基于蒙特卡洛和器件仿真的单粒子翻转计算方法

文章提出了一种基于蒙特卡洛和器件仿真的存储器单粒子翻转截面获取方法,可以准确计算存储器单粒子效应,并定位单粒子翻转的灵敏区域.基于该方法,计算了国产静态存储器和现场可编程门阵列(FPGA)存储区的单粒子效应的截面数据,仿真结果和重离子单粒子效应试验结果符合较好.仿真计算揭示了器件单粒子翻转敏感程度与器件n,p截止管区域面积相关的物理机理,并获得了不同线性能量转移(LET)值下单粒子翻转灵敏区域分布.采用蒙特卡洛方法计算了具有相同LET、不同能量的离子径迹分布,结果显示高能离子的电离径迹半径远大于低能离子,而低能离子径迹中心的能量密度却要高约两到三个数量级.随着器件特征尺寸的减小,这种差别的影响将会越来越明显,阈值LET和饱和截面将不能完全描述器件单粒子效应结果.     

各向异性静态随机存储器中的多位翻转分析研究

重离子实验结果表明,具有高线性能量转移(LET)或大角度入射的快重离子导致静态随机存储器(SRAM)中的多位翻转(MBU)比例增大,甚至超过单位翻转比例。单个离子径迹中的电荷可以沿着径向扩散数个微米,被临近的灵敏区收集后引起MBU。器件灵敏区的各向异性空间布局与离子入射方向共同影响测试器件的MBU图形特征。位线接触点的纵向隔离导致横向型成为主要的两位翻转图形;"L"型和"田"型分别是主要的三位翻转和四位翻转图形。最后,对SRAM抗MBU加固设计和实验验证方法进行了讨论。     

Simulation of temporal characteristics of ion-velocity susceptibility to single event upset effect

Using a Monte Carlo simulation tool of the multi-functional package for SEEs Analysis(MUFPSA), we study the temporal characteristics of ion-velocity susceptibility to the single event upset(SEU) effect, including the deposited energy,traversed time within the device, and profile of the current pulse. The results show that the averaged dposited energy decreases with the increase of the ion-velocity, and incident ions of209 Bi have a wider distribution of energy deposition than132 Xe at the same ion-velocity. Additionally, the traversed time presents an obvious decreasing trend with the increase of ion-velocity. Concurrently, ion-velocity certainly has an influence on the current pulse and then it presents a particular regularity. The detailed discussion is conducted to estimate the relevant linear energy transfer(LET) of incident ions and the SEU cross section of the testing device from experiment and simulation and to critically consider the metric of LET.     

空间高能离子在纳米级SOI SRAM中引起的单粒子翻转特性及物理机理研究

基于蒙特卡罗方法研究空间高能离子在65—32 nm绝缘体上硅静态随机存取存储器(SOI SRAM)中产生的灵敏区沉积能量谱、单粒子翻转截面和空间错误率特性及内在的物理机理.结果表明:单核能为200 MeV/n的空间离子在60—40 nm厚的灵敏区中产生的能损歧离导致纳米级SOI SRAM在亚线性能量转移阈值区域出现单粒子翻转;宽的二次电子分布导致灵敏区仅能部分收集单个高能离子径迹中的电子-空穴对,致使灵敏区最大和平均沉积能量各下降25%和33.3%,进而引起单粒子翻转概率降低,以及在轨错误率下降约80%.发现俘获带质子直接电离作用导致65 nm SOI SRAM的在轨错误率增大一到两个数量级.     

