退火温度对低温生长MgxZn1-xO薄膜光学性质的影响

用射频磁控溅射法在80℃衬底温度下制备出MgxZn1-xO(x=0.16)薄膜,用X射线衍射(XRD)、光致发光(PL)和透射谱研究了退火温度对MgxZn1-xO薄膜结构和光学性质的影响.测量结果显示,MgxZn1-xO薄膜为单相六角纤锌矿结构,并且具有沿c轴的择优取向;随着退火温度的升高,(002)XRD峰强度、平均晶粒尺寸和紫外PL峰强度增大,(002)XRD峰半高宽(FWHM)减小.结果证明,用射频磁控溅射法通过适当控制退火温度可得到高质量MgxZn1-xO薄膜.     

溅射气氛对RF反应磁控溅射制备ZnO薄膜微结构及光致发光特性的影响

用射频反应磁控溅射法在不同溅射压强和氩氧比下制备了ZnO薄膜,通过X射线衍射(XRD)、扫描电镜(SEM)和光致发光(PL)谱等研究了溅射压强和氩氧比对ZnO薄膜结构和光学性质的影响。测量结果显示,所制备的ZnO薄膜为六角纤锌矿结构,具有沿c轴的择优取向;溅射压强P=0.6Pa,氩氧比Ar/O2=20/5.5sccm时,(002)晶面衍射峰强度和平均晶粒尺寸较大,(O02)XRD峰半峰全宽(FWHM)最小,光致发光紫外峰强度最强。     

退火温度对低温生长MgxZn1－xO薄膜光学性质的影响

用射频磁控溅射法在80℃衬底温度下制备出Mg_xZn_1-xO(x=0.16)薄膜，用X射线衍射(XRD)、光致发光(PL)和透射谱研究了退火温度对Mg_xZn_1-xO薄膜结构和光学性质的影响.测量结果显示，Mg_xZn_1-xO薄膜为单相六角纤锌矿结构，并且具有沿c轴的择优取向；随着退火温度的升高，(002)XRD峰强度、平均晶粒尺寸和紫外PL峰强度增大，(002)XRD峰半高宽(F 关键词： xZn_1-xO薄膜')" href="#">Mg_xZn_1-xO薄膜 射频磁控溅射 退火     

射频磁控溅射法制备ZnO薄膜的绿光发射

用射频磁控溅射法,在硅衬底上制备出具有良好的(002)择优取向的多晶ZnO薄膜。研究了室温下薄膜的光致发光特性,观察到显著的单绿光发射(波长为514nm)峰。在氧气中830℃高温退火后,薄膜结晶质量明显提高,绿光发射峰强度变弱;在真空中830℃高温退火后,绿光发射峰强度增加。绿光发射源于氧空位深施主能级到价带顶的电子跃近。     

ZnO薄膜的制备和结构特性及应变

在SiO₂/Si衬底上面,利用射频磁控溅射方法,在不同的工艺条件下生长ZnO薄膜,然后进行热处理(600～1000℃退火).研究了氩氧比和退火温度对薄膜结晶性能的影响.薄膜的表面结构和晶体特性通过扫描电子显微镜(SEM)、X射线衍射(XRD)来进行表征.结果表明:所制备的薄膜为多晶纤锌矿结构,具有垂直于衬底的c轴(002)方向的择优取向性.热处理可使ZnO(002)衍射峰相对强度增强,半峰全宽(FWHM)变小,即退火使c轴生长的薄膜取向性增强.未经退火的ZnO薄膜存在张应力,经过热处理后应力发生改变,最后变成压应力,并且随着退火温度的升高,压应力逐渐增大.     

退火对多晶ZnO薄膜结构与发光特性的影响

用射频反应溅射法在Si（111）衬底上制备了C轴取向的多晶ZnO薄膜，通过不同温度的退火处理，研究了退火对多晶ZnO薄膜结构和发光特性的影响.由x射线衍射得知，随退火温度的升高，晶粒逐渐变大，薄膜中压应力由大变小至出现张应力.光致发光测量发现，样品在430nm附近有一光致发光峰, 峰的强度随退火温度升高而减弱，联合样品电阻率随退火温度升高而逐渐变大的测量及能级图，推测出ZnO薄膜中的蓝光发射主要来源于锌填隙原子缺陷能级与价带顶能级间的跃迁. 关键词： ZnO薄膜 退火 光致发光 射频反应溅射     

溶胶-凝胶法制备MgxZn1-xO薄膜的结构及光学特性

用溶胶-凝胶法制备了一系列的Mg_xZn_1-xO(0≤x≤0.3)薄膜,并用X射线衍射(XRD)和光致发光(PL)研究了不同的退火温度和Mg的掺杂含量对Mg_xZn_1-xO薄膜的结构和光学性质的影响.研究表明:Mg_xZn_1-xO薄膜为单相六角纤锌矿结构,并且具有沿c轴的择优取向;发现了中间热处理温度为350℃的Mg_xZn_1-xO薄膜退火温度的转折点为700℃,低于这个温度时随退火温度的升高,(002)衍射峰强度增强且掺Mg的薄膜既有紫外光又有绿光发射;800℃退火时,薄膜的(002)衍射峰强度减小,出现了(100)和(101)衍射峰,且掺Mg的薄膜只有紫外发光峰.不同的掺杂浓度对于发光也有影响,低于700℃退火时,ZnO薄膜只出现紫外发光峰,掺Mg的薄膜却出现了紫外和绿光两个发光峰.     

