates the better optical properties of these samples.     

Low-leakage-current AIGaN/GaN HEMTs on Si substrates with partially Mg-doped GaN buffer layer by metal organic chemical vapor deposition

High-performance low-leakage-current A1GaN/GaN high electron mobility transistors （HEMTs） on silicon （111） sub- strates grown by metal organic chemical vapor deposition （MOCVD） with a novel partially Magnesium （Mg）-doped GaN buffer scheme have been fabricated successfully. The growth and DC results were compared between Mg-doped GaN buffer layer and a unintentionally onμe. A 1μ m gate-length transistor with Mg-doped buffer layer exhibited an OFF-state drain leakage current of 8.3 × 10-8 A/mm, to our best knowledge, which is the lowest value reported for MOCVD-grown A1GaN/GaN HEMTs on Si featuring the same dimension and structure. The RF characteristics of 0.25-μ m gate length T-shaped gate HEMTs were also investigated.     

InGaN/GaN p-i-n Photodiodes Fabricated with Mg-Doped p-InGaN Layer

Mg-doped p-InGaN layers with In composition of about 10% are grown by metalorganic chemical vapor deposition (MOCVD). The effect of the annealing temperature on the p-type behavior of Mg-doped InGaN is studied. It is found that the hole concentration in p-InGaN increases with a rising annealing temperature in the range of 600-850°C, while the hole mobility remains nearly unchanged until the annealing temperature increases up to 750°C, after which it decreases. On the basis of conductive p-type InGaN growth, the p-In_0.1Ga_0.9N/i-In_0.1Ga_0.9N/n-GaN junction structure is grown and fabricated into photodiodes. The spectral responsivity of the InGaN/GaN p-i-n photodiodes shows that the peak responsivity at zero bias is in the wavelength range 350-400nm.     

Blue emission from InGaN/GaN hexagonal pyramid structures

Cathodoluminescence (CL) from InGaN grown on GaN hexagonal pyramid structures has been investigated. The facet structure can be controlled by the growth temperature and reactor pressure. GaN pyramid structures surrounded with facets were grown at 1020 C at a pressure of 500 Torr by low-pressure metalorganic vapor phase epitaxy (LP-MOVPE). The indium mole fraction in the InGaN film depends on the facet structure. The thickness of the InGaN and the peak wavelength and intensity of the CL from the InGaN gradually increased from the bottom to the top of the facets.     

Performance improvement of blue InGaN light-emitting diodes with a specially designed n-AIGaN hole blocking layer

Blue InGaN light-emitting diodes （LEDs） with a conventional electron blocking layer （EBL）, a common n-A1GaN hole blocking layer （HBL）, and an n-A1GaN HBL with gradual A1 composition are investigated numerically, which involves analyses of the carrier concentration in the active region, energy band diagram, electrostatic field, and internal quantum efficiency （IQE）. The results indicate that LEDs with an n-AIGaN HBL with gradual AI composition exhibit better hole injection efficiency, lower electron leakage, and a smaller electrostatic field in the active region than LEDs with a conven tional p-A1GaN EBL or a common n-A1GaN HBL. Meanwhile, the efficiency droop is alleviated when an n-A1GaN HBL with gradual A1 composition is used.