Photoluminescence properties of thin nitrogen- and phosphorus-doped ZnO films fabricated using pulsed laser deposition

The production of n- and p-type high-quality film structures is a foreground task in tackling the problem of growing the light-emitting p-n junctions based on zinc oxide. The ZnO:N and ZnO:P thin-film samples are produced from ceramic targets using the pulsed laser deposition. Zn₃N₂, MgO, and Zn₃P₂ are introduced in the ZnO ceramic targets for the fabrication of the p-type ZnO films. Gases O₂ and N₂O are used as buffer gases. The thermal annealing of the ZnO films is employed. The resistance and photoluminescence (PL) spectra of the ZnO films are measured prior to and after annealing. The dependence of the ZnO PL peak amplitude and position prior to and after annealing on the level of doping with nitrogen and phosphorus is established. The PL characteristics of the films are studied at cw optical excitation using a He-Cd laser with a radiation wavelength of 325 nm. The PL spectra in the interval 300–700 nm are recorded by an HR4000 Ocean Optics spectrometer in the temperature range 10–400 K. The effect of the conditions for the film deposition on the PL spectra is analyzed. The effect of the N- and P-doping level of the ZnO films on the PL intensity of the films and the position of the PL bands in the UV region is investigated. The short-wavelength (250–400 nm) transmission spectra of the ZnO:P films are measured. The effect of the P-doping level on the band gap of the ZnO films is studied.     

退火温度对ZnO薄膜结构和发光特性的影响

采用反应射频磁控溅射法在 Si(100)基片上制备了高c轴择优取向的ZnO薄膜，研究了退火温度对ZnO薄膜的晶粒尺度、应力状态、成分和发光光谱的影响，探讨了ZnO薄膜的紫外发光光谱和可见发光光谱与薄膜的微观状态之间的关系.研究结果显示,在600—1000℃退火温度范围内，退火对薄膜的织构取向的影响较小，但薄膜的应力状态和成分有比较明显的变化.室温下光致发光光谱分析发现，薄膜的近紫外光谱特征与薄膜的晶粒尺度和缺陷状态之间存在着明显的对应关系；而近紫外光谱随退火温度升高所呈现的整体峰位红移是各激子峰相对比例变 关键词： ZnO薄膜 退火 光致发光 射频反应磁控溅射 可见光发射     

Influence of Al-doping on the structure and optical properties of ZnO films

Al-doped ZnO (ZnO:Al) thin films with c-axis preferred orientation were deposited on glass substrates using the radio frequency reactive magnetron sputtering technique. The effect of Al concentrations on the microstructure and the luminescence properties of the ZnO:Al thin films were studied by atomic force microscopy (AFM), X-ray diffraction (XRD), and fluorescence spectrophotometer. The results showed that the crystallization of the films was promoted by appropriate Al concentrations; the photoluminescence spectra (PL) of the samples were measured at room temperature. Strong blue peak located at 437 nm (2.84 eV) and two weak green peaks located at about 492 nm (2.53 eV) and 524 nm (2.37 eV) were observed from the PL spectra of the four samples. The origin of these emissions was discussed. In addition, absorption and transmittance properties of the samples were researched by UV spectrophotometer; the UV absorption edge shifted to a shorter wavelength first as Al was incorporated, and then to a longer wavelength with the increasing Al concentrations. The optical band gaps calculated based on the quantum confinement model are in good agreement with the experimental values.     