退火温度对ZnO薄膜结构和发光特性的影响

采用反应射频磁控溅射法在 Si(100)基片上制备了高c轴择优取向的ZnO薄膜，研究了退火温度对ZnO薄膜的晶粒尺度、应力状态、成分和发光光谱的影响，探讨了ZnO薄膜的紫外发光光谱和可见发光光谱与薄膜的微观状态之间的关系.研究结果显示,在600—1000℃退火温度范围内，退火对薄膜的织构取向的影响较小，但薄膜的应力状态和成分有比较明显的变化.室温下光致发光光谱分析发现，薄膜的近紫外光谱特征与薄膜的晶粒尺度和缺陷状态之间存在着明显的对应关系；而近紫外光谱随退火温度升高所呈现的整体峰位红移是各激子峰相对比例变 关键词： ZnO薄膜 退火 光致发光 射频反应磁控溅射 可见光发射     

退火对ZnO:Al薄膜光致发光性能的影响

 采用溶胶-凝胶工艺在石英衬底上制备ZnO:Al（AZO）薄膜，通过不同温度的退火处理，研究了退火对AZO薄膜结构和光致发光特性的影响。XRD图谱表明：所制备的薄膜具有c轴高度择优取向，随着退火温度的升高，(002)峰的强度逐渐增强，同时(002)峰的半高宽逐渐减小,表明晶粒在不断增大。未退火样品的光致发光（PL）谱由361 nm附近的紫外带边发射峰和500 nm附近的深能级发射峰组成。样品经退火后，以500 nm为中心的绿带发射逐渐减弱，而带边发射强度有所增强,并且逐渐红移到366 nm附近，与吸收边移动的测试结果相吻合。对经过不同时间退火的样品分析表明，AZO薄膜的发光特性与退火时间也有很大关系，时间过短可见波段的发射较强，但时间过长会使晶粒发生团聚，导致紫外发射峰强度减弱。     

高浓度Er/Yb共掺ZnO薄膜的结构及室温光致发光特性

采用射频磁控溅射方法制备了Er/Yb共掺ZnO薄膜,研究了退火处理对高浓度Er/Yb共掺ZnO薄膜的结构演化和光致发光(PL)特性的影响。X射线衍射分析结果表明:Er/Yb掺杂导致ZnO薄膜的晶粒细化及择优取向性消失,ZnO晶粒随退火温度的增加而逐渐长大。900℃退火时,出现Er3 、Yb3 偏析,退火温度高于1000℃时,薄膜与基体间发生了界面反应,1200℃时,ZnO完全转变为Zn2SiO4相。光致发光测量结果表明:高于900℃退火处理后,Er/Yb共掺ZnO薄膜在1540 nm附近具有明显的光致发光,发光强度在退火温度为1050℃时达到最大值;光致发光光谱呈现典型的晶体基质中Er3 离子发光光谱所具有的明锐多峰结构特征。此外,探讨了薄膜结构演化及其对光致发光光谱的影响。     

退火对ZnO薄膜的结构和光学性质的影响

采用射频磁控溅射法在Si衬底上制备了高c轴择优取向的ZnO薄膜,研究了退火对ZnO薄膜的晶粒尺度和发光光谱的影响。XRD结果显示退火可以改善ZnO薄膜的结构特性,PL谱结果显示退火对ZnO薄膜的发光强度产生很大影响。     

Annealing effects of sapphire substrate on properties of ZnO films grown by magnetron sputtering

The annealing effects of sapphire substrates on the quality of epitaxial ZnO films grown by dc reactive magnetron sputtering were studied. The atomic steps formed on (0001) sapphire (α-Al₂O₃) substrates surface by annealing at high temperature were analyzed by atomic force microscopy. Their influence on the growth of ZnO films was examined by X-ray diffraction and photoluminescence measurements. Experimental results indicate that the film quality is strongly affected by annealing treatment of the sapphire substrate surface. The optimum annealing temperature of sapphire substrates for ZnO grown by magnetron sputtering is 1400 °C for 1 h in air. PACS 81.40.Ef; 68.55.Jk; 81.05.Dz; 81.15.Cd     

射频磁控溅射法制备的Eu掺杂ZnO薄膜的结构及其发光性质

用射频磁控溅射法在石英衬底上制备了ZnO:Eu3+薄膜,通过X射线衍射仪、扫描电子显微镜和荧光光谱仪测试了薄膜结构、形貌以及发光性能,重点考察了溅射功率和退火工艺对其组织结构和发光性能的影响.结果表明:样品均呈现ZnO的六角纤锌矿结构,增大溅射功率有利于形成ZnO的c轴择优取向;增大溅射功率以及高温退火会使晶粒尺寸增大...     

