利用MOCVD在r面蓝宝石上生长的α面GaN中两步AlN缓冲层的优化

采用两步AlN缓冲层(一层低温AlN和一层高温AlN)在r面蓝宝石衬底上生长了非极性的α面GaN,并利用高分辨X射线衍射和光致荧光谱对所生长的材料进行了研究.两步AIN缓冲层在我们之前的工作中已被证明比单步高温AlN或低温GaN缓冲层更有利于减小材料各向异性和提高晶体质量,本文进一步优化了两步AlN缓冲层的结构,并得到了各向异性更小,晶体质量更好的α面GaN薄膜.分析表明,两步AlN缓冲层中的低温AlN层在减小各向异性中起着关键作用.低温AlN层能抑制了优势方向(c轴)的原子迁移,有利于劣势方向(m轴)的原子迁移,从而减小了Al原子在不同方向迁移能力的差异,并为其后的高温AlN缓冲层和GaN层提供"生长模板",以得到各向异性更小、晶体质量更好的α面GaN材料.     

High resolution X-ray diffraction of GaN grown on Si (1 1 1) by MOVPE

High temperature GaN layers have been grown on Si (1 1 1) substrate by metalorganic vapor phase epitaxy (MOVPE). AlN was used as a buffer layer and studied as a function of thickness and growth temperature. The growth was monitored by in situ laser reflectometry. High resolution X-ray diffraction (HRXRD) revealed that optimized monocrystalline GaN was obtained for a 40 nm AlN grown at 1080 °C. This is in good agreement with the results of morphological study by scanning electron microscopy (SEM) and also confirmed by atomic force microscopy (AFM) observations. The best morphology of AlN with columnar structure and lower rms surface roughness is greatly advantageous to the coalescence of the GaN epilayer. Symmetric and asymmetric GaN reflections were combined for twist and stress measurements in monocrystalline GaN. It was found that mosaicity and biaxial tensile stress are still high in 1.7 μm GaN. Curvature radius measurement was also done and correlated to the cracks observations over the GaN surface.     

AlN缓冲层对Si基GaN外延薄膜性质的影响

采用金属有机化合物化学气相沉积（MOCVD）方法制备了不同AlN缓冲层厚度的GaN样品,研究了AlN缓冲层厚度对GaN外延层的应力、表面形貌和晶体质量的影响。研究结果表明：厚度为15 nm的AlN缓冲层不仅可以有效抑制Si扩散,而且还给GaN外延层提供了一个较大的压应力,避免GaN薄膜出现裂纹。在该厚度AlN缓冲层上制备的GaN薄膜表面光亮、无裂纹,受到的张应力为0.3 GPa,（0002）和（1012）面的高分辨X射线衍射摇摆曲线峰值半高宽分别为536 arcsec和594 arcsec,原子力显微镜测试得到表面粗糙度为0.2 nm。     

The influence of AlN/GaN superlattice intermediate layer on the properties of GaN grown on Si（111） substrates

AlN/GaN superlattice buffer is inserted between GaN epitaxial layer and Si substrate before epitaxial growth of GaN layer. High-quality and crack-free GaN epitaxial layers can be obtained by inserting AlN/GaN superlattice buffer layer. The influence of AlN/GaN superlattice buffer layer on the properties of GaN films are investigated in this paper. One of the important roles of the superlattice is to release tensile strain between Si substrate and epilayer. Raman spectra show a substantial decrease of in-plane tensile strain in GaN layers by using AlN/GaN superlattice buffer layer. Moreover, TEM cross-sectional images show that the densities of both screw and edge dislocations are significantly reduced. The GaN films grown on Si with the superlattice buffer also have better surface morphology and optical properties.     

GaN缓冲层对直流反应磁控溅射AlN薄膜的影响(英文)

通过直流磁控反应溅射制备了氮化铝(AlN)薄膜,研究了沉积条件与氮化镓(GaN)缓冲层对薄膜质量的影响。利用X-射线衍射仪(XRD)和扫描电镜(SEM)表征了AlN薄膜的晶体结构和表面形貌。XRD研究结果表明,低工作压强、短靶距和适当的氮气偏压有利于(002)择优取向的AlN薄膜沉积。随着沉积时间的增加,沉积在50 nm厚的GaN缓冲层上的AlN薄膜的(002)面的衍射峰的半高宽急剧减小,而沉积在1μm厚的GaN薄膜上的AlN薄膜的(002)面的衍射峰的半高宽几乎不变。SEM测试结果表明:在沉积的初期,沉积在1μm厚的GaN薄膜上的AlN薄膜的(002)面的晶粒大小分布比沉积在50 nm厚的GaN缓冲层上的AlN薄膜的均匀,而随着沉积时间的增加,它们的晶粒大小分布几乎趋向一致。     

