AlGaN-Based Solar-Blind Schottky Photodetectors Fabricated on AlN/Sapphire Template

We report AlGaN-based back-illuminated solar-blind Schottky-type ultraviolet photodetectors with the cutoff- wavelength from 280nm to 292nm without bias. The devices show low dark current of 2.1× 10^-6A/cm^2 at the reverse bias of 5 V. The specific detectivity D＊ is estimated to be 3.3 × 10^12cmHz^1/2 W^-1 . To guarantee the performance of the photodetectors, the optimization of AlGaN growth and annealing condition for Schottky contacts were performed. The results show that high-temperature annealing method for Ni/Pt Schottky contacts is effective for the reduction of leakage current.     

Optical Defect in GaN-Based Laser Diodes Detected by Cathodoluminescence

GaN-based laser diodes （LDs） with 399 nm wavelength are grown on sapphire substrates by metal organic chemical vapour deposition （MOCVD）. Electroluminescence spectra of the fabricated LDs show that the LDs from some grown wafers failed to emit laser. The SEM and XRD results show the similar surface morphology and interface qualities of multi quantum wells （MQWs） and super-lattices between LDs that succeed and fail to emit laser. However, the cathodoluminescence （CL） measurements reveal a kind of optical defect rather than structural defect in un-emitted LDs. Further depth-dependent CL imaging observation indicates that such optical defects originate from the MQWs to the surface of LDs as a non-irradiative recombination centre that should cause the failure of laser emitting of LDs.     

GaMnN材料红外光谱中洛伦兹振子模型的遗传算法研究

利用红外反射光谱研究了蓝宝石衬底上用金属有机物化学气相淀积方法生长的稀磁半导体GaMnN材料的晶格振动特性. 并成功地将改进的遗传算法应用于其红外反射光谱洛伦兹振子模型参数的提取. 通过与GaN薄膜的洛伦兹振子模型参数的对比研究发现,GaN掺入Mn后,ω_TO向高频方向移动,γ,ε_∞和ε_s均增加,而ω_LO基本保持不变. 文中同时分析和讨论了Mn对晶格振动特性的影响及 关键词： 稀磁半导体GaMnN材料 遗传算法 洛伦兹振子模型 参数提取     

蓝宝石衬底上GaN/AlxGa1-xN超晶格插入层对AlxGa1-xN外延薄膜应变及缺陷密度的影响

室温300K下,由于Al_xGa_1-xN的带隙宽度可以从GaN的3.42eV到AlN的6.2eV之间变化,所以Al_xGa_1-xN是紫外光探测器和深紫外LED所必需的外延材料.高质量高铝组分Al_xGa_1-xN材料生长的一大困难就是Al_xGa_1-xN与常用的蓝宝石衬底之间大的晶格失配和热失配.因而采用MOCVD在GaN/蓝宝石上生长的Al_xGa_1-xN薄膜由于受张应力作用非常容易发生龟裂.GaN/Al_xGa_1-xN超晶格插入层技术是释放应力和减少Al_xGa_1-xN薄膜中缺陷的有效方法.研究了GaN/Al_xGa_1-xN超晶格插入层对GaN/蓝宝石上Al_xGa_1-xN外延薄膜应变状态和缺陷密度的影响.通过拉曼散射探测声子频率从而得到材料中的残余应力是一种简便常用的方法,Al_xGa_1-xN外延薄膜的应变状态可通过拉曼光谱测量得到.Al_xGa_1-xN外延薄膜的缺陷密度通过测量X射线衍射得到.对于具有相同阱垒厚度的超晶格,例如4nm/4nm,5nm/5nm,8nm/8nm的GaN/Al_0.3Ga_0.7N超晶格,研究发现随着超晶格周期厚度的增加Al_xGa_1-xN外延薄膜缺陷密度降低,Al_xGa_1-xN外延薄膜处于张应变状态,且5nm/5nmGaN/Al_0.3Ga_0.7N超晶格插入层Al_xGa_1-xN外延薄膜的张应变最小.在保持5nm阱宽不变的情况下,将垒宽增大到8nm,即十个周期的5nm/8nmGaN/Al_0.3Ga_0.7N超晶格插入层使Al_xGa_1-xN外延层应变状态由张应变变为压应变.由X射线衍射结果计算了Al_xGa_1-xN外延薄膜的刃型位错和螺型位错密度,结果表明超晶格插入层对螺型位错和刃型位错都有一定的抑制效果.透射电镜图像表明超晶格插入层使位错发生合并、转向或是使位错终止,且5nm/8nmGaN/Al_0.3Ga_0.7N超晶格插入层导致Al_xGa_1-xN外延薄膜中的刃型位错倾斜30°左右,释放一部分压应变.     

