溶液法铝诱导晶化制备多晶硅薄膜

采用铝（Al）盐溶液作为诱导源进行了非晶硅晶化成多晶硅的研究.光学显微镜观测与Raman光谱分析表明,合适配比的铝盐溶液能够将非晶硅予以诱导晶化.采用剥层XPS测试分析,探究了Al盐溶液与硅表面可能的化学反应以及随之发生的硅-铝层交换的过程.最后对溶液法诱导晶化的机理进行了讨论. 关键词： 铝诱导晶化 多晶硅薄膜 溶液法     

脉冲激光晶化超薄非晶硅膜的分子动力学研究

利用准分子脉冲激光晶化非晶硅薄膜是制备高密度尺寸可控的硅基纳米结构的有效方法之一.本文将脉冲激光对非晶硅超薄膜的影响处理为热传导问题,采用了基于Tersoff势函数的分子动力学方法模拟了在非晶氮化硅衬底上2.7 nm超薄非晶硅膜的脉冲激光晶化过程.研究了不同激光能量对非晶硅薄膜晶化形成纳米硅的影响,发现在合适的激光能量窗口下,可以获得高密度尺寸可控的纳米硅薄膜,进而模拟了在此能量作用下非晶硅膜中成核与生长的机理与微观过程,并对晶化所获得的纳米硅薄膜的微结构进行了分析. 关键词： 非晶硅 分子动力学 脉冲激光晶化     

488nm连续激光晶化本征非晶硅薄膜的喇曼光谱研究

利用等离子增强化学气相沉积系统制备了本征非晶硅薄膜,并选用488 nm波长的连续激光进行晶化.采用喇曼测试技术对本征非晶硅薄膜在不同激光功率密度和扫描时间下的晶化状态进行了表征,并用514 nm波长与488 nm波长对样品的晶化效果进行了比较.测试结果显示:激光照射时间60 s,激光功率密度在1.57×105 W/cm...     

氢退火的BZO前电极对非晶硅薄膜太阳能电池性能的影响

采用低压化学气相沉积方法在玻璃衬底上制备了B掺杂的ZnO（BZO）薄膜,通过氢退火对BZO进行处理,然后作为前电极进行了非晶硅薄膜太阳能电池的制备及性能研究。结果表明：在氢气气氛下退火后,BZO薄膜的载流子浓度基本无变化,但Hall迁移率显著提高,这使得BZO薄膜的导电能力提高;当采用厚度较小、透光率较高的BZO薄膜进行氢退火后作为前电极结构时,非晶硅薄膜太阳能电池的短路电流密度提高0.3~0.4 mA/cm²,电池的转化效率提高0.2%。实验结果可为通过优化前电极结构来提高非晶硅薄膜太阳能电池转化效率提供一种简易的方法。     

重掺杂AZO透明导电薄膜的光电特性

以Al质量分数为2%的ZnO陶瓷靶为靶材,在氧气气氛中,采用脉冲激光沉积方法(PLD)在石英衬底表面生长了重掺杂的ZnO:Al(AZO)薄膜.通过X射线衍射仪、紫外可见分光光度计、微区拉曼光谱仪、霍尔测量仪对合成薄膜材料的晶体结构、光学、电学性质等进行了研究.结果表明:所制备的AZO薄膜呈现具有高度c轴择优取向的ZnO...     

532nm连续激光晶化非晶硅薄膜的原位拉曼光谱研究

用磁控溅射制备了非晶硅薄膜,用波长为532 nm的连续激光退火和显微Raman光谱原位测试技术和场发射扫描电子显微镜研究了非晶硅薄膜在不同激光功率密度和不同扫描速度下的晶化状态。结果表明,激光照射时间10 s,激光功率密度大于2.929×105W/cm2时,能实现非晶硅薄膜晶化。在激光功率密度为5.093×105W/cm2,扫描速度为10 mm/s时非晶硅开始向多晶硅转化。在5.093×105W/cm2的功率密度下,以1.0 mm/s的扫描速度退火非晶硅薄膜,得到的晶粒直径为740 nm。     

