界面处理对AlGaN/GaN MIS-HEMTs器件动态特性的影响

研究不同界面处理对AlGaN/GaN金属-绝缘层-半导体(MIS)结构的高电子迁移率晶体管(HEMT)器件性能的影响。采用N_2和NH_3等离子体对器件界面预处理,实验结果表明,N_2等离子体预处理能够减小器件的电流崩塌,通过对N_2等离子体预处理的时间优化,发现预处理时间10 min能够较好地提高器件的动态特性,30 min时动态性能下降。进一步引入AlN作为栅介质插入层并经过高温热退火后能够有效提高器件的动态性能,将器件的阈值回滞从411 mV减小至111 mV,动态测试表明,在900 V关态应力下,器件的电流崩塌因子从42.04减小至4.76。     

具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管（英文）

介绍了一种具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管。采用原子层淀积(ALD)方法实现Al_2O_3栅介质的沉积。槽栅常关型AlGaN/GaN MOS-HEMT的栅长(Lg)为2μm,栅宽(Wg)为0.9 mm(0.45 mm×2),栅极和源极(Lgs)之间的距离为5μm,栅极和漏极(Lgd)之间的距离为10μm。在栅压为-20 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电仅为0.65 nA。在栅压为+12 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电为225 nA。器件的栅压摆幅为-20~+12V。在栅压V_(gs)=+10 V时,槽栅常关型AlGaN/GaN MOS-HEMT电流和饱和电流密度分别达到了98 mA和108 mA/mm(Wg=0.9 mm),特征导通电阻为4 mΩ·cm2。槽栅常关型AlGaN/GaN MOS-HEMT的阈值电压为+4.6 V,开启与关断电流比达到了5×108。当V_(ds)=7 V时,器件的峰值跨导为42 mS/mm(Wg=0.9 mm,V_(gs)=+10 V)。在V_(gs)=0 V时,栅漏间距为10μm的槽栅常关型AlGaN/GaN MOS-HEMT的关断击穿电压为450 V,关断泄露电流为0.025 mA/mm。     

高跨导氢终端多晶金刚石长沟道场效应晶体管特性研究

基于多晶金刚石制作了栅长为4 pm的铝栅氢终端金刚石场效应晶体管.器件的饱和漏源电流为160 mA/mm,导通电阻低达37.85Ω·mm,最大跨导达到32 mS/mm,且跨导高于最大值的90%的栅压(V_(GS))范围达到3 V(-2 V≤V_(GS)≤-5 V).通过传输线电阻分析以及器件的导通电阻和电容-电压特性分析,发现氢终端多晶金刚石栅下沟道中的空穴面浓度达到了1.56×10~(13)cm~(-2),有效迁移率在前述高跨导栅压范围保持在约170 cm~2/(V·s).分析认为,较低的栅源和栅漏串联电阻、沟道中高密度的载流子和在大范围栅压内的高水平迁移率是引起高而宽阔的跨导峰和低导通电阻的原因.     

具有高开启/关断电流比的Al_2O_3/AlGaN/GaN金属氧化物半导体高电子迁移率晶体管（英文）

采用原子层淀积(ALD)方法,制备了Al_2O_3为栅介质的高性能AlG aN/GaN金属氧化物半导体高电子迁移率晶体管(MOS-HEMT)。在栅压为-20 V时,MOS-HEMT的栅漏电比Schottky-gate HEMT的栅漏电低4个数量级以上。在栅压为+2 V时,Schottky-gate HEMT的栅漏电为191μA;在栅压为+20 V时,MOS-HEMT的栅漏电仅为23.6 nA,比同样尺寸的Schottky-gate HEMT的栅漏电低将近7个数量级。AlG aN/GaN MOSHEMT的栅压摆幅达到了±20 V。在栅压Vgs=0 V时,MOS-HEMT的饱和电流密度达到了646 mA/mm,相比Schottky-gate HEMT的饱和电流密度(277 mA/mm)提高了133%。栅漏间距为10μm的AlG aN/GaN MOSHEMT器件在栅压为+3 V时的最大饱和输出电流达到680 mA/mm,特征导通电阻为1.47 mΩ·cm2。Schottky-gate HEMT的开启与关断电流比仅为105,MOS-HEMT的开启与关断电流比超过了109,超出了Schottkygate HEMT器件4个数量级,原因是栅漏电的降低提高了MOS-HEMT的开启与关断电流比。在Vgs=-14 V时,栅漏间距为10μm的AlG aN/GaN MOS-HEMT的关断击穿电压为640 V,关断泄露电流为27μA/mm。     