InGaN蓝光与CdTe纳米晶基白光LED

报道了倒装焊InGaN蓝光LED与黄光CdTe纳米晶的复合结构。利用蓝光作为CdTe纳米晶的激发源,通过光的下转换机制,将部分蓝光转化为黄光,复合发射出白光。室温下正向驱动电流为10mA时,发光色品坐标为x=0.29,y=0.30。实验表明,该复合结构白光LED的一大优点在于,复合光的色品坐标几乎不随正向驱动电流大小变化,颜色稳定。     

大尺寸HVPE反应器寄生沉积的数值模拟研究

在氢化物气相外延(HVPE)生长GaN厚膜中,反应腔壁面总会产生大量的寄生沉积,严重影响薄膜生长速率及质量.本文针对自制的大尺寸垂直式HVPE反应器,通过数值模拟与实验对比,研究了反应腔壁面沉积以及GaN生长速率的分布规律,特别是寄生沉积分布与载气流量的关系.研究发现:在基准条件下,顶壁寄生沉积速率由中心向边缘逐渐降低,与实验结果吻合;侧壁沉积出现8个高寄生沉积区域,对应喷头边缘处排布的GaCl管,说明沉积主要取决于GaCl的浓度输运;模拟得出的石墨托表面生长速率低于实验速率,但趋势一致.保持其他条件不变,增大NH3管载气N2流量,顶壁和侧壁的寄生沉积速率及分布区域均随之增大,石墨托表面生长速率随之减小而均匀性却随之提高;增大GaCl管载气N2流量,顶壁和侧壁的寄生沉积速率及分布区域均随之减小,石墨托表面生长速率随之增大而均匀性却随之降低.研究结果为大尺寸HVPE反应器生长GaN的工艺优化提供了理论依据.     

TiAl3 和Ti/TiAl3 非合金化电极n型GaN欧姆接触的实现

在不进行合金化的情况下,首次直接采用TiAl3合金材料作为金属接触电极.在蓝宝石衬底上生长的n型载流子浓度为2×1018 cm-3的GaN上,成功地得到低接触电阻的欧姆接触,并由环形传输线模型方法测得比接触电阻率为3×10-5 Ω*cm2.与通常n型欧姆接触采用的Ti/Al双层结构比较,TiAl3合金结构更容易形成非合金化的n型欧姆接触.在此实验基础上,进一步分析了N空位和界面层处的TiAl3在形成非合金化或低温退火欧姆接触中发挥的作用,由此设计的Ti/TiAl3/Ni/Au接触结构,在TiAl3合金结构基础上明显地降低了接触电阻率.     

In气氛下晶体生长对Mg掺杂p-Al_xGa_(1-x)N激活能的影响

Ⅲ-Ⅴ族氮化物宽禁带半导体材料体系中,普通方法生长的p型外延层电导率一般都很低,成为了制约器件性能提高的瓶颈。在p-AlxGa1-xN材料中,Mg受主的激活能较大,并且随Al组份增加而增大。通过在p-AlxGa1-xN材料生长过程中引入三甲基铟(TMIn),发现能有效地降低AlxGa1-xN材料中受主态的激活能。为研究不同In气氛下生长的p-AlxGa1-xN材料的性质,在使用相同二茂基镁(CP2Mg)的情况下,改变TMIn流量,生长了A,B,C和D四块样品。X射线衍射(XRD)组份分析表明:在1100℃下生长AlxGa1-xN外延层时,In的引入不会影响晶体组份。利用变温霍尔(Hall)测试研究了p-AlxGa1-xN材料中受主的激活能,结果表明:In气氛下生长的外延层相比无In气氛下生长的外延层,受主激活能明显降低,电导率显著提高。采用这种方法改进深紫外发光二极管(LED)的p-AlxGa1-xN层后,LED器件性能明显提高。     

Effect of Interface Nanotexture on Light Extraction of InGaN-Based Green Light Emitting Diodes

We report the enhancement of the light extraction of InGaN-based green light emitting diodes （LEDs） via the interface nanotexturing. The texture consists of high-density nanocraters on the surface of a sapphire substrate with an in situ etching. The width of nanocraters is about 0.5 μm and the depth is around 0.1 μm. It is demonstrated that the LEDs with interface texture exhibit about a 27% improvement in luminance intensity, compared with standard LEDs. High power InGaN-based green LEDs are obtained by using the interface nanotexture. An optical ray-tracing simulation is performed to investigate the effect of interface nanotexture on light extraction.     

Effects of Ⅴ/Ⅲ ratio on species diffusion anisotropy inthe MOCVD growth of non-polar a-plane GaN films

Non-polar a-plane (110) GaN films have been grown on r-plane (102) sapphire substrates by metal organic chemical vapour deposition. The influences of Ⅴ/Ⅲ ratio on the species diffusion anisotropy of a-plane GaN films were investigated by scanning electron microscopy, cathodoluminescence and high-resolution x-ray diffraction measurements. The anisotropy of a-plane GaN films may result from the different migration length of adatoms along two in-plane directions. Ⅴ/Ⅲ ratio has an effect on the growth rates of different facets and crystal quality. The stripe feature morphology was obviously observed in the film with a high V/III ratio because of the slow growth rate along the [100] direction. When the Ⅴ/Ⅲ ratio increased from 1000 to 6000, the in-plane crystal quality anisotropy was decreased due to the weakened predominance in migration length of gallium adatoms.