Modified thermal evaporation process using GeO2 for growing ZnO structures

In the current work, zinc oxide (ZnO) nano/microstructures are synthesized using a modified thermal-evaporation process by introducing germanium oxide (GeO₂) powder mixed with metallic Zn powder as the raw material. Without the use of any catalyst and oxygen flow in the furnace system, GeO₂ is utilized to provide an oxygen source for the growth of ZnO structure. The samples are treated by different temperatures ranging from 500 to 900 °C. Morphology, phase structure, and photoluminescence properties are investigated by scanning electron microscopy (SEM), X-ray diffractometer (XRD) and photoluminescence (PL) spectrometer. The structures and morphologies of the samples were found to vary with growth temperature. The XRD diffraction peaks show that the films grown at temperature from 600 to 800 °C consist of hexagonal wurtzite ZnO structures. Room-temperature PL measurement revealed ZnO spectra representing two bands: near-band-edge emission in the ultraviolet (UV) region and broad deep-level emission centered at about 500 nm. The strong UV emission in the PL spectra indicates that the GeO₂ supplies sufficient oxygen for formation of ZnO structures with few oxygen vacancies. The growth mechanism and the roles of GeO₂ for formation of ZnO structures are discussed in detail.     

Effect of irradiating ion fluence on optical properties of ZnO1−x:Nx thin films

Swift heavy ion (SHI) irradiation is an effective technique to modify the optical properties of the materials. In the present investigation, the effect of 100?MeV?Ag⁷⁺ SHI irradiation fluence on the optical properties of ZnO_1?x:N_x thin films was studied. The post irradiation spectroscopic characterizations such as UV–VIS reflectance spectroscopy, Raman spectroscopy and photoluminescence (PL) spectroscopy analysis were carried out. The studies imply that when the SHI passes through the solid, the higher electronic stopping power of ions can weaken oxygen bonds in ZnO, resulting in the formation of donor defects such as oxygen vacancies and zinc interstitials. The formation of donor defects has been acknowledged through the increase in bandgap with irradiating ion fluence. The blue shift observed from the Raman spectra for the 3?×?10¹³ ions/cm² fluence-irradiated films implies the existence of compressive stress in the films. The PL analysis acknowledges the formation of donor defects upon irradiation. Furthermore, it conveys that the presence of N atoms in ZnO lattice leads to the formation of a less number of defects as compared with undoped ZnO while irradiation.     

氧氩比对纳米ZnO薄膜蓝光发射光谱的影响

利用射频磁控溅射方法,在石英表面上制备了具有良好的c轴取向的纳米ZnO薄膜。室温下,在300 nm激发下,在450 nm附近观测到ZnO薄膜的蓝光发射谱(430~460 nm)。分析了气氛中氧气与氩气比对薄膜质量及蓝光发射光谱的影响,给出了纳米ZnO薄膜光致发光谱(PL)的积分强度和峰值强度与氧氩比关系。探讨了纳米ZnO薄膜的蓝光光谱的发射机制,初步证实了ZnO蓝光发射(2.88~2.69 eV)来自氧空位(VO)形成的浅施主能级上的电子至价带顶的跃迁。     

Room temperature growth and properties of ZnO films by pulsed laser deposition

ZnO thin films were prepared by pulsed laser deposition at room temperature on glass substrates with oxygen pressures of 10-30 Pa. The structural, electrical, and optical properties of ZnO films were studied in detail. ZnO films had an acceptable crystal quality with high c-axis orientation and smooth surface. The resistivity was in the 10² Ω cm order for ZnO films, with the electron concentration of 10¹⁶-10¹⁷ cm⁻³. All the films showed a high visible transmittance ∼90% and a high UV absorption about 90-100%. The UV emission ∼390 nm was observed in the photoluminescence spectra. The oxygen pressures in the 10-30 Pa range were suitable for room temperature growth of high-quality ZnO films.     

Ag掺杂p型ZnO薄膜及其光电性能研究

采用超声喷雾热分解法在石英衬底上以醋酸锌水溶液为前驱体,以硝酸银水溶液为Ag掺杂源生长了Ag掺杂ZnO(ZnO：Ag)薄膜.研究了衬底温度对所得ZnO：Ag薄膜的晶体结构、电学和光学性质的影响规律.所得ZnO：Ag薄膜结构良好,在室温光致发光谱中检测到很强的近带边紫外发光峰,透射光谱中观测到非常陡峭的紫外吸收截止边和较高的可见光区透过率,表明薄膜具有较高的晶体质量与较好的光学特性.霍尔效应测试表明,在500℃下获得了p型导电的ZnO：Ag薄膜,载流子浓度为5.30×10¹⁵cm关键词： ZnO：Ag薄膜 p型掺杂 超声喷雾热分解 霍尔效应     