具有高开启/关断电流比的Al2O3/AlGaN/GaN金属氧化物半导体高电子迁移率晶体管

采用原子层淀积(ALD)方法,制备了Al₂O₃为栅介质的高性能AlGaN/GaN金属氧化物半导体高电子迁移率晶体管(MOS-HEMT)。在栅压为-20 V时,MOS-HEMT的栅漏电比Schottky-gate HEMT的栅漏电低4个数量级以上。在栅压为+2 V时,Schottky-gate HEMT的栅漏电为191μA;在栅压为+20 V时,MOS-HEMT的栅漏电仅为23.6 nA,比同样尺寸的Schottky-gate HEMT的栅漏电低将近7个数量级。AlGaN/GaN MOS-HEMT的栅压摆幅达到了±20 V。在栅压V_gs=0 V时, MOS-HEMT的饱和电流密度达到了646 mA/mm,相比Schottky-gate HEMT的饱和电流密度(277 mA/mm)提高了133%。栅漏间距为10μm的AlGaN/GaN MOS-HEMT器件在栅压为+3 V时的最大饱和输出电流达到680 mA/mm,特征导通电阻为1.47 mΩ·cm²。Schottky-gate HEMT的开启与关断电流比仅为10⁵,MOS-HEMT的开启与关断电流比超过了10⁹,超出了Schottky-gate HEMT器件4个数量级,原因是栅漏电的降低提高了MOS-HEMT的开启与关断电流比。在V_gs=-14 V时,栅漏间距为10μm的AlGaN/GaN MOS-HEMT的关断击穿电压为640 V,关断泄露电流为27μA/mm。     

具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管

介绍了一种具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管。采用原子层淀积(ALD)方法实现Al₂O₃栅介质的沉积。槽栅常关型AlGaN/GaN MOS-HEMT的栅长(L_g)为2 μm,栅宽(W_g)为0.9 mm(0.45 mm×2),栅极和源极(L_gs)之间的距离为5 μm,栅极和漏极(L_gd)之间的距离为10 μm。在栅压为－20 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电仅为0.65 nA。在栅压为+12 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电为225 nA。器件的栅压摆幅为－20~+12 V。在栅压V_gs=+10 V时,槽栅常关型AlGaN/GaN MOS-HEMT电流和饱和电流密度分别达到了98 mA和108 mA/mm (W_g=0.9 mm), 特征导通电阻为4 mΩ·cm²。槽栅常关型AlGaN/GaN MOS-HEMT的阈值电压为+4.6 V,开启与关断电流比达到了5×10⁸。当V_ds=7 V时,器件的峰值跨导为42 mS/mm (W_g=0.9 mm,V_gs=+10 V)。在V_gs=0 V时,栅漏间距为10 μm的槽栅常关型AlGaN/GaN MOS-HEMT的关断击穿电压为450 V,关断泄露电流为0.025 mA/mm。     

ZnO/ZnMgO异质结场效应管的制备与性能研究

利用等离子体增强化学气相沉积(PECVD)技术,在ZnO/ZnMgO异质结构上制备SiO₂作为栅绝缘层,采用光刻与腐蚀工艺制备ZnO/ZnMgO异质结场效应管。电学性能测试及计算结果表明器件栅压调控作用明显。发现栅端漏电流对器件性能造成一定影响。在低温条件下,栅绝缘层产生钝化,从而能够改善器件的性能。     