Engineering of nearly strain-free ZnO films on Si(1 1 1) by tuning AlN buffer thickness

ZnO properties were investigated as a function of AlN buffer layer thickness (0–100 nm) in ZnO/AlN/Si(1 1 1) structures grown by metal organic vapor phase epitaxy. A significant improvement of ZnO film crystallinity by tuning AlN buffer thickness was confirmed by x-ray diffraction, topography and photoluminescence measurements. An optimal AlN buffer layer thickness of 50 nm is defined, which allows for growth of nearly strain-free ZnO films. The presence of free excitons at 10 K suggests high crystal quality for all ZnO samples grown on AlN/Si(1 1 1) templates. The intensities of neutral and ionized donor bound exciton lines are found to correlate with the in-plane and out-of-plane strain in the films, respectively.     

利用MOCVD在r面蓝宝石上生长的α面GaN中两步AlN缓冲层的优化

采用两步AlN缓冲层(一层低温AlN和一层高温AlN)在r面蓝宝石衬底上生长了非极性的α面GaN,并利用高分辨X射线衍射和光致荧光谱对所生长的材料进行了研究.两步AIN缓冲层在我们之前的工作中已被证明比单步高温AlN或低温GaN缓冲层更有利于减小材料各向异性和提高晶体质量,本文进一步优化了两步AlN缓冲层的结构,并得到...     

Luminescent properties of GaN films grown on porous silicon substrate

GaN films have been grown on porous silicon at high temperatures (800-1050 °C) by metal organic vapor phase epitaxy. The optical properties of GaN layers were investigated by photoluminescence (PL) and cathodoluminescence (CL) spectroscopy. PL spectra recorded at 5 K exhibit excitonic emissions around 3.36-3.501 eV and a broad yellow luminescence at 2.2 eV. CL analysis at different electron excitation conditions shows spatial non-uniformity in-depth of the yellow and the band-edge emissions. These bands of luminescence are broadened and red- or blue-shifted as the electron beam penetrates in the sample. These behaviors are explained by a change of the fundamental band gap due to residual strain and the local thermal effect. It was found that the use of AlN buffer layer improves the crystalline quality and the luminescence property of GaN.     

Characterization of GaN layers grown on silicon-on-insulator substrates

In this study, we report growth and characterization of GaN layers on (1 0 0)- and (1 1 1)-oriented silicon-on-insulator (SOI) substrates. Using metalorganic chemical vapor deposition (MOCVD) technique, GaN layers are grown on KOH treated Si (1 0 0) overlayers of thin SIMOX SOI substrates. Growth of GaN on such surface with an AlN buffer leads to c-axis orientated textured GaN. This is evident from high-resolution X-ray diffraction (HRXRD) measurement, which shows a much broader rocking curve linewidth. Significantly enhanced photoluminescence (PL) intensity and partial stress relaxation is observed in GaN layers grown on these SOI substrates. Furthermore, GaN grown on (1 1 1)-oriented bonded SOI substrates shows good surface morphology and improved optical quality. Micro-Raman, micro-PL, and HRXRD measurements reveal single crystalline hexagonal GaN oriented along (0 0 0 1) direction. We also report growth and characterization of InGaN/GaN multi-quantum well structures on (1 1 1)-oriented bonded SOI. Such an approach to realize nitride epilayers would be useful to fabricate GaN-based micro-opto-electromechanical systems (MOEMS) and sensors.     

Investigation of etch characteristics of non-polar GaN by wet chemical etching

We characterized the surface defects in a-plane GaN, grown onto r-plane sapphire using a defect-selective etching (DSE) method. The surface morphology of etching pits in a-plane GaN was investigated by using different combination ratios of H₃PO₄ and H₂SO₄ etching media. Different local etching rates between smooth and defect-related surfaces caused variation of the etch pits made by a 1:3 ratio of H₃PO₄/H₂SO₄ etching solution. Analysis results of surface morphology and composition after etching by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) demonstrated that wet chemical etching conditions could show the differences in surface morphology and chemical bonding on the a-plane GaN surface. The etch pits density (EPD) was determined as 3.1 × 10⁸ cm⁻² by atom force microscopy (AFM).     

