激光熔覆硬质合金强化化纤切断刀的研究

在机械压制法预置硬质合金WC/Co粉末的条形55Si2Mn弹簧钢上,用激光熔覆方法制备了化纤切断刀.调整熔覆层粉末配方中Al、TiC的加入量,结果表明加适量的Al粉能有效地抑制气孔,加TiC粉末能提高熔覆硬度.通过优化激光熔覆工艺参数,得到了无气孔缺陷、组织性能良好、硬度达到HV0.21250的激光熔覆层,达到了化纤切断刀的性能要求.     

多棒串接固体激光器谐振腔的研究

运用矩阵光学的方法对多棒串接固体激光器的谐振腔参数及其在平平腔时的热稳条件进行了研究，并计算了六棒串接平平腔固体激光器的稳定区.结果证明：多棒串接固体激光器的稳定区和非稳区相互间隔，在平平腔总腔长、激光棒数量n和棒间距L一定的条件下，当采用对称结构时(L₁=L₂)，则谐振腔的每段稳定区均达到最大；且只要 平平腔满足L₁=L₂=L/2以及热焦距f在大于某个下限值f_m时，稳定性条件01< 关键词： 多棒串接固体激光器 稳定区 热稳条件     

飞秒激光烧蚀LiNbO3晶体的形貌特征与机理研究

采用了不同能量的单脉冲和多脉冲飞秒激光对LiNbO₃晶体进行烧蚀，并刻蚀了表面衍射型光栅.通过扫描电镜和原子力显微镜观察了烧蚀点的形貌特征，首次发现利用单束飞秒激光脉冲对LiNbO₃晶体烧蚀，可以得到超衍射极限的烧蚀点，当聚焦光斑直径约为2μm、能量为170nJ的单脉冲飞秒激光作用时，烧蚀点的直径约为400nm，100nJ，17个脉冲作用时烧蚀点的直径约为800nm.同时可以观察到在能量较低的多脉冲飞秒激光作用下， LiNbO₃晶体呈现出大约200nm周期性分布的波纹状结构.实验结果表明，选择合适参数的飞秒激光脉冲可以对LiNbO₃晶体进行超衍射极限加工，这对于利用飞秒激光制作LiNbO₃基质的微纳光电子器件有十分重要的意义.     

连续CO2激光辐照加热不锈钢时的反常温度涨落特性

研究了在连续CO₂激光辐照下不锈钢表面的温度涨落特性.实验中用国产HWRX-Ⅲ型红外快速热像仪测量了不锈钢表面的升温过程及温度涨落.发现不锈钢在激光辐照下随辐照时间的增加和温度的升高,其温度涨落的幅度基本保持不变.这与理论预言不符,也不同于已研究过的铝、低碳钢、环氧树脂和有机玻璃等材料.随辐照时间的增加,温度的升高,其温度涨落的幅度基本保持不变.这一特性是由不锈钢的热学参数如热传导率、热扩散率随温度变化的规律所决定的.详细探讨了材料热学参数随温度的变化对温度涨落的影响. 关键词：     

Wear resistance of laser cladding and plasma spray welding layer on stainless steel surface

The effect of coatings, which are formed with laser cladding and plasma spray welding on 1Cr18Ni9Ti base metal, on wear resistance is studied, A 5-kW transverse flowing CO2 laser is used for cladding Co base alloy powder pre-placed on the substrate. Comparing with the plasma spray coatings, the spoiled rate of products with laser clad layers was lower and the rate of finished products was higher. Their microstructure is extremely fine. They have close texture and small size grain. Their dilution resulting from the compositions of the base metal and thermal effect on base metal are less. The hardness, toughness,and strength of the laser cladding layers are higher. Wear tests show that the laser layers have higher properties of anti-friction, anti-scour and high-temperature sliding strike. The wear resistance of laser clad layers are about one time higher than that of plasma spray welding layer.     

耐酸不锈钢表面激光熔覆层耐腐蚀研究

本文研究了在耐酸不锈钢基体上采用激光熔覆和等离子喷焊二种工艺形成的涂层对耐腐蚀性的影响。使用５ｋＷ横流ＣＯ２激光器对预置在基体上的Ｃｏ基自熔合金粉末进行熔覆加工,得到的熔层与等离子焊层对比：激光熔层缺陷率低,被机体稀释率更小,成品率更高。其组织致密均匀,晶粒细小,熔层硬度与强韧性更高。性能试验证明：激光熔层有更好的耐腐蚀性能。     

THEORETICAL INVESTIGATION OF ELECTRON-NEUTRAL ATOM COLLISION PROCESS AND ELECTRON TRANSPORT PARAMETERS IN DC GLOW DISCHARGE OF PLASMA WITH A TRANSVERSE MAGNETIC FIELD

A Monte Carlo simulation (MCS) technique is used to simulate the cathode sheath region of a helium dc glow discharge. In such a simulation, a nonuniform electric field and a transverse uniform magnetic field are considered. When the magnetic field intensity increases from 0 to 800 G, all types of collision considered in this paper are enhanced. This result is in agreement with the experimental result. The results also show that with the increase of magnetic field intensity, the electron transport time, the electron density increase, and the electron mean energy decreases.     

Optical Characterization of β-FeSi2 Thin Films Prepared by Femtosecond Laser Ablation

Iron disilicide thin films are prepared on fused quartz using femtosecond laser deposition （FsPLD） with a FeSi2 alloy target. X-ray diffraction results indicate the films are single-phase, orthorhombic, β-FeSi2. Field scanning electron microscopy, high resolution transmission electron microscopy, UV-VIS-NIR spectroscopy and Raman microscope are used to characterize the structure, composition, and optical properties of the β-FeSi2 films. Normal incidence spectral transmittance and reflectance data indicate a minimum, direct energy gap of 0.85 eV. The two most intense lines of Raman scattering peaked at 181.3 cm^-1 and 235.6cm^-1 for the film on fused quartz, and at 191.2cm^-1 and 243.8cm^-1 for the film on Si （100）, are observed.     

The application of arbitrary incidence laser beams heat treatment temperature field calculation formulas

Based on the calculation formulas of heat treatment temperature field for an arbitrary incident laser intensity distribution, the transformation intensity distribution of CO2 laser beam passing an integrating mirror is studied theoretically and experimentally. The derived formulas are applied in laser heat treatment research which is transformed by optical system, and the theoretical calculation results are compared with experimental results. It is shown that the formulas can be used to calculate the laser heat treatment temperature field accurately, and the calculation speed is obviously faster than the numerical calculation methods with the same precision. The calculation software can be used to select proper experiment parameters.