ZnO薄膜的激光辐照效应研究

研究了KrF准分子激光辐照对ZnO薄膜的本征缺陷.紫外（UV）发光以及表面形貌的影响,并对室温下ZnO的UV发射机理进行了详细探讨.结果表明激光辐照打断了薄膜内Zn—O键,氧空位（锌填隙）增多,导致表面电阻率下降,载流子浓度升高,调节激光辐照能量密度,可在较大范围内调控ZnO薄膜中的施主缺陷浓度;同时在激光热效应作用下,薄膜晶粒熔融长大,表面粗糙度大大降低;室温下ZnO薄膜的UV发光包括自由激子复合发光（FX）及其声子伴线（FX-LO）,缺陷浓度决定了FX与FX-LO的相对强度比,进而影响UV发射峰的强度以及位置.因此,激光辐照可以快速、有效地对ZnO薄膜内的缺陷浓度进行调控,从而控制其室温下的UV发射强度,这对于提高ZnO基光电器件的性能具有重要意义. 关键词： ZnO薄膜 激光辐照 紫外发光 缺陷浓度     

H/Al共掺杂对ZnO基透明导电薄膜光电性质和晶体结构的影响

利用H在ZnO中作为浅施主杂质的特性,研究了H掺杂对ZnO：Al透明导电薄膜特性的影响。通过降低ZnO：Al中Al的含量并同时引入H掺杂,解决了透明导电薄膜中高导电性与高透过率之间的矛盾。H的掺杂可以显著降低ZnO基透明导电薄膜的电阻率,这是由于H一方面作为施主可以提供电子从而提高了自由载流子浓度;另一方面与ZnO晶界中的O^-结合降低了晶界势垒,提高了载流子迁移率。利用H掺杂,可以在Al掺杂量降低10倍的情况下,仍然能获得低电阻率（6.3×10^-4 Ω·cm）的透明导电薄膜,同时其近红外波段（1 200 nm）透光率从64%提高到90%。这种具有高导电性和高透光性的透明导电薄膜可以应用于各类薄膜太阳能电池中以提升器件效率。     

磁控共溅射低温制备多晶硅薄膜及其特性研究

多晶硅在光电子器件领域具有较为重要的用途。利用磁控溅射镀膜系统,通过共溅射技术在玻璃衬底上制备了非晶硅铝(α-Si/Al)复合膜,将Al原子团包覆在α-Si基质中,膜中的Al含量可通过Al和Si的溅射功率比来调节。复合膜于N₂气氛中进行350 ℃,10 min快速退火处理,制备出了多晶硅薄膜。利用X射线衍射仪、拉曼光谱仪和紫外-可见光-近红外分光光度计对多晶硅薄膜的性能进行表征,研究了Al含量对多晶硅薄膜性能的影响。结果表明：共溅射法制备的α-Si/Al复合膜在低温光热退火下晶化为晶粒分布均匀的多晶硅薄膜;随着膜中Al含量逐渐增加,多晶硅薄膜的晶化率、晶粒尺寸逐渐增加,带隙则逐渐降低;Al/Si溅射功率比为0.1时可获得纳米晶硅薄膜,Al/Si溅射功率比为0.3时得到晶化率较高的多晶硅薄膜,通过Al含量的调节可实现多晶硅薄膜的晶化率、晶粒尺寸及带隙的可控。     

488 nm连续激光晶化本征非晶硅薄膜的喇曼光谱研究

利用等离子增强化学气相沉积系统制备了本征非晶硅薄膜,并选用488 nm波长的连续激光进行晶化.采用喇曼测试技术对本征非晶硅薄膜在不同激光功率密度和扫描时间下的晶化状态进行了表征,并用514 nm波长与488 nm波长对样品的晶化效果进行了比较.测试结果显示:激光照射时间60 s, 激光功率密度在1.57×10⁵ W/cm²时,能实现非晶硅向多晶硅的转变,在功率密度达到2.7 56×10⁵ W/cm²时,有非晶开始向单晶转变,随着激光功率密度的继续增加,晶化结果仍为单晶;在功率密度为2.362×10⁵ W/cm²下,60 s照射时间晶化效果较好;在功率密度为2.756×10⁵ W/cm²和照射时间为60 s的条件下,用488 nm波长比514 nm波长的激光晶化本征非晶硅薄膜效果较好,并均为单晶态.     