Al_2O_3薄层修饰SiN_x绝缘层的IGZO-TFTs器件的性能研究

采用原子层沉积工艺(ALD)生长均匀致密的三氧化二铝(Al2O3)薄层对氮化硅(Si Nx)绝缘层进行修饰,研究了铟镓锌氧薄膜晶体管(IGZO-TFTs)器件的性能。当Al2O3修饰层厚度为4 nm时,绝缘层-有源层界面的最大缺陷态密度相比于未修饰器件降低了17.2%,器件性能得到显著改善。场效应迁移率由1.19 cm2/(V·s)提高到7.11 cm2/(V·s),阈值电压由39.70 V降低到25.37 V,1 h正向偏压应力下的阈值电压漂移量由2.19 V减小到1.41 V。     

Al2O3绝缘层的AlGaN/GaN MOSHEMT器件研究

在研制AlGaN/GaN HEMT器件的基础上,采用ALD法制备了Al2O3 AlGaN/GaN MOSHEMT器件.通过X射线光电子能谱测试表明在AlGaN/GaN异质结材料上成功淀积了Al2O3薄膜.根据对HEMT和MOSHEMT器件肖特基电容、器件输出以及转移特性的测试进行分析发现:所制备的Al2O3,薄膜与AlGaN外延层间界面态密度较小,因而MOSHEMT器件呈现出较好的栅控性能;其次,该器件的栅压可以加至 3 V,此时的最大饱和电流达到800 mA/mm,远远高于肖特基栅HEMT器件的最大输出电流;而且栅漏反偏状态下的泄漏电流却减小了两个数量级,提高了器件的击穿电压,通过进一步分析认为泄漏电流主要来源于Fowler-Nordheim隧穿.     

单晶金刚石氢终端场效应晶体管特性

基于微波等离子体化学气相淀积生长的单晶金刚石制作了栅长为2μm的耗尽型氢终端金刚石场效应晶体管,并对器件特性进行了分析.器件的饱和漏电流在栅压为-6 V时达到了96 mA/mm,但是在-6 V时栅泄漏电流过大.在-3.5 V的安全工作栅压下,饱和漏电流达到了77 mA/mm.在器件的饱和区,宽5.9 V的栅电压范围内,跨导随着栅电压的增加而近线性增大到30 mS/mm.通过对器件导通电阻和电容-电压特性的分析,氢终端单晶金刚石的二维空穴气浓度达到了1.99×10~(13)cm~(-2),并且迁移率和载流子浓度均随着栅压向正偏方向的移动而逐渐增大.分析认为,沟道中高密度的载流子、大的栅电容以及迁移率的逐渐增加是引起跨导在很大的栅压范围内近线性增加的原因.     

阶梯AlGaN外延新型Al0.25Ga0.75N/GaNHEMTs器件实验研究

本文报道了作者提出的阶梯AlGaN外延层新型AlGaN/GaN HEMTs结构的实验结果. 实验利用感应耦合等离子体刻蚀(ICP)刻蚀栅边缘的AlGaN外延层, 形成阶梯的AlGaN 外延层结构, 获得浓度分区的沟道2DEG, 使得阶梯AlGaN外延层边缘出现新的电场峰, 有效降低栅边缘的高峰电场, 从而优化了AlGaN/GaN HEMTs器件的表面电场分布. 实验获得了阈值电压-1.5 V的新型AlGaN/GaN HEMTs器件. 经过测试, 同样面积的器件击穿电压从传统结构的67 V提高到新结构的106 V, 提高了58%左右; 脉冲测试下电流崩塌量也比传统结构减少了30%左右, 电流崩塌效应得到了一定的缓解.     

