硫酸盐体系三价铬沉积机理及镀层表征

在新研发的硫酸盐三价铬镀厚铬的镀液体系中, 运用线性扫描伏安法(LSV)和循环伏安法(CV)对三价铬在铜电极表面的电沉积过程进行研究, 并运用X射线荧光测厚仪、扫描电子显微镜(SEM)、X射线能量色散谱(EDS)、X射线衍射仪(XRD)、显微硬度计和Tafel曲线表征铬镀层厚度、形貌、组成、结构、显微硬度及在3.5wt% NaCl溶液中的耐蚀性. 结果表明, 在该体系中三价铬的沉积过程分两步进行(Cr³⁺ + e →Cr²⁺ , Cr²⁺ + 2e → Cr), 第一步得到1个电子, 受电化学过程和扩散过程共同控制, 第二步得到2个电子, 为扩散控制下的不可逆过程; 该镀层为瘤状纳米晶结构, 镀层中含有少量的铁元素(1.10 wt%), 显微硬度达到789.2 Hv, 镀层在3.5wt% NaCl溶液中的腐蚀电位(E_corr)为-0.29 V, 腐蚀电流密度(j_corr)为9.26×10^-5 A·dm^-2.     

1-丁基-3-甲基咪唑硫酸氢盐与乙酸钠混合电解液中三价铬电镀的研究

本文研究了Cr³⁺在1-丁基-3-甲基咪唑硫酸氢盐（[BMIM]HSO₄）电解液中的电沉积反应以及添加剂NaOAc对电镀铬的影响. 含Cr³⁺电解液的循环伏安结果表明,Cr(III)还原为Cr(II)的峰电位是-1.5 V (vs. Pt), 峰电位和峰电流均满足Rendle-Sevcik扩散方程,由该方程计算得到Cr³⁺的扩散系数为1.6 × 10^-8 cm²·s^-1. 铬镀层的X射线衍射和扫描电子显微镜表征结果表明镀层由纳米球状的单质铬颗粒聚集而成,其平均粒径为0.87μm. 在电解液中添加NaOAc后,Cr³⁺的还原峰电位正移了约0.25 V. 同时EDS结果表明,在NaOAc的作用下镀层中Cr/O摩尔比由4.48增加至6.28,这说明OAc^-有利于单质铬的电沉积. 当电解液中NaOAc-[BMIM]HSO₄-CrCl₃-H₂O的摩尔比为0.075:1:0.5:6时,所得的镀层最厚(63 μm)与电流效率最高(33.5%).     

高择优取向铜镀层的电化学形成及其表面形貌

采用电化学方法在H2SO4-CuSO4电解液中获得高择优取向的Cu电沉积层.XRD结果表明,在1.0 ～6.0和15.0 A•dm－2的电流密度下可分别获得(220)和(111)晶面高择优取向的Cu镀层.在同一电流密度下获得的Cu电沉积层织构度随镀层厚度增大而提高.SEM结果表明,在4.0和15.0 A•dm－2的电流密度下可分别获得(220)和(111)织构Cu沉积层,其表面形貌在(220)晶面取向时呈现为细长晶粒连结成的网状，在(111)取向时则呈六棱锥状.提出了可能的机理，认为电流密度变化引起的Cu镀层择优取向晶面的转化归因于电结晶晶面生长方向及生长速度竞争的结果.     

高择优取向Cu电沉积层的XRD研究

采用电化学和XRD方法在CuSO4 +H2 SO4 电解液中获得Cu电沉积层并研究其结构 .结果表明 ,在 4 .0A/dm2 和 15 .0A/dm2 电流密度下可分别获得 (2 2 0 )和 (111)晶面高择优取向Cu镀层 ;Cu镀层晶面织构度随厚度提高而增大 ,获得 (111)晶面高择优Cu镀层的厚度约是 (2 2 0 )晶面的 7倍 ,说明Cu(2 2 0 )晶面比 (111)晶面是更易保留的晶面 ,且低电流密度下铜的电结晶更容易受电沉积条件控制 ;较高的沉积电流密度有利于晶核的形成 ;Cu镀层存在晶格畸变和晶胞参数的涨大     