MOCVD生长Si衬底上HT-AlN缓冲层低生长压力对GaN薄膜的影响

采用金属有机化学气相沉积（MOCVD）技术在Si（111）衬底上外延GaN薄膜,对高温AlN（HT-AlN）缓冲层在小范围内低生长压力（6.7~16.6 kPa）条件下对GaN薄膜特性的影响进行了研究。研究结果表明GaN外延层的表面形貌、结构和光学性质对HT-AlN缓冲层的生长压力有很强的的依赖关系。增加HT-AlN缓冲层的生长压力,GaN薄膜的光学和形貌特性均有明显改善,当HT-AlN缓冲层的生长压力为13.3 kPa时,得到无裂纹的GaN薄膜,其（002）和（102）面的X射线衍射峰值半高宽分别为735 arcsec和778 arcsec,由拉曼光谱计算得到的张应力为0.437 GPa,原子力显微镜（AFM）观测到表面粗糙度为1.57 nm。     

Influence of substrate crystallography on the room temperature synthesis of AlN thin films by reactive sputtering

A pulsed DC reactive ion beam sputtering system has been used to synthesize aluminium nitride (AlN) thin films at room temperature by reactive sputtering. After systematic study of the processing variables, high-quality polycrystalline films with preferred c-axis orientation have been grown successfully on silicon and Au/Si substrates with an Al target under a N₂/(N₂ + Ar) gas flow ratio of 55%, 2 mTorr processing pressure and keeping the temperature of the substrate holder at room temperature. The crystalline quality of the AlN layer as well as the influence of the substrate crystallography on the AlN orientation has been characterized by high-resolution X-ray diffraction (HR-XRD). Best ω-FWHM (Full Width at Half Maximum) values of the (0 0 0 2) reflection rocking curve in the 1 μm thick AlN layers are 1.3°. Atomic Force Microscopy (AFM) measurements have been used to study the surface morphology of the AlN layer and Transmission Electron Microscopy (TEM) measurements to investigate the AlN/substrate interaction. AlN grew off-axis from the Si substrate but on-axis to the surface normal. When the AlN thin film is deposited on top of an Au layer, it grows along the [0 0 0 1] direction but showing a two-domain structure with two in-plane orientations rotated 30° between them.     

Effects of sic buffer layer on the optical properties of ZnO films grown on Si (1 1 1) substrates

ZnO films have been grown by a sol-gel process on Si (1 1 1) substrates with and without SiC buffer layers. The influence of SiC buffer layer on the optical properties of ZnO films grown on Si (1 1 1) substrates was investigated. The intensity of the E₂ (high) phonon peak in the micro-Raman spectrum of ZnO film with the SiC buffer layer is stronger than that of the sample without the SiC buffer layer, and the breadth of E₂ (high) phonon peak of ZnO film with the SiC buffer layer is narrower than that of the sample without the SiC buffer layer. These results indicated that the crystalline quality of the sample with the SiC buffer layer is better than that of the sample without the SiC buffer layer. In photoluminescence spectra, the intensity of free exciton emission from ZnO films with the SiC buffer was much stronger than that from ZnO film without the SiC buffer layer, while the intensity of deep level emission from sample with the SiC buffer layer was about half of that of sample without the SiC buffer layer. The results indicate the SiC buffer layer improves optical qualities of ZnO films on Si (1 1 1) substrates.     

Influence of AlN interfacial layer on electrical properties of high-Al-content Al0.45Ga0.55N/GaN HEMT structure

Unintentionally doped high-Al-content Al_0.45Ga_0.55N/GaN high electron mobility transistor (HEMT) structures with and without AlN interfacial layer were grown by metal-organic chemical vapor deposition (MOCVD) on two-inch sapphire substrates. The effects of AlN interfacial layer on the electrical properties were investigated. At 300 K, high two-dimensional electron gas (2DEG) density of 1.66 × 10¹³ cm⁻² and high electron mobility of 1346 cm² V⁻¹ s⁻¹ were obtained for the high Al content HEMT structure with a 1 nm AlN interfacial layer, consistent with the low average sheet resistance of 287 Ω/sq. The comparison of HEMT wafers with and without AlN interfacial layer shows that high Al content AlGaN/AlN/GaN heterostructures are potential in improving the electrical properties of HEMT structures and the device performances.     

Structural and local electrical properties of AlInN/AlN/GaN heterostructures

GaN layers and Al_1−xIn_xN/AlN/GaN heterostructures have been studied by scanning probe microscopy methods. Threading dislocations (TDs), originating from the GaN (0 0 0 1) layer grown on sapphire, have been investigated. Using Current-Atomic Force Microscopy (C-AFM) TDs have been found to be highly conductive in both GaN and AlInN, while using semi-contact AFM (phase-imaging mode) indium segregation has been traced at TDs in AlInN/AlN/GaN heterostructures. It has been assessed that In segregation is responsible for high conductivity at dislocations in the examined heterostructures.     