退火对ZnO薄膜光学特性的影响

用射频磁控溅射法在蓝宝石衬底上制备出ZnO薄膜,通过X射线衍射(XRD)、扫描电镜(SEM)和光致发光(PL)谱等研究了退火温度对ZnO薄膜结构和光学性质的影响。测量结果显示,所制备的ZnO薄膜为六角纤锌矿结构,具有沿c轴的择优取向;随着退火温度的升高,(002)XRD峰强度和平均晶粒尺寸增大,(002)XRD峰半高宽(FWHM)减小,光致发光紫外峰强度增强。结果证明,用射频磁控溅射法通过适当控制退火温度可得到高质量ZnO薄膜。     

ZnO薄膜的制备和发光特性的研究

用射频磁控溅射的方法在石英衬底上沉积了氧化锌薄膜，在室温下测量了样品的XRD曲线、吸收光谱以及光致发光光谱。探讨了气氛中氧气与氩气比对制备薄膜的影响，从XRD谱中可以看出，样品具有较好的结晶状态。另外，样品在紫外有较强的吸收，而其光致发光也是较强的紫外发射，这表明带间跃迁占了主导地位，以上结果说明：用溅射方法制备的ZnO薄膜结晶质量较好，富锌状态有所改善。     

Luminescent properties of ZnO thin films treated by pulse-modulated high-power inductively coupled plasma

The effect of hydrogen plasma irradiation on luminescence properties of ZnO thin films was studied by using a pulse-modulated inductively coupled plasma technique. H-plasma exposure distance was changed to investigate the effect of hydrogen plasma irradiation on luminescent properties. Room temperature cathodoluminescence (CL) spectrum shows that hydrogen plasma irradiation can increase the efficiency of UV emission at 3.27 eV, and the improvement is strongly dependent on H-plasma exposure distance. For low temperature CL spectra, the intensity of donor-acceptor pair (DAP) transition at 3.315 eV has been increased more rapidly after hydrogen plasma irradiation, leading DAP to be the dominant transition.     

Photoluminescence from ZnO-SiO2 opals with different sphere diameters and thicknesses

We systematically investigated the photoluminescence (PL) and transmittance characteristics of ZnO-SiO₂ opals with varied positions of the stop-band and film thicknesses. An improved ultraviolet (UV) luminescence was observed from ZnO-SiO₂ composites over pure ZnO nanocrystals under 325 nm He-Cd laser excitation at room temperature. The UV PL of ZnO nanocrystals in SiO₂ opals with stop-bands center of 410 nm is sensitive to the thickness of opal films, and the UV PL intensity increases with the film thickness increasing. The PL spectra of ZnO nanocrystals in SiO₂ opals with stop-bands center of 570 nm show a suppression of the weak visible band. The experimental results are discussed based on the scattering and/or absorbance in opal crystals.     

原子层沉积制备氧化锌纳米薄膜的光学性质研究

采用原子层沉积技术(ALD),以二乙基锌和水为前驱体,在衬底温度分别为110和190 ℃的条件下制备了致密的氧化锌纳米薄膜。采用X射线光电子能谱,荧光光谱和椭偏仪等表征手段对薄膜的成分和光学性质进行了研究。结果表明,随着沉积温度的增加,氧化锌薄膜内—OH含量降低,说明氧化锌薄膜生长过程中的化学反应更加完全;另外,沉积温度增加后,薄膜在365 nm处的激子发射峰出现了明显的增强,同时可见光区的荧光发射峰消失,表明薄膜内的缺陷态减少。随着成膜质量的提高,氧化锌薄膜的电子迁移率从25提高至32 cm2·(V·S)-1。椭偏测量的拟合结果表明,在375～800 nm的波长范围内,氧化锌薄膜的折射率逐渐从2.33降至1.9,呈现出明显的色散现象;另外,不同温度下制备的氧化锌薄膜光学带隙均为3.27 eV左右,这说明沉积温度对薄膜的带隙没有明显影响。     