真空条件下不同波长固体激光烧蚀单晶硅的实验研究

通过倍频Nd：YAG固体激光的基波得到波长分别为532、355和266 nm的激光,研究了单晶硅（Si）对不同波长固体激光的吸收规律和3种不同波长激光在真空条件下烧蚀单晶Si的烧蚀特征。结果表明,单晶Si对波长为100~370 nm的紫外激光具有很好的吸收效果;在其他条件相同时,532 nm波长激光烧蚀单晶Si所需最低单脉冲能量（Ep=30 μJ）是355和266 nm波长激光烧蚀单晶Si所需最低单脉冲能量（Ep=15 μJ）的2倍;532、355和266 nm的激光烧蚀单晶Si的烧蚀阈值随着波长的变短而变小。     

Dopant-dependence of one-step metal-induced dopant activation process in silicon

We investigate dopant-dependence of low temperature dopant activation technique in α-Si featuring one-step metal-induced crystallization (MIC) to decrease resistivity of p⁺ and n⁺ Si films by forming Ni_xSi_y. Ni not only crystallizes p-type α-Si film but also facilitates activation of boron atoms in the α-Si during the crystallization at 500 °C. However, phosphorus atoms are poorly activated because of the suppressed Ni-MIC rate in n-type α-Si. Finally, p⁺/n and n⁺/p junction diodes are demonstrated on single crystalline Si substrates by the low temperature dopant activation technique promising for high performance TFTs as well as transistors with an elevated S/D.     

Characterization of laser-ablated and chemically reduced silver colloids in aqueous solution by UV/VIS spectroscopy and STM/SEM microscopy

Silver colloids in aqueous solution were studied by different scanning microscopy techniques and UV/VIS spectroscopy. The silver colloids were produced either by chemical reduction or by nanosecond laser ablation from a solid silver foil in water. Variation of laser power and ablation time leads to solutions of metal clusters of different sizes in water. We characterized the electronic absorption of the clusters by UV/VIS spectroscopy. STM (scanning tunneling microscope) imaging of the metal colloids shows atomic resolution of rod- or tenon-like silver clusters up to 10-nm length formed by laser ablation. Our scanning electron microscope measurements, however, show that much larger silver colloids up to 5-μm length are also formed, which are not visible in the STM due to their roughness. We correlate them with the long-wavelength tail of the multimodal UV/VIS spectrum. The silver colloids obtained by chemical reduction are generally larger and their electronic spectra are red-shifted compared to the laser-ablated clusters. Irradiation of the colloid solution with nanosecond laser pulses of appropriate fluence at 532 nm and 355 nm initially reduced the colloid size. Longer irradiation at 355 nm, however, leads to the formation of larger colloids again. There seems to be a critical lower particle size, where silver clusters in aqueous solution become unstable and start to coagulate. Received: 24 June 2002 / Revised version: 25 July 2002 / Published online: 25 October 2002 RID="*" ID="*"This work is part of the thesis of H. M?ltgen RID="**" ID="**"Corresponding author. Fax: +49-211/811-5195, E-mail: kleinermanns@uni-duesseldorf.de     

The effect of laser wavelength on the ablation rate of carbon

The ablation of graphite is studied as a function of laser fluence for 355, 532 and 1,064 nm wavelength generated by a nanosecond Nd:YAG laser. It has been found that in the case of lower wavelengths, the transition from the thermal ablation to the phase explosion takes place at lower laser fluences. The change of crater shape due to the effect of deep drilling in the proximity of the phase explosion threshold was observed. The calculations of plasma radiation flux to the target surface were made, and the considerable increase of absorbed energy density was found in the case of 355 nm wavelength.     

低温铝诱导晶化制备纳米晶硅薄膜的物相和光学性能研究

采用射频磁控溅射镀膜系统,在玻璃衬底上制备了非晶硅(α-Si)/铝(Al)复合薄膜,结合氮气(N₂)气氛中低温快速光热退火制备了纳米晶硅(nc-Si)薄膜;利用光学显微镜、共焦光学显微仪、X射线衍射(XRD)仪、拉曼散射光谱(Raman)仪和紫外-可见光-近红外分光光度计(UV-VIS-NIR)对纳米晶硅薄膜的表面形貌、物相及光学性能进行了表征,研究了退火工艺对薄膜性能的影响。结果表明： 300 ℃,25 min光热退火可使α-Si/Al膜晶化为纳米晶硅薄膜,晶化率为15.56%,晶粒尺寸为1.75 nm;退火温度从300 ℃逐渐升高到400 ℃,纳米晶硅薄膜晶粒尺寸、晶化率、带隙逐渐增加,表面均匀性、晶格畸变量逐渐减小;退火温度从400 ℃逐渐升高到500 ℃,纳米晶硅薄膜的晶粒尺寸、晶化率继续增加,带隙则逐渐降低;采用纳米晶硅薄膜的吸光模型验证了所制备的纳米晶硅薄膜的光学特性,其光学带隙的变化趋势与吸光模型得出的结果一致。     