AlGaN/GaN MIS-HEMT using NbAlO dielectric layer grown by atomic layer deposition

We present an AlGaN/GaN metal-insulator-semiconductor high electron mobility transistor (MIS-HEMT) with an NbAlO high-k dielectric deposited by atomic layer deposition (ALD).Surface morphology of samples are observed by atomic force microscopy (AFM),indicating that the ALD NbAlO has an excellent-property surface.Moreover,the sharp transition from depletion to accumulation in capacitance-voltage (C-V)curse of MIS-HEMT demonstrates the high quality bulk and interface properties of NbAlO on AlGaN.The fabricated MIS-HEMT with a gate length of 0.5 μm exhibits a maximum drain current of 960 mA/mm,and the reverse gate leakage current is almost 3 orders of magnitude lower than that of reference HEMT.Based on the improved direct-current operation,the NbAlO can be considered to be a potential gate oxide comparable to other dielectric insulators.     

Ferroelectric effect and equivalent polarization charge model of PbZr_(0.2)Ti_(0.8)O_3 on AlGaN/GaN MIS-HEMT

PbZr_(0.2)Ti_(0.8)O_3(PZT) gate insulator with the thickness of 30 nm is grown by pulsed laser deposition(PLD) in AlGa N/Ga N metal–insulator–semiconductor high electron mobility transistors(MIS-HEMTs). The ferroelectric effect of PZT Al Ga N/Ga N MIS-HEMT is demonstrated. The polarization charge in PZT varies with different gate voltages. The equivalent polarization charge model(EPCM) is proposed for calculating the polarization charge and the concentration of two-dimensional electron gas(2 DEG). The threshold voltage(Vth) and output current density(IDS) can also be obtained by the EPCM. The theoretical values are in good agreement with the experimental results and the model can provide a guide for the design of the PZT MIS-HEMT. The polarization charges of PZT can be modulated by different gate-voltage stresses and the Vthhas a regulation range of 4.0 V. The polarization charge changes after the stress of gate voltage for several seconds. When the gate voltage is stable or changes at high frequency, the output characteristics and the current collapse of the device remain stable.     

具有p-GaN岛状埋层耐压结构的横向AlGaN/GaN高电子迁移率晶体管

GaN基高电子迁移率晶体管(HEMT)相对较低的击穿电压严重限制了其大功率应用.为了进一步改善器件的击穿特性,通过在n-GaN外延缓冲层中引入六个等间距p-GaN岛掩埋缓冲层(PIBL)构成p-n结,提出一种基于p-GaN埋层结构的新型高耐压AlGaN/GaN HEMT器件结构.Sentaurus TCAD仿真结果表明,在关态高漏极电压状态下,p-GaN埋层引入的多个反向p-n结不仅能够有效调制PIBL AlGaN/GaN HEMT的表面电场和体电场分布,而且对于缓冲层泄漏电流有一定的抑制作用,这保证了栅漏间距为10μm的PIBL HEMT能够达到超过1700 V的高击穿电压(BV),是常规结构AlGaN/GaN HEMT击穿电压(580 V)的3倍.同时,PIBL结构AlGaN/GaN HEMT的特征导通电阻仅为1.47 m?·cm~2,因此获得了高达1966 MW·cm~(-2)的品质因数(FOM=BV~2/R_(on,sp)).相比于常规的AlGaN/GaN HEMT,基于新型p-GaN埋岛结构的HEMT器件在保持较低特征导通电阻的同时具有更高的击穿电压,这使得该结构在高功率电力电子器件领域具有很好的应用前景.     

AlGaN/GaN双异质结F注入增强型高电子迁移率晶体管

理论模拟了不同GaN沟道厚度的双异质结(AlGaN/GaN/AlGaN/GaN)材料对高电子迁移率晶体管(HEMT)特性的影响,并模拟了不同F注入剂量下用该材料制作的增强型器件的特性差异.采用双异质结材料,结合F注入工艺成功地研制出了较高正向阈值电压的增强型HEMT器件.实验研究了三种GaN沟道厚度制作的增强型器件直流特性的差异,与模拟结果进行了对比验证.采用降低的F注入等离子体功率,减小了等离子体处理工艺对器件沟道迁移率的损伤,研制出的器件未经高温退火即实现了较高的跨导和饱和电流特性.对14 nm GaN沟道厚度的器件进行了阈值电压温度稳定性和栅泄漏电流的比较研究,并且分析了双异质结器件的漏致势垒降低效应.     