硝酸铈及热处理对化学镀Ni-W-P合金的性能影响

为提高化学镀Ni-W-P镀层的耐蚀性和耐磨性,拓宽其应用,采用电化学方法和热处理等手段,研究了镀液中添加剂硝酸铈(Ce(NO3)3)的质量分数和热处理对化学镀Ni-W-P镀层的沉积速度、孔隙率、失重腐蚀速度、腐蚀电位、腐蚀电流、交流阻抗、显微硬度、摩擦系数等性能的影响。结果表明:添加1.0 wt%Ce(NO3)3时,所得镀层的沉积速度最大(36.5 g/m2·h),孔隙率最低(0.8个/cm2),耐腐蚀性能最好。镀层的组织均匀、致密、无缺陷和非晶态结构是其耐蚀性能高的重要原因。100~600℃热处理后,镀层硬度和耐磨性有所提高,而400℃热处理之后,合金显微硬度高达1100 HV,是镀态的1.8倍。     

钇对Zn-Fe合金镀层耐蚀性的影响

电镀液中加入钇盐,在A3钢表面电镀Zn-Fe合金薄膜,研究了钇对Zn-Fe合金镀层耐蚀性能的影响.用线性扫描伏安法和交流阻抗法,研究Zn-Fe合金镀层在30℃0.20 mol·L-1H2SO4溶液中的腐蚀行为.用XRD和SEM研究zn-Fe合金镀层在腐蚀前后的微观结构和形貌的变化.结果表明:加入钇盐,能改变Zn-Fe合金镀层的晶面择优取向和织构系数,使结晶粒度变小,且低晶面指数的晶面耐蚀性较好;当加入钇盐量为0.60 g·L-1时,镀层变得均匀、致密,电结晶生长形态变为层状;镀层的致钝电流密度(ipp)和维钝电流密度(ip)降低显著,极化电阻Rp增大,获得的Zn-Fe合金镀层的耐蚀性能最好.     

不同碱液单晶硅表面织构的初步研究(英文)

分别以氢氧化钠(NaOH)、碳酸钠(Na2CO3)和磷酸钠(Na3PO4.12H2O)作为刻蚀剂,研究刻蚀浓度、温度(θ)、刻蚀时间(te)和添加剂(异丙醇(IPA)、碳酸氢钠(NaHCO3))对晶体硅表面织构化的影响,用场发射扫描电子显微镜表征织构效果.通过优化工艺,可得到较低的平均表面反射率(Rav),按使用的刻蚀剂分别为:9.70%(NaOH)、9.76%(Na2CO3)和8.63%(Na3PO4.12H2O).据此分析了Rav和织构表面形貌之间的关系.发现添加剂IPA在Na3PO4.12H2O或Na2CO3与NaOH 3种刻蚀剂溶液中均可明显起改善织构效果.NaHCO3在某些方面具有与IPA的相同作用,同时又能促进大金字塔的形成.文中同时初步提出有关刻蚀过程的机理.     

代铬镀层的研究进展

六价铬会严重破坏环境并危害人类的健康,所以开发无六价铬的代铬镀层电镀工艺具有重要的现实意义。本文主要介绍了几种代铬镀层的研究进展,包括合金代装饰铬镀层、电镀及化学镀合金代硬铬镀层以及复合镀代铬镀层等,重点论述了其特点、典型电镀工艺及其应用,并结合其研究现状对代铬镀层的发展进行了展望。     

从三价铬镀液中电沉积可替代硬铬镀层的铬合金镀层

为了解决目前三价铬镀铬技术的一些致命缺陷，使三价铬镀铬能够最终全面取代六价铬镀铬，近几年来作者进行了大量探索性试验，逐步确定了用电镀非晶态铬合金镀层代替纯铬镀层的技术路线，并开发成功了从三价铬镀铬中电镀非晶态Ｃｒ－Ｆｅ－Ｃ合金镀层的工艺，该镀层在耐磨蚀性等主要性能上保持了传统六价铬镀层的水平，彻底消除了六价铬电镀所造成的严重环境污染问题，并在工艺性能，生产成本等方面与现有的三价铬镀铬技术相比具备一     

硝酸铬与组氨酸配合行为的相化学与热化学研究

用相平衡方法研究了硝酸铬-组氨酸-水体系在298.15K时的溶度,绘制了体系的相图,发现并制备了文献未报道的一致溶解配合物:Cr(His)(NO3)3·3H2O(A),Cr(His)2(NO3)3·3H2O(B)和Cr(His)3(NO3)3·3H2O(C),经分析确定了其组成。用微热量计热测定了硝酸铬和组氨酸在水中的反应焓,计算了这些反应的热动力学参数(活化焓、活化熵及活化自由能)、速率常数和动力学能数(活化能、指前因子及反应级数)。     

吡咯并[2,1,5-cd]中氮茚酰腙衍生物的合成及Cu2+荧光探针行为

设计合成了吡咯并[2,1,5-cd]中氮茚酰腙衍生物6. 测试了其紫外光谱和荧光光谱, 研究了其对铜离子的选择性识别作用. 结果表明, 化合物6作为铜离子荧光探针, 受常见离子干扰较小, 对于铜离子有着较高的选择性和较低的检出限.     