氧压对飞秒激光沉积ZnO/Si(100)薄膜光学性能的影响

利用飞秒脉冲激光沉积法在n-Si（100）单晶衬底上制备了ZnO薄膜, 分析了衬底温度、激光能量、氧压及退火处理对薄膜结构和光学性能的影响. X射线衍射结果表明, 当激光能量为15?mJ、氧压为10?mPa时, 80?℃生长的薄膜取向性最好. 场扫描电子显微镜结果显示薄膜的晶粒尺寸随激光能量的增加而减小、随衬底温度的升高而增大且退火后明显变大. 紫外-可见透射光谱显示薄膜具有90%以上的可见光透过率.光致发光谱表明当氧压为10 mPa时,除了ZnO的紫外本征峰外, 还有一波长为410 nm的强紫光峰, 当氧压增至20 mPa以上, 所有缺陷峰均消失, 只有376 nm处的紫外本征峰. 与纳秒激光法所制备的薄膜特性进行了比较, 结果表明, 虽然纳秒激光沉积所制备的薄膜具有更高的c轴取向度, 但飞秒激光沉积制备的薄膜具有更好的发光性能. 关键词： 氧化锌 飞秒脉冲激光沉积 透过率 光致发光     

Structural and optical properties of nanocrystalline ZnO thin films synthesized by the citrate precursor route

Nanocrystalline zinc oxide (ZnO) thin films have been deposited by spin-coating polymeric precursors synthesized by the citrate precursor route using ethylene glycol and citric acid as chelating agents. The ZnO thin films were annealed in air at different temperatures for 10 min. The films were characterized by different structural and optical techniques, including X-ray diffraction (XRD), atomic force microscopy (AFM), optical transmission spectroscopy, and photoluminescence (PL). The thermal decomposition of polymeric precursor was studied by thermogravimetric analysis (TGA). XRD analysis with grazing incidence and rocking curves indicate that the ZnO films are polycrystalline with preferential orientation along the c-axis direction with a full-width at half-maximum (FWHM) of 0.31° for 600 °C-annealed samples. On annealing, the texturing in films increased along with a decrease in FWHM. AFM micrographs illustrate that the ZnO films are crack-free with well-dispersed homogeneous and uniformly distributed spherical morphology. The synthesized ZnO thin films have transparency >85% in the visible region exhibiting band edge at 375 nm, which becomes sharper with anneal. Room temperature PL spectra of these films show strong ultraviolet (UV) emission around 392 nm with an increase in intensity with annealing temperature, attributed to grain growth. Deconvolution of the PL spectra reveals that there is coupling of free excitons with higher orders of longitudinal optical (LO) phonon replicas leading to a broad asymmetric near-band-edge peak.     

Optical properties of ZnO and ZnO:Ce layers grown by spray pyrolysis

In this paper, zinc oxide (ZnO) and cerium-doped zinc oxide (ZnO:Ce) films were deposited by reactive chemical pulverization spray pyrolysis technique using zinc and cerium chlorides as precursors. The effects of Ce concentration on the structural and optical properties of ZnO thin films were investigated in detail. These films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and photoluminescence (PL) measurements. All deposited ZnO layers at the temperature 450 °C are polycrystalline and indicate highly c-axis oriented structure. The dimension of crystallites depends on incorporation of Ce atoms into the ZnO films. The photoluminescence spectra of the films have been studied as a function of the deposition parameters such as doping concentrations and post grows annealing. Photoluminescence spectra were measured at the temperature range from 13 K to 320 K.     