Laser scribing of gallium doped zinc oxide thin films using picosecond laser

We report on a comprehensive study of picosecond laser scribing of gallium doped zinc oxide (GZO) thin films deposited on glass substrates using 355 nm, 532 nm and 1064 nm radiation, respectively. In this study, we investigated the influence of front side and rear side irradiation and determined single pulse ablation thresholds for all three wavelengths. Good ablation quality with full electrical isolation, steep groove walls and a smooth groove bottom was achieved by 355 nm rear side processing with a scanning speed of 224 mm/s. Ridges at the groove rims were found to be between 15 nm and 45 nm high. At similar scanning speed, laser scribing using 532 nm and 1064 nm radiation resulted in a lower ablation quality due to a higher roughness of the groove bottoms or higher ridges at the groove rims.     

343 nm飞秒激光制备微孔阵列以增强聚氨酯合成革透湿性

为了提高聚氨酯(PU)合成革透湿性,分别使用343 nm飞秒激光和作为对比的1030 nm飞秒激光及1064 nm纳秒激光制备微孔阵列。采用扫描电镜(SEM)和3D激光扫描显微镜对比研究了微孔形貌。结果表明,343 nm飞秒激光可以制备出效果最佳的微孔。此外,分析了3种激光与PU涂层的作用机理,揭示了343 nm飞秒激光合成革微钻孔过程仅表现为光化学烧蚀,光化学和光热烧蚀同时发生于1030 nm飞秒激光钻孔过程,而1064 nm纳秒激光只显示了光热烧蚀。激光合成革表面钻孔后,测量其透湿性和抗张力。结果显示: 微孔密度越大,皮革透湿性(WVP)越大而抗张力越低,脉冲重叠的增加会导致WVP的增加和抗张力的下降;同时,随着脉冲重叠从91.7%降到50%,微孔直径从45 μm降低到30 μm,而微孔锥度从0.7°增加到12.1°;当脉冲重叠率为91.7%,微孔密度为2550/cm2时,最大的WVP增长率为306%。     

Working Pressure Dependence of Properties of Al2O3 Thin Films Prepared by Electron Beam Evaporation

The effects of working pressure on properties of Al2O3 thin films are investigated. Transmittance of the Al2O3 thin film is measured by a Lambda 900 spectrometer. Laser-induced damage threshold （LIDT） is measured by a Nd：YAG laser at 355 nm with a pulse width of 7ns. Microdefects were observed under a Nomarski microscope. The samples are characterized by optical properties and defect, as well as LIDT under the 355 nm Nd：YAG laser radiation. It is found that the working pressure has fundamental effect on the LIDT. It is the absorption rather than the microdefect that plays an important role on the LIDT of Al2O3 thin film.     

激光烧蚀制备分布反馈式有机激光器件

采用激光烧蚀的方法结合激光全息技术,直接在高分子聚合物MEH-PPV薄膜表面烧蚀光栅结构,制备了分布反馈式有机激光器。这一方法具有工艺简单、光栅参数的可控性和重复性好等优点。器件MEH-PPV的膜厚是400 nm。利用波长为355 nm的Nd-YAG纳秒激光器进行单脉冲烧蚀,获得的光栅周期和光栅高度分别为370 nm和 100 nm。利用飞秒激光放大器作为泵浦源激射DFB激光器件,得到激射阈值约为182 μJ·cm^-2·pulse^-1,光谱的波峰约在609 nm处,半高宽为4.2 nm。通过改变两光束的夹角获得了周期为360, 370, 380, 390 nm的光栅,它们对应的激光波峰分别为602.91, 609.24, 613.26, 619.01 nm。