A potentiometric rhodamine-B based membrane sensor for the selective determination of chromium ions in wastewater.

The construction and performance characteristics of a novel chromate ion-selective membrane sensor are described and used for determining chromium(III) and chromium(VI) ions. The sensor is based on the use of a rhodamine-B chromate ion-associate complex as an electroactive material in a poly(vinyl chloride) membrane plasticized with o-nitrophenyloctyl ether as a solvent mediator. In a phosphate buffer solution of pH 6 - 7, the sensor displays a stable, reproducible and linear potential response over the concentration range of 1 x 10(-1) - 5 x 10(-6) mol l(-1) with an anionic Nernstian slope of 30.8 +/- 0.5 mV decade(-1) and a detection limit of 1 x 10(-6) mol l(-1) Cr(VI). High selectivity for Cr(VI) is offered over many common anions (e.g., I-, Br-, Cl-, IO4-, CN-, acetate, oxalate, citrate, sulfate, phosphate, thiosulfate, selenite, nitrate) and cations (e.g., Ag+, Ca2+, Sr2+, Co2+, Ni2+, Cu2+, Mn2+, Fe2+, Zn2+, Cd2+, Al3+, Cr3+). The sensor is used for determining Cr(VI) and/or Cr(III) ions in separate or mixed solutions after the oxidation of Cr(III) into Cr(VI) with H2O2. As low as 0.2 microg ml(-1) of chromium is determined with a precision of +/-1.2%. The chromium contents of some wastewater samples were accurately assessed, and the results agreed fairly well with data obtained by atomic absorption spectrometry.     

[NiFe/Cu/Co/Cu]n纳米多层线的电化学制备及表征

采用电沉积法,在阳极氧化铝(AAO)模板中制备了[NiFe/Cu/Co/Cu]_n多层纳米线.利用扫描电子显微镜(SEM)及透射电子显微镜(TEM)对纳米多层线的表面形貌及结构进行了表征,纳米线阵列高度有序、直径均一、层状结构清晰,NiFe层厚度约40 nm,Cu层厚度约60 nm,Co层厚度约15 nm,各子层厚度可控.利用X射线能谱分析仪(EDS)对纳米多层线NiFe层的成分进行了测试,Ni,Fe的原子比为4:1.利用X射线衍射仪(XRD)对[NiFe/Cu/Co/Cu]_n纳米多层膜和多层线结构进行了测试,多层膜为面心立方(fcc)结构,多层线NiFe层为面心立方(fcc)结构,Cu层为六方密排hcp(100),Co层为面心立方(fcc)结构.与组成、结构完全相同的多层膜相比,[NiFe/Cu/Co/Cu]_n多层纳米线具有更优越的巨磁电阻性能.     

非育珠背角无齿蚌软组织微量元素含量的分析

采用高频电感耦合等离子体发射光谱(ICP—AES)法测定了非育珠背角无齿蚌软组织中锰(Mn)、铁(Fe)、锌(Zn)、铬(Cr)、铝(Aj)、铜(Cu)六种微量元素及钙(Ca)、镁(Mg)的含量，分析了各种元素在不同软组织中的分布特征。结果表明：(1)在软组织中，各元素平均含量由高到低依次为：Ca，Mn，Mg，Fe，Zn，Al，Cr，Cu；(2)背角无齿蚌不同软组织中微量元素的含量不同，其中瓣鳃和外套膜中所测元素含量高于其他器官，特别是Mn，Fe的含量最高；Mn的含量甚至超过了宏量元素Mg；Al是闭壳肌中含量最丰富的微量元素。     

Determination of trace elements in iron by neutron-activation techniques

A systematic analytical procedure for the determination of some trace impurities in iron matrices was developed by employing both direct and destructive neutron-activation techniques. Irradiations in fast neutron fluxes, selective activation by epithermal neutrons and coincidence γ-spectrometry measurements were used in some cases, in order to improve the sensitivity for non-destructive analysis; for destructive methods, radiochemical separations based on ion exchange and solvent extraction were applied. Procedures are described, and some results of the determination of low concentrations of Al, Mn, Ti, V (non-destructive), P, S, Zn (destructive) and As, Co, Cr, Cu, Mo, Ni, Sc, W (both methods) in iron are reported and discussed.     