磁控溅射制备ZnO薄膜的结构及发光特性研究

采用射频反应磁控溅射法在玻璃衬底上制备出具有c轴高择优取向的ZnO薄膜,利用X射线衍射、扫描探针显微镜及荧光分光光度法研究了生长温度对ZnO薄膜微观结构及光致发光特性的影响。结果表明,合适的衬底温度有利于提高ZnO薄膜的结晶质量;在室温下测量样品的光致发光谱(PL),观察到波长位于400 nm左右的紫光、446 nm左右的蓝色发光峰及502 nm左右微弱的绿光峰,随衬底温度升高,样品的PL谱中紫光及蓝光强度逐渐增大,同时,绿光峰的强度也表现出一定程度的增强。经分析得出紫光应是激子发光所致,而锌填隙则是引起蓝光发射的主要原因,502 nm左右的绿光峰应该是氧的深能级缺陷造成的。此外,还测量了样品的吸收谱,并结合样品吸收谱的拟合结果对光致发光机理的分析作了进一步的验证。     

Microstructures and optical properties of Cu-doped ZnO films prepared by radio frequency reactive magnetron sputtering

Pure and Cu-doped ZnO (ZnO:Cu) thin films were deposited on glass substrates using radio frequency (RF) reactive magnetron sputtering. The effect of substrate temperature on the crystallization behavior and optical properties of the ZnO:Cu films have been studied. The crystal structures, surface morphology and optical properties of the films were systematically investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and a fluorescence spectrophotometer, respectively. The results indicated that ZnO films showed a stronger preferred orientation toward the c-axis and a more uniform grain size after Cu-doping. As for ZnO:Cu films, the full width at half maxima (FWHM) of (0 0 2) diffraction peaks decreased first and then increased, reaching a minimum of about 0.42° at 350 °C and the compressive stress of ZnO:Cu decreased gradually with the increase of substrate temperature. The photoluminescence (PL) spectra measured at room temperature revealed two blue and two green emissions. Intense blue-green luminescence was obtained from the sample deposited at higher substrate temperature. Finally, we discussed the influence of annealing temperature on the structural and optical properties of ZnO:Cu films. The quality of ZnO:Cu film was markedly improved and the intensity of blue peak (∼485 nm) and green peak (∼527 nm) increased noticeably after annealing. The origin of these emissions was discussed.     

Enormous enhancement of ZnO nanorod photoluminescence

ZnO nanorod arrays were grown on quartz slices in the aqueous solution of zinc acetate and hexamethylenetetramine at 90 °C. Then ZnO:Mg shells were epitaxially grown on the nanorods to form core/shell structures in the aqueous solution of zinc acetate, magnesium acetate and hexamethylenetetramine at the same temperature. Effects of the shells and UV laser beam irradiation on the crystal structure and photoluminescence properties of ZnO nanorods were studied. ZnO:Mg shells suppress the green emission and enhance the UV emission intensity of the nanorods by 38 times. Enhancement of the UV emission depends on the Mg content in the shells. Short time UV laser beam irradiation could improve ZnO nanorod emission efficiently. The UV emission intensity of ZnO nanorods is enhanced by 71 times by capping and subsequent UV laser beam irradiation.     

Nanostructure and optical properties of M doped ZnO (M=Ni, Mn) thin films prepared by sol-gel process

The transparent thin films of undoped, Mn-doped, and Ni-doped zinc oxide (ZnO) have been deposited on glass substrates via sol-gel technique using zinc acetate dehydrate, nickel chloride, and manganese chloride as precursors. The structural properties and morphologies of the deposited undoped and doped ZnO thin films have been investigated. X-ray diffraction (XRD) spectra, scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to examine the morphology and microstructure of the thin films. Optical properties of the thin films were determined by photoluminescence (PL) and UV/vis spectroscopy. The analyzed results indicate that the obtained films are of good crystal quality and have smooth surfaces, which have a pure hexagonal wurtzite ZnO structure without any Mn or Ni related phases. The band gap energy was estimated by Tauc's method and found to be 3.28, 3.26, and 3.34 eV for ZnO, Ni-doped ZnO, and Mn-doped ZnO thin films at room temperature, respectively. Room temperature photoluminescence is observed for the ZnO, Ni-doped ZnO, and Mn-doped ZnO thin films.