动态液相微萃取-气相色谱法测定水样中有机磷农药残留

建立了水样中敌敌畏、二嗪农、毒死蜱、甲基对硫磷和对硫磷等5种有机磷农药的动态液相微萃取-气相色谱检测方法。实验表明甲苯是良好的萃取溶剂，甲苯体积为2μL时达到最佳萃取效果。液相微萃取是一种非平衡萃取过程，随着萃取次数的增加，萃取效率不断提高，本研究选择萃取次数为25次。在优化的实验条件下，各目标物的萃取富集倍数为21-60；回收率0．85％-2．38％之间；方法的检出限为0．1-0．3μg／L；基体加标检测的相对标准偏差(RSD)为4．9％-8．0％。本方法可用于水体中痕量有机磷农药的富集检测。     

微波辅助萃取-固相微萃取联用气相色谱-质谱法测定土壤中的扑草净

研究了微波辅助萃取-固相微萃取联用、气相色谱-质谱联用测定土壤中除草剂扑草净的分析方法。采用正交设计实验优化了萃取溶剂种类和体积、微波辐射时间和微波功率等微波辅助萃取条件;研究了SPME萃取涂层、搅拌速度、萃取时间和解吸时间等对萃取效率的影响。方法的检出限为0．01ng／g;线性范围为0．2—200μg／L。在优化的条件下测定了5和50ng/g的合成土壤样品,回收率分别为90．1％和91.6％;相对标准偏差分别为9．4％和8．8％(n=6)。本法综合了微波辅助萃取和固相微萃取的优点,操作简便．灵敏度高,特别适合于固体样品中痕量有机物的萃取分离。     

浊点萃取-火焰原子吸收光谱法测定催化剂中痕量钯的研究

研究了以1-（2-吡啶偶氮）-2-萘酚（PAN）为络合剂，以非离子型表面活性刺Triton X-100为萃取剂的浊点萃取分离富集-火焰原子吸收光谱法测定痕量钯的新方法。详细考察了溶液的pH、络合剂和表面活性剂浓度、平衡温度和时间等条件对浊点萃取效果的影响。该方法对钯的检出限为30．8ng／mL，相对标准偏差（RSD）为2．1％（n=10），回收率在97．8％-106．6％之间。可用于催化剂中Pd（Ⅱ）的测定。     

GC-MS法测定纺织品中16种邻苯二甲酸酯含量

采用超声萃取方法提取样品,建立了纺织品中16种邻苯二甲酸酯增塑剂含量测定的气相色谱-质谱（GC-MS）检测方法。以甲醇为萃取剂超声波辅助萃取,考察了超声萃取的温度和时间。在选定试验的条件下,当添加邻苯二甲酸酯类浓度为2～40mg／L时,该方法的加标回收率为84．7％-106．2％,测定结果的相对标准偏差（RSD）在1．8％～7．4％之间（n=7）.     

固相萃取搅拌棒萃取-气相色谱分析海水中的多环芳烃

利用固相萃取搅拌棒（SBSE）萃取海水中的多环芳烃，然后用热解吸脱附-气相色谱分析。研究了萃取时间、添加NaCl浓度对萃取效率的影响。实验结果表明，SBSE方法对16种多环芳烃的萃取回收率分别在33．5％～122．4％之间；对标准样品的检出限为2．74-13．5ng／L；方法RSD为3．8％～13．1％。用此方法测定了大连海岸海水中的多环芳烃含量。     

顶空固相微萃取-气相色谱-质谱联用分析纺织品中挥发性有机物

建立了顶空固相微萃取（HSSPME）-气相色谱（GC）-质谱（MS）联用测定纺织品中甲苯、4-乙烯基环己烯、苯乙烯、萘和1-苯基环己烯5种挥发性有机物（VOCs）的分析方法。选择聚二甲基硅氧烷（PDMS）作为萃取涂层，优化了SPME的萃取条件，包括平衡时间、萃取时间、萃取温度、顶空体积、离子强度、搅拌速度、解吸温度和时间以及GC—MS仪器条件。对于甲苯、4-乙烯基环己烯、苯乙烯、萘和1-苯基环己烯方法线性范围分别为0．087～870、3．32～3320、2．28～2280、0．015～150和0．050～50．0ng／g；检出限分别为0．005、0．042、0．670、0．008和0．011ng／g。实际样品加标回收率在80．1％～122％之间，RSD在0．8％～8．6％之间。方法符合纺织品中痕量VOCs的快速分析要求。     

加压溶剂萃取和在线检测可吸入固体颗粒物(PM10)中16种多环芳烃

建立了微池加压溶剂萃取（μ-PLE）-气相色谱在线联用测定可吸入固体颗粒物（PM10）中多环芳烃的方法和装置。研究了萃取压力在5～20MPa、萃取温度在50—200℃、萃取时间在2-15min对μ-PLE萃取效率的影响。实验结果表明：方法的回收率在24．3％-63％之间；对标准样品的检出限为2．2-9．5μg／L；对实际样品的检出限在0．01—2．03ng/m^3之间；相对标准偏差（RSD）为1．6％-26．4％。通过对萃取池小型化，利用毛细管气相色谱大体积柱内进样技术，实现了两者的在线联用。将萃取液全部转移到气相色谱中，样品利用率达到80％以上，检出灵敏度比现有样品预处理方法提高100倍以上，可以监测大气颗粒中短时间化学变化的有机成分。     

磷酸三丁酯萃取火焰原子吸收法间接测定植物和煤灰中的痕量锗

本文报道了磷酸三丁酯萃取-火焰原子吸收法间接测定植物及煤灰样品中痕量锗的新方法。锗与钼酸铵在0．3mol／L的硝酸介质中形成稳定的锗钼杂多酸,被磷酸三丁酯萃取,有机相直接进样测定钼而间接测定锗;特征浓度为21．8ng／mL／1％吸光度,RSD(n=11)为4．6％,加标回收率为97．6％～101．2％。     

饲料中克伦特罗和沙丁胺醇分离方法的研究

研究了用液-液萃取和固相萃取两种方法同时分离饲料中克伦特罗和沙丁胺醇．液．液萃取法中，采用乙酸乙酯 正己烷 异丙醇混合溶剂，克伦特罗和沙丁胺醇萃取率分别可达85．20％、83．00％：固相萃取法中，采用Amberlite XAD-2大孔吸附树脂，效果较液．液萃取更好。萃取率为91．25%和86．10％．两种分离方法用于饲料中克伦特罗和沙丁胺醇的测定。结果满意．     

超临界CO2流体萃取辛夷精油的组分分析

采用超临界CO2流体萃取辛夷精油,萃取率为3．8％,比水蒸气蒸馏的萃取率高58％。利用气相色谱-质谱联用(GC-MC)法对辛夷精油进行组分的定性和定量分析,并与水蒸气蒸馏法所得辛夷精油的组分相比较,发现超临界CO2流体萃取所得辛夷精油的香气、品质、产率优于水蒸气蒸馏法所得辛夷精油。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.