FPGA配置片反熔丝PROMs加速器地面单粒子效应特性研究

针对0.13 μm CMOS（Complementary Metal-Oxide-Semiconductor）体硅外延工艺下FPGA（Field Programmable Gate Arrays）配置片反熔丝PROM（Programmable-Read-Only-Memory）进行了单粒子效应（Single Event Effects SEEs）的加速器地面模拟试验研究。以PROM的存储容量、数据类型和工艺差异性为研究变量,考核与验证其在不同种类和能量粒子入射的系列性加速器地面SEEs模拟试验。研究结果表明,相对于8 Mbits PROM而言,空片16 Mbits PROM抗辐射性能最优,且从翻转饱和截面上说,16 Mbits的PROM具备更高的可靠性,优于国外同系列的芯片类型,试验用PROM芯片的单粒子锁定阈值>99.0 MeV·cm2/mg。另一方面,研究0.13 μm CMOS普通与深阱工艺技术下PROM芯片单粒子翻转效应异同性的实验数据表明,在高LET（Linear Energy Transfer）处的两者抗辐射性能并无明显变化,但是低LET处（LET翻转阈值）的加固效果较为明显,即抗辐射技术能力主要体现在LET翻转阈值的提升而非翻转截面的减小。Single event effects (SEEs) have been characterized and investigated on one-time configured devices for field-programmable-gate-arrays (FPGA) of programmable-read-only-memory (PROM) in 0.13 μm Complementary Metal-Oxide-Semiconductor (CMOS) technology.The variables of their memory size,written data and technology have been taken into consideration as the key parameters affecting the SEEs sensitivity when testing and verifying the reliability/radiation tolerance on self-made PROMs by heavy ions.The results show that,16 Mbits PROM within blanked data has been studied that it has better performance to radiation tolerance as compared with the 8 Mbits PROMs.Additionally,16 Mbits PROMs have the higher reliability,if based on the viewpoint of the saturated single event upset cross-section.To the single event latchup,16 Mbits PROMs were exposed to a total fluence of 107 ions/cm2 at the linear energy transfer (LET) of 99.0 MeV·cm2/mg and no obvious fluctuation of current has been observed.Additionally,as comparing the zone of high LET value,0.13 μm CMOS transistors with deep-well technology present a better radiation hardened approach than normal technology,especially in improving the threshold of LET at the zone of low LET value.     

重离子在14-nm FinFET SRAM器件引起的单粒子翻转

通过重离子实验研究了14-nm FinFET工艺静态随机存取存储器(SRAM)的单粒子翻转(SEU)特性。通过使用Weibull函数拟合SEU截面获得该器件的线性能量转移(LET)阈值:0.1 MeV/(mg/cm2)。对多位翻转(MBU)贡献的统计结果表明,当LET等于40.3 MeV/(mg/cm2)时,MBU的占比超过95%。此外,FinFET SRAM的SEU截面呈现出与Fin相关的入射角度的各向异性。该研究对基于FinFET工艺的抗辐射CMOS集成电路(IC)的设计具有一定的指导作用。     

252Cf源和重离子加速器对FPGA的单粒子效应

 对10万门基于静态随机存储器的现场可编程门阵列（FPGA）分别在锎-252（²⁵²Cf）源和HI-13串列加速器下进行了单粒子效应试验研究,测试了静态单粒子翻转截面及发生单粒子闩锁的线性能量转移阈值,并对试验结果进行了等效性分析比较。试验结果表明²⁵²Cf源引起的FPGA单粒子翻转截面比重离子加速器引起的约低1个数量级;使用²⁵²Cf源未能观测到该器件的单粒子闩锁现象,而使用重离子加速器可以测出该FPGA发生单粒子闩锁的线性能量转移阈值;在现代集成电路的宇航辐射效应地面模拟单粒子效应试验中²⁵²Cf源不是理想的测试单粒子闩锁的辐射源。     

利用加速器重离子进行SRAM单粒子效应研究

 报导了利用北京大学串列静电加速器提供的重离子对两类静态随机存储器进行单粒子效应的实验和测量。给出了两类静态随机存储器的单粒子效应翻转截面随线性能量转移值的变化关系曲线。     

Discussion of the metric in characterizing single-event effect induced by heavy ions

Single-event effect (SEE) is the most serious problem in space environment. The modern semiconductor technology worries about the feasibility of the linear energy transfer (LET) as metric in characterizing SEE induced by heavy ions. In the paper, we calibrate the detailed static random access memory (SRAM) cell structure model of advanced field programmable gate array (FPGA) device using the computer-aided design tool, and calculate the heavy ion energy loss in multi-layer metal utilizing Geant4. Based on the heavy ion accelerator experiment and numerical simulation, it is proved that the metric of LET at the device surface, with ignoring the top metal material in advanced semiconductor device, would underestimate the SEE. In the SEE evaluation in space radiation environment the top-layers on the semiconductor device must be taken into consideration.     