Channel temperature determination of multifinger AlGaN/GaN high electron mobility transistor using micro-Raman technique

Self-heating in multifinger AlGaN/GaN high electron mobility transistor (HEMT) is investigated by micro-Raman spectroscopy. The device temperature is probed on the die as a function of applied bias. The operating temperature of AlGaN/GaN HEMT is estimated from the calibration curve of passively heated AlGaN/GaN structure. A linear increase of junction temperature is observed when direct current dissipated power is increased. When the power dissipation is 12.75 W at a drain voltage of 15 V, a peak temperature of 69.1 ℃ is observed at the gate edge on the drain side of the central finger. The position of the highest temperature corresponds to the high-field region at the gate edge.     

Investigation of passivation effects in AlGaN/GaN metal-insulator-semiconductor high electron-mobility transistor by gate-drain conductance dispersion study

This paper studies the drain current collapse of AlGaN/GaN metal-insulator-semiconductor high electron-mobility transistors (MIS-HEMTs) with NbAlO dielectric by applying dual-pulsed stress to the gate and drain of the device.For NbAlO MIS-HEMT,smaller current collapse is found,especially when the gate static voltage is 8 V.Through a thorough study of the gate-drain conductance dispersion,it is found that the growth of NbAlO can reduce the trap density of the AlGaN surface.Therefore,fewer traps can be filled by gate electrons,and hence the depletion effect in the channel is suppressed effectively.It is proved that the NbAlO gate dielectric can not only decrease gate leakage current but also passivate the AlGaN surface effectively,and weaken the current collapse effect accordingly.     

High linearity AlGaN/GaN HEMT with double-Vth coupling for millimeter-wave applications

We demonstrated an AlGaN/GaN high electron mobility transistor(HEMT)namely double-Vthcoupling HEMT(DVC-HEMT)fabricated by connecting different threshold voltage(Vth)values including the slant recess element and planar element in parallel along the gate width with N;O plasma treatment on the gate region.The comparative studies of DVC-HEMT and Fin-like HEMT fabricated on the same wafer show significantly improved linearity of transconductance(Gm)and radio frequency(RF)output signal characteristics in DVC-HEMT.The fabricated device shows the transconductance plateau larger than 7 V,which yields a flattened fT/fmax-gate bias dependence.At the operating frequency of 30 GHz,the peak power-added efficiency(PAE)of 41%accompanied by the power density(Pout)of 5.3 W/mm.Furthermore,the proposed architecture also features an exceptional linearity performance with 1-d B compression point(P1 d B)of 28 d Bm,whereas that of the Fin-like HEMT is 25.2 d Bm.The device demonstrated in this article has great potential to be a new paradigm for millimeter-wave application where high linearity is essential.     

阶梯AlGaN外延新型Al_(0.25)Ga_(0.75)N/GaNHEMTs击穿特性分析

为了优化AlGaN/GaN HEMTs器件表面电场,提高击穿电压,本文首次提出了一种新型阶梯AlGaN/GaN HEMTs结构.新结构利用AlGaN/GaN异质结形成的2DEG浓度随外延AlGaN层厚度降低而减小的规律,通过减薄靠近栅边缘外延的AlGaN层,使沟道2DEG浓度分区,形成栅边缘低浓度2DEG区,低的2DEG使阶梯AlGaN交界出现新的电场峰,新电场峰的出现有效降低了栅边缘的高峰电场,优化了AlGaN/GaN HEMTs器件的表面电场分布,使器件击穿电压从传统结构的446 V,提高到新结构的640 V.为了获得与实际测试结果一致的击穿曲线,本文在GaN缓冲层中设定了一定浓度的受主型缺陷,通过仿真分析验证了国际上外延GaN缓冲层时掺入受主型离子的原因,并通过仿真分析获得了与实际测试结果一致的击穿曲线.