Microstructure and optical properties of ZnO/porous silicon nanocomposite films

In this study, porous silicon (PS) templates were formed by electrochemical anodization on p-type (100) silicon wafer and ZnO films were deposited on PS substrates using radio frequency (RF) reactive magnetron sputtering technique. The effects of oxygen partial pressures of growth ZnO films and annealing ambience on the microstructure and photoluminescence (PL) of the ZnO/PS nanocomposite films were systematically investigated by X-ray diffraction and fluorescence spectrophotometry. The results indicated that all ZnO/PS nanocomposite films were polycrystalline in nature with a hexagonal wurtzite structure and the (002) oriented ZnO films had the best crystal quality under O₂:Ar ratio of 10:10 sccm and annealing in vacuum. PL measurements at room temperature revealed that ZnO/PS nanocomposite systems formed a broad PL band including the blue and green emissions from ZnO and red-orange emission from the PS. The mechanism and interpretation of broadband PL of the nanocomposites were discussed in detail using an oxygen-bonding model in PS and a native defects model in ZnO.     

Effects of Ti-doped concentration on the microstructures and optical properties of ZnO thin films

The Ti-doped ZnO (ZnO:Ti) thin films have been deposited on glass substrates by radio frequency (RF) reactive magnetron sputtering technique with different Ti doping concentrations. The effect of Ti contents on the crystalline structure and optical properties of the as-deposited ZnO:Ti films was systematically investigated by X-ray diffraction (XRD), scanning electronic microscopy (SEM) and fluorescence spectrophotometer. The XRD measurements revealed that all the films had hexagonal wurtzite type structure with a strong (100) preferential orientation and relatively weak (002), (101), and (110) peaks. It was found that the intensity of the (100) diffraction peaks was strongly dependent on the Ti doping concentration. And the full width at half-maximum (FWHM) of (002) diffraction peaks constantly changed at various Ti contents, which decreased first and then increased, reaching a minimum of about 0.378° at 1.43 at.% Ti. The morphologies of ZnO:Ti films with 1.43 at.% Ti showed a denser texture and better smooth surface. All the films were found to be highly transparent in the visible wavelength region with an average transmittance over 90%. Compared with E_g = 3.219 eV for pure ZnO film, all the doping samples exhibited a blue-shift of E_g. It can be attributed to the incorporation of Ti atoms and raising the concentration of carriers. Five emission peaks located at 412, 448, 486, 520, and 550 nm were observed from the photoluminescence spectra measured at room temperature and the origin of these emissions was discussed.     

Optical properties of ZnO thin films on SiO2 substrates deposited by radio frequency magnetron sputtering

The optical properties of both the annealed and as-deposited ZnO thin films by radio frequency (RF)magnetron sputtering on SiO2 substrates were studied. In the annealed films, two pronounced well defined exciton absorption peaks for the A and B excitons were obtained in the absorption spectra, a strong free exciton emission without deep-level emissions was observed in the photoluminescence (PL) spectra at room temperature. It was found that annealing the films in oxygen dramatically improved the optical properties and the quality of the films.     

氧氩比对纳米ZnO薄膜蓝光发射光谱的影响

利用射频磁控溅射方法,在石英表面上制备了具有良好的c轴取向的纳米ZnO薄膜。室温下,在300 nm激发下,在450 nm附近观测到ZnO薄膜的蓝光发射谱(430~460 nm)。分析了气氛中氧气与氩气比对薄膜质量及蓝光发射光谱的影响,给出了纳米ZnO薄膜光致发光谱(PL)的积分强度和峰值强度与氧氩比关系。探讨了纳米ZnO薄膜的蓝光光谱的发射机制,初步证实了ZnO蓝光发射(2.88~2.69 eV)来自氧空位(VO)形成的浅施主能级上的电子至价带顶的跃迁。     

Microstructures and optical properties of Cu-doped ZnO films prepared by radio frequency reactive magnetron sputtering

Pure and Cu-doped ZnO (ZnO:Cu) thin films were deposited on glass substrates using radio frequency (RF) reactive magnetron sputtering. The effect of substrate temperature on the crystallization behavior and optical properties of the ZnO:Cu films have been studied. The crystal structures, surface morphology and optical properties of the films were systematically investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and a fluorescence spectrophotometer, respectively. The results indicated that ZnO films showed a stronger preferred orientation toward the c-axis and a more uniform grain size after Cu-doping. As for ZnO:Cu films, the full width at half maxima (FWHM) of (0 0 2) diffraction peaks decreased first and then increased, reaching a minimum of about 0.42° at 350 °C and the compressive stress of ZnO:Cu decreased gradually with the increase of substrate temperature. The photoluminescence (PL) spectra measured at room temperature revealed two blue and two green emissions. Intense blue-green luminescence was obtained from the sample deposited at higher substrate temperature. Finally, we discussed the influence of annealing temperature on the structural and optical properties of ZnO:Cu films. The quality of ZnO:Cu film was markedly improved and the intensity of blue peak (∼485 nm) and green peak (∼527 nm) increased noticeably after annealing. The origin of these emissions was discussed.