Discussion of the metric in characterizing the single-event effect induced by heavy ions

The single-event effect(SEE) is the most serious problem in space environment.The modern semiconductor technology is concerned with the feasibility of the linear energy transfer(LET) as metric in characterizing SEE induced by heavy ions.In this paper,we calibrate the detailed static random access memory(SRAM) cell structure model of an advanced field programmable gate array(FPGA) device using the computer-aided design tool,and calculate the heavy ion energy loss in multi-layer metal utilizing Geant4.Based on the heavy ion accelerator experiment and numerical simulation,it is proved that the metric of LET at the device surface,ignoring the top metal material in the advanced semiconductor device,would underestimate the SEE.In the SEE evaluation in space radiation environment the top-layers on the semiconductor device must be taken into consideration.     

Recovery of single event upset in advanced complementary metalben oxide semiconductor static random access memory cells

Using computer-aided design three-dimensional (3D) simulation technology, the recovery mechanism of single event upset and the effects of spacing and hit angle on the recovery are studied. It is found that the multi-node charge collection plays a key role in recovery and shielding the charge sharing by adding guard rings. It cannot exhibit the recovery effect. It is also indicated that the upset linear energy transfer (LET) threshold is kept constant while the recovery LET threshold increases as the spacing increases. Additionally, the effect of incident angle on recovery is analysed and it is shown that a larger angle can bring about a stronger charge sharing effect, thus strengthening the recovery ability.     

纳米DDR SRAM器件重离子单粒子效应试验研究

针对90 nm和65 nm DDR（双倍数率）SRAM器件,开展与纳米尺度SRAM单粒子效应相关性的试验研究。分析了特征尺寸、测试图形、离子入射角度、工作电压等不同试验条件对单粒子翻转（SEU）的影响和效应规律,并对现有试验方法的可行性进行了分析。研究表明:特征尺寸减小导致翻转截面降低,测试图形和工作电压对器件单粒子翻转截面影响不大;随着入射角度增加,多位翻转的增加导致器件SEU截面有所增大;余弦倾角的试验方法对于纳米器件的适用性与离子种类和线性能量转移（LET）值相关,具有很大的局限性。     

High capacity production of >65% spin polarized xenon-129 for NMR spectroscopy and imaging

A rubidium spin exchange optical pumping system for high capacity production of >65% spin polarized 129Xe gas is described. This system is based on a fiber coupled multiple laser diode array capable of producing an unprecedented 210 W of circularly polarized light at the pumping cell with a laser line width of 1.6 nm. The 129Xe nuclear spin polarization is measured as a function of flow rate, pumping cell pressure, and laser power for varying pumping gas compositions. A maximum 129Xe nuclear polarization of 67% was achieved using a 0.6% Xe mixture at a Xe flow rate of 2.45 sccm. The ability to generate 12% polarized 129Xe at rates in excess of 1L-atm/h is also demonstrated. To achieve production of 129Xe gas at even higher polarization will rely on further optimization of the pumping cell and laser beam geometries in order to mitigate problems associated with temperature gradients that are encountered at high laser power and Rb density.     

Interdependence of in-cell xenon density and temperature during Rb/129Xe spin-exchange optical pumping using VHG-narrowed laser diode arrays

The (129)Xe nuclear spin polarization (P(Xe)) that can be achieved via spin-exchange optical pumping (SEOP) is typically limited at high in-cell xenon densities ([Xe](cell)), due primarily to corresponding reductions in the alkali metal electron spin polarization (e.g. P(Rb)) caused by increased non-spin-conserving Rb-Xe collisions. While demonstrating the utility of volume holographic grating (VHG)-narrowed lasers for Rb/(129)Xe SEOP, we recently reported [P. Nikolaou et al., JMR 197 (2009) 249] an anomalous dependence of the observed P(Xe) on the in-cell xenon partial pressure (p(Xe)), wherein P(Xe) values were abnormally low at decreased p(Xe), peaked at moderate p(Xe) (~300 torr), and remained surprisingly elevated at relatively high p(Xe) values (>1000 torr). Using in situ low-field (129)Xe NMR, it is shown that the above effects result from an unexpected, inverse relationship between the xenon partial pressure and the optimal cell temperature (T(OPT)) for Rb/(129)Xe SEOP. This interdependence appears to result directly from changes in the efficiency of one or more components of the Rb/(129)Xe SEOP process, and can be exploited to achieve improved P(Xe) with relatively high xenon densities measured at high field (including averaged P(Xe) values of ~52%, ~31%, ~22%, and ~11% at 50, 300, 500, and 2000 torr, respectively).     

