荧光红-曙红Y能量转移及荧光猝灭法测定痕量铜(Ⅱ)的研究

在λex／λem=404．7／550nm,乳化剂OP存在下,荧光红-曙红Y能够发生有效能量转移,使曙红Y荧光强度大大提高;在pH6．5～7．6的KH2PO4-NaOH缓冲溶液中,Cu(Ⅱ)与曙红Y和邻菲罗啉形成配合物,使曙红Y的荧光猝灭,从而建立了测定痕量铜的荧光分析新方法。铜含量在0～250μg／L范围内与曙红Y的荧光猝灭程度呈良好的线性关系。方法的检出限为0．82μg／L;测定100μg／L铜溶液,其RSD为4．6％(n=11);样品加标回收率为102．1％～105％。本法用于人发、茶叶和大米中痕量铜的测定,结果满意。     

双席夫碱双-(2,4-二羟基苯乙酮)缩肼的合成及其与铜的荧光猝灭反应

报道了一种新的双席夫碱荧光试剂——双—(2，4—二羟基苯乙酮)缩肼的合成；试剂在492.8nm处有一强荧光峰，当有铜离子存在时，可与试剂形成稳定的配合物而使试剂的荧光猝灭；利用此反应建立了一个荧光测定痕量铜的新方法，测定铜的线性范围为0．0～180．0μg／L，检出限0．02μg／L，方法可应用于矿泉水和水中痕量铜的测定。     

四溴荧光素荧光猝灭法测定司帕沙星

基于司帕沙星能够猝灭四溴荧光素的荧光且荧光猝灭程度与司帕沙星的量成正比，建立了一种测定微量司帕沙星的方法。在pH3．5的Clark—Lubs缓冲溶液中，四溴荧光素激发波长λex=485nm、发射波长λem=545nm，司帕沙星的质量浓度在0～2．0mg／L范围内符合比耳定律，方法检出限为42．7μg/L。已用于片剂及胶囊中司帕沙星的测定。6次平行测定回收率为93．8％～104．3％，相对标准偏差为1．1％～2．8％。     

碲化镉纳米晶荧光猝灭法测定痕量铜(Ⅱ)

制备了水溶性的CdTe纳米晶。基于铜（Ⅱ）离子在pH=7,80的磷酸盐缓冲溶液中对该纳米晶的荧光具有较强的猝灭作用,建立了一种测定铜（Ⅱ）离子的新方法。在最佳条件下,体系的相对荧光强度（△F）与铜（Ⅱ）离子的浓度呈线性关系,线性范围为8．0～320．0μg／L,其线性回归方程为：△F=-8．18-0．14c（μg／L）;检出限为3．24μg／L。本方法用于实际样品中痕量铜的测定,结果令人满意。     

新试剂3-对氟苯基-5-（2＇-羧基苯偶氮）若丹宁的合成及荧光法测定铋

合成了新型试剂3-对氟苯基-5．(2’-羧基苯偶氮)若丹宁，并经元素分析、IR确证了其结构。研究发现在pH=5．2时该试剂与痕量铋锄形成的螯合物可使试剂的荧光强度大大减弱，在λex／λem=305nm/404nm处有最大峰；其荧光猝灭值与铋的浓度在1．0-12μg/L范围内呈线性关系，检出限达0．26μ／L。建立了荧光光度法测定痕量铋的新方法。     

利用荧光共振能量转移体系测定食品中NO2-的研究

在λcx/λem=450／580nm，0．1mol／L的HCl溶液中，番红花红T和吖啶橙能够发生有效的共振能量转移，使得番红花红T荧光增强，同时吖啶橙的荧光猝灭，而NO2^-的加入使得两者的荧光强度同时减弱。由此建立了一种新的测定痕量NO2^-的方法。结果表明，NO2^-在0．02～10μg／mL范围内与染料的荧光强度减弱程度呈良好的线性关系，方法检出限为1．73ng／mL；该法用于食品中NO2^-的测定，回收率为105．0％～112．4％。     

氯酚类物质测定新方法及其与人血清白蛋白的相互作用

建立了氯酚类物质（CPs）新的检测方法，通过光谱学特征，探讨了CPs与人血清白蛋白（HSA）的结合反应机制。以2，4-二氯苯酚（2，4-DCP）为代表，考察了溶液酸度、试剂用量、反应温度和反应时间等因素对CPs—HSA体系荧光猝灭强度的影响。由Stern—Volmer方程求出2，4-DCP与HSA的猝灭常数（Kq）及反应热力学参数。结果表明，方法线性范围为0．075～0．65mg／L，检出限为0．226μg／L（以2，4-DCP计）。该方法与C18柱固相萃取技术相结合，用于水中CPs的测定，相对标准偏差小于2．9％，加标回收率为96％～106％。对荧光猝灭机理的探讨结果表明，2，4-DCP致HSA内源荧光猝灭以静态猝灭为主。     

三元杂多酸荧光猝灭测定食品中硼砂的研究

研究发现,硼钼杂多酸能与罗丹明B形成缔合物,导致罗丹明B的荧光发生静态猝灭,以此建立了荧光猝灭测定痕量硼砂的新方法.在选定的实验条件下,当λex/λem=540/582 nm,硼砂浓度在2.4～108μg/L范围内时,荧光猝灭强度与硼砂含量呈良好线性关系(r=0.9982),检出限为1.42μg/L,加标回收率在91.3%～101%之间,相对标准偏差(RSD)<3.76%.该方法用于食品中痕量硼砂的测定,结果满意.     

基于锰掺杂量子点的噁喹酸荧光共振能量转移检测研究

基于噁喹酸对锰掺杂硫化锌量子点的荧光猝灭作用,建立了一种噁喹酸荧光共振能量转移检测方法。噁喹酸对量子点的荧光猝灭是由于生成了新的复合物而造成的静态猝灭,二者相互作用过程中焓变ΔH<0,熵变ΔS<0,分子间作用力为氢键或范德华力。在0~65μg/L线性范围内,噁喹酸质量浓度与量子点荧光抑制率呈现良好的线性关系(R²=0.9911),检出限为0.53μg/L。分别在5μg/L和25μg/L 2个浓度进行加标回收,平均加标回收率为92.2%~96.8%,相对标准偏差为0.6%~2.5%。该方法可应用于水环境中喹啉酮类杀菌剂噁喹酸的快速测定。     

液膜分离富集二甲氧基羟基苯基荧光酮荧光猝灭法测定微量钼的研究

研究了在pH5．0～6．4的HAC-NaAC缓冲介质中和CTMAB存在下,Mo(Ⅳ)对二甲氧基羟基苯基荧光酮(DMH-PF)的荧光猝灭效应,建立了荧光猝灭法测定微量Mo(Ⅳ)的新体系,DMH-PF最大激发波长为λex=514nm、最大发射波长为λem=547nm,DMH-PF与Mo(Ⅵ）形成1：2配合物使荧光猝灭,荧光猝灭量与Mo(Ⅵ)在0～0．072mg／L范围内呈线性关系,方法的检出限为0．0022mg／L,体系稳定,灵敏度高,采用液膜分离富集钼,可应用于合金钢和石墨中微量钼的测定。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.