Determination of impurities in nuclear fuel element components by neutron activation analysis

Neutron activation analysis methods for the determination of impurities in zirconium cladding material and uranium oxide are described. Detection limits for the elements Al, Cd, Cr, Co, Cu, Hf, Fe, Mn, Ni, W and U in zirconium are below that required by the ASTM B 352-79 standard. The method has been tested on the NIST SRM 360a Zircaloy-2 from which the elements Na, Mg, Al, Ca, V, Cr, Fe, Co, Ni, Cu, Eu and U have been detected. The values for Cr, Fe, Ni and Cu are compared with the certified values. A method for the pre-irradiation separation of the elements Mg, Na, Al, K, Sc, Ca, V, Mn, Cr, Fe, Co, Cu, Zn, Rb, Zr, Cd, Cs, REE and Hf from uranium has been developed. A neutron activation analysis method for the determination of those elements in uranium is described. The method is tested by the analysis of the IAEA reference sample SR-54/64. The elements Al, Mn, V, Cu, Cr, Co, Ni and Fe have been detected and the results compared with the certified values.     

1-乙酰基-3-(2-羟基-4,6-二甲氧基苯基)-5-苯基-2-吡唑啉的合成及锌离子探针的研究

设计合成了1-乙酰基-3-(2-羟基-4,6-二甲氧基苯基)-5-苯基-2-吡唑啉(4), 测试了其紫外光谱和荧光光谱, 研究了其对锌离子的选择性识别作用. 结果表明, 化合物4作为锌离子荧光探针, 受常见离子的干扰较小, 对于锌离子有着较高的选择性和较低的检出限.     

Electrodeposition of aluminum on magnesium alloy in aluminum chloride (AlCl3)–1-ethyl-3-methylimidazolium chloride (EMIC) ionic liquid and its corrosion behavior

A dense and adhesive Al layer was successfully electrodeposited on a Mg alloy in aluminum chloride–1-ethyl-3-methylimidazolium chloride ionic liquid. The corrosion resistance of the uncoated and Al-coated samples was evaluated by electrochemical impedance spectroscopy and potentiodynamic polarization measurements in 3.5 wt% NaCl solution. It was confirmed that the protective Al layer significantly reduces the corrosion rate of the Mg alloy. However, the deposition potential was a crucial factor that governed the structure and therefore the protection capability of the Al layer.     

甲烷部分氧化制合成气Ⅱ．镍系催化剂的反应性能

主要用第四周期金属元素的氧化物与Ａｌ２Ｏ３的复合氧化物催化剂上甲烷氧化的结果证实了催化剂设计中的预测：（１）催化剂首先应能解离活化甲烷，（２）催化剂要能较快地活化Ｏ２分子．只有同时满足这两个条件，催化剂才可能有较好的甲烷部分氧化活性．第四周期元素中只有镍具有这样的性质．Ｃｕ，Ｍｎ，Ｃｒ，Ｌａ，Ｃａ，Ｚｎ等氧化物的添加可明显提高Ｎｉ－Ａｌ２Ｏ３催化剂的甲烷部分氧化性能，其中Ｃｕ的助催化性能最好．催化剂ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３，ＮｉＯ－ＭｎＯ－Ａｌ２Ｏ３，ＮｉＯ－Ｃｒ２Ｏ３－Ａｌ２Ｏ３的反应活性和选择性顺序，与金属Ｃｕ，Ｍｎ，Ｃｒ上ＣＯ和Ｈ２脱附的顺序是一致的     

浸渍硅胶薄层色谱板分离钴和镍及数字图像分析法定量(英文)

Thin layer chromatography(TLC) of cobalt and nickel has been performed on silica gel layers induced with alkali mediated cellulose extract.A novel combination of 10% aqueous solutions of Tween-20 and potassium thiocyanate in 1∶1(v/v) was identified as the best mobile phase for the selective separation of Co2+from Ni2+on the impregnated Silica Gel G layers.The chromatographic characteristics of the cations were studied and the limits of detection as well as the limits of quantification for Co2+and Ni2+were determined.The quantitative estimation of the cations was achieved from the digital image analysis of respective chromatograms.The proposed quantitative method was successfully applied with 0-0.50% error for the determination of Co2+from Ni2+in spiked samples of bauxite,soil and rock containing common cations such as Al3+,Fe2+,Ti4+,Zn2+,Mn2+,Cu2+,Cr6+,Mg2+,etc.under the optimized chromatographic conditions.