Oscillator strengths and lifetimes calculated by the Dirac-Fock method for the levels of ions of the cesium isoelectronic sequence

A new method of data transmission in DWDM systems along existing long-distance fiber-optic communication lines is proposed. The existing method, e.g., uses 32 wavelengths in the NRZ code with an average power of 16 conventional units (16 units and 16 zeros on the average) and transmission of 32 bits/cycle. In the new method, one of 124 wavelengths with a duration of one cycle each (at any time instant, no more than 16 obligatory different wavelengths) and capacity of 4 bits with an average power of 15 conventional units and rate of 64 bits/cycle is transmitted at every instant of a 1/16 cycle. The cross modulation and double Rayleigh scattering are significantly decreased owing to uniform distribution of power over time at different wavelengths. The time redundancy (forward error correction (FEC)) is about 7% and allows one to achieve a coding enhancement of about 6 dB by detecting and removing deletions and errors simultaneously.     

The characteristic spectral lines of target atoms in the impact of ~(40)Ar~(q+) ions on metal surfaces

1 Introduction It has been found that a large number of ions and atoms can be sputtered; and elec-trons and X-ray can be emitted in the impact of slow highly charged ions (SHCI) onmetal surfaces. It has also been shown that a slow highly charged ion can deposit anamount of potential energy ranging from tens to hundreds of keV within a nanometer-sized volume on femtosecond time scale during impinging on a solid surface. Theequivalent power density is about 1014 W/cm2 and bombardment craters …     

Human Pulmonary Hyperpolarized ~(129)Xe MRI: a Preliminary Study

We study the feasibility and safety of human lung hyperpolarized(HP)~(129)Xe magnetic resonance imaging(MRI).There is no significant change in physiological parameters before and after the examinations of all subjects.Compared with computed tomography, HP~(129)Xe MRI is sensitive to earlier and smaller ventilation defects. The distribution of the HP~(129)Xe MRI signal reflects the pulmonary compliance with the gravity gradient. This is the first application of HP~(129)Xe MRI ventilation imaging in China, and this technology is expected to provide more useful information for clinical practice.     

The impact of scaling on single event upset in 6T and 12T SRAMs from 130 to 22 nm CMOS technology

ABSTRACT

As transistor sizes scale down to nanometres dimensions, CMOS circuits become more sensitive to radiation. High-performance static random access memory (SRAM) cells are prone to radiation-induced single event upsets (SEU) which come from the natural space environment. The SEU generates a soft error in the transistor due to the strike of an ionizing particle. Thus, this paper compares the endurance of 12T SRAM and 6T SRAM circuit on 130 up to 22?nm CMOS technology towards SEU. Besides that, this paper discusses the trend of critical linear energy transfer (LET) and collected charge due to technology scaling for the respective circuit. The critical LET (LETcrit) and critical charge (Qcrit) of 6T are approximately 50% lower compared with 12T SRAMs.     

重离子核反应对单粒子翻转的影响（英文）

LET作为一个传统的工程参量,并不能完全满足单粒子翻转数据表征的需要,而且也不能直接地反映核反应的一些特性(包括核反应概率与次级粒子),因此研究了重离子与器件作用过程中核反应对单粒子翻转的影响。基于蒙特卡罗模拟与深入的分析,本研究对比了在直接电离与考虑核反应两种模式下的模拟结果。在模拟中,利用不同的重离子表征了核反应在单粒子翻转发生中所起的作用。结果显示,核反应对单粒子翻转截面的贡献依赖于离子的能量,并呈现非单调的变化关系。基于模拟的结果,建议用重离子核反应引起单粒子翻转的最恶劣情况来预估空间单粒子翻转率。     

Observation of hyperfine mixing in measurements of a magnetic octupole decay in isotopically pure nickel-like 129Xe and 132Xe ions

We present measurements of high statistical significance of the rate of the magnetic octupole (M3 ) decay in nickel-like ions of isotopically pure 129Xe and 132Xe. On 132Xe, an isotope with zero nuclear spin and therefore without hyperfine structure, the lifetime of the metastable level was established as (15.06+/-0.24) ms. On 129Xe, an additional fast (2.7+/-0.1 ms) decay component was established that represents hyperfine mixing with a level that decays by electric quadrupole (E2 ) radiation.