Epitaxial growth of Al on Si(1 1 1) with Cu buffer layers

The structure of thin Al films grown on Si(1 1 1) with thin Cu buffer layers has been investigated using synchrotron radiation photoemission spectroscopy. A thin Cu(1 1 1) layer between the Si(1 1 1) substrate and an Al film may enhance quantum well effects in the Al film significantly. The strength of quantum well effects has been investigated qualitatively with respect to the thickness of the Cu buffer layer and to the Al film thickness. Deposition of Cu on Si(1 1 1)7 × 7 leads to formation of a disordered silicide layer in an initial regime before a well-ordered Cu(1 1 1) film is formed after deposition of the equivalent of 6 layers of Cu. In the regime below 6 layers of Cu the disorder is transferred to Al layers subsequently grown on top. The initial growth of up to 8 layers of Al on a well-ordered Si/Cu(1 1 1) layer leads to a disordered film due to the lattice mismatch between the two metals. When the Cu buffer layer and the Al over-layer are above 6 and 8 layers, respectively the Al film shows sharp low energy electron diffraction patterns and very sharp quantum well peaks in the valence band spectra signalling good epitaxial growth.     

Influence of double A1N buffer layers on the qualities of GaN films prepared by metal-organic chemical vapour deposition

<正>In this paper we report that the GaN thin film is grown by metal-organic chemical vapour deposition on a sapphire (0001) substrate with double AlN buffer layers.The buffer layer consists of a low-temperature(LT) AlN layer and a high-temperature(HT) AlN layer that are grown at 600℃and 1000℃,respectively.It is observed that the thickness of the LT-AlN layer drastically influences the quality of GaN thin film,and that the optimized 4.25-min-LT-AlN layer minimizes the dislocation density of GaN thin film.The reason for the improved properties is discussed in this paper.     

Formation of relaxed SiGe on the buffer consists of modified SiGe stacked layers by Si pre-intermixing

High-quality relaxed SiGe films on Si (0 0 1) have been demonstrated with a buffer layer containing modified SiGe (m-SiGe) islands in ultra-high vacuum chemical vapor deposition (UHV/CVD) system. The m-SiGe islands are smoothened by capping an appropriate amount of Si and the subsequent annealing for 10 min. This process leads to the formation of a smooth buffer layer with non-uniform Ge content. With the m-SiGe-dot multilayer as a buffer layer, the 500-nm-thick uniform Si_0.8Ge_0.2 layers were then grown. These m-SiGe islands can serve as effective nucleation centers for misfit dislocations to relax the SiGe overlayer. Surface roughness, strain relaxation, and crystalline quality of the relaxed SiGe overlayer were found to be a function of period's number of the m-SiGe-dot multilayer. By optimizing period number in the buffer, the relaxed Si_0.8Ge_0.2 film on the 10-period m-SiGe-dot multilayer was demonstrated to have a threading dislocation density of 2.0 × 10⁵ cm⁻² and a strain relaxation of 89%.     

Low-temperature MOVPE growth of ZnO thin films by using a buffer layer

ZnO thin films have been grown on a-plane (1,1,−2,0) sapphire substrates by metalorganic vapor phase epitaxy (MOVPE) at low substrate temperature of 350 °C. It is showed that the crystal and electrical quality of the thin films was improved by using a ZnO buffer layer. The photoluminescence (PL) measurements indicate that the ZnO thin films grown at such a low substrate temperature have a strong UV emission.     

Effect of Ⅲ/Ⅴ Ratio of HT-AIN Buffer Layer on Polarity Selection and Electrical Quality of GaN Films Grown by Radio Frequency Molecular Beam Epitaxy

We investigate the effect of A/N ratio of the high temperature （HT） AIN buffer layer on polarity selection and electrical quality of GaN films grown by radio frequency molecular beam epitaxy. The results show that low Al/N ratio results in N-polarity GaN films and intermediate Al/N ratio leads to mixed-polarity GaN films with poor electrical quality. GaN films tend to grow with Ga polarity on Al-rich AIN buffer layers. GaN films with different polarities are confirmed by in-situ reflection high-energy electron diffraction during the growth process. Wet chemical etching, together with atomic force microscopy, also proves the polarity assignments. The optimum value for room-temperature Hall mobility of the Ga-polarity GaN film is 703cm^2/V.s, which is superior to the N-polarity and mixed-polarity GaN films.