可生物降解聚[(对羟基苯甲酸甲酯/甘氨酸乙酯)膦腈]的合成及其体外降解

以PCl5和NH4Cl为原料,利用一锅法制备了聚二氯膦腈,通过两步亲核取代反应,分别以甘氨酸乙酯和对羟基苯甲酸甲酯为亲核试剂,合成了混合取代可生物降解聚[(对羟基苯甲酸甲酯/甘氨酸乙酯)膦腈].用核磁共振波谱及红外光谱等对产物结构进行了表征.研究了甘氨酸乙酯和对羟基苯甲酸甲酯的比例及外界环境对所制备的聚膦腈降解性能的影响,并进行了体外降解实验.研究结果表明,通过改变甘氨酸乙酯和对羟基苯甲酸甲酯的比例,可获得一种降解速率可调节的生物降解膦腈聚合物.     

沉淀聚合法制备单分散聚(4-乙烯基吡啶-co-二乙烯基苯/三羟甲基丙烷三甲基丙烯酸酯)聚合物微球

以4-乙烯基吡啶(4-VP)为功能单体、二乙烯基苯(DVB)和三羟甲基丙烷三甲基丙烯酸酯(TRIM)为混合交联剂,偶氮二异丁腈(AIBN)为引发剂,乙腈为反应介质,采用沉淀聚合法制备单分散聚合物微球.考察了共聚单体、溶剂、引发剂等聚合条件对聚合物微球粒径、分散性以及产率的影响.并用扫描电镜(SEM)、激光粒度分析仪、热重分析仪和红外光谱对微球进行了表征.结果表明,聚合物微球的表面形貌和产率可通过改变溶剂体积、单体/交联剂摩尔比和引发剂浓度等因素进行控制.降低乙腈溶液体积、增加DVB摩尔比例及交联剂摩尔比、可增加聚合物粒径及粒度分布均匀性,而聚合物产率随溶剂体积和DVB摩尔比增大而减小,随交联剂摩尔比和引发剂浓度的增加而增加.在最优条件下,即DVB和TRIM两者摩尔比4∶1,单体/交联剂摩尔比1∶5,乙腈用量为5.6 m L(单体和交联剂占介质体积的7%),引发剂浓度为2 wt%~6 wt%(占总反应单体的量)时,可获得形貌规则、产率较高的单分散poly(4-VP-co-DVB/TRIM)微球,微球平均粒径约4.02μm,粒径分布指数(U)为1.013.此外,热重分析结果显示,聚合微球于350℃时开始分解,600℃时失重率达84.9%.     

沉淀聚合法Poly(DVB-co-EGDMA-co-MAA)功能聚合物微球的制备及表征

采用二乙烯基苯-55(DVB-55)和乙二醇二甲基丙烯酸酯(EGDMA)作为混合交联剂,乙腈为溶剂,偶氮二异丁腈(AIBN)为引发剂,以甲基丙烯酸为功能单体采用沉淀聚合法合成了单分散或窄分散的、表面具有羧基的交联聚合物微球,所得微球的粒径变化范围为0.6～3.8μm.通过调节交联剂DVB-55和EGDMA的投料比,可以对微球的粒径、粒径分布、产率、热稳定性以及表面官能团含量进行有效控制.文中对混合交联剂DVB-55与EGDMA比例的改变对微球的粒径、粒径分布以及产率的影响机理给出了理论解释;对DVB和EGDMA的兼容性研究表明,制备的三元聚合物微球的核拥有比投料比稍多的DVB单元,而微球的外层则以在预聚混合物中占更大比例的交联剂为主.     

膜乳化-溶剂挥发法制备表面羧基功能化苯乙烯-马来酸酐共聚物微球

以苯乙烯-马来酸酐共聚物(PSMA)为原料,利用膜乳化-溶剂挥发法,成功制备了表面光滑、尺寸均一的表面羧基功能化聚合物微球.研究表明:将膜乳化法和溶剂挥发法相结合,可以有效提高微球粒径的均一性,乳化剂种类及浓度、连续相流速、分散相中聚合物浓度等参数对微球粒径及粒径分布有显著影响.此外,利用盐酸使微球酸酐基团水解,可以得...     

交联聚膦腈中空微球的可控制备

以分散聚合法制备的聚苯乙烯微球为模板,以六氯环三膦腈、4,4’-二羟基二苯砜为共聚单体,三乙胺为缚酸剂,室温条件下制备出了聚苯乙烯／聚膦腈（核／壳）复合微球,然后用四氢呋喃处理该复合微球,得到聚膦腈中空微球。利用红外光谱、元素分析、扫描电镜及投射电镜对所制备中空微球的结构及形貌进行了表征。结果表明,所制备聚膦腈中空微球...     

T形微反应器共沉淀法制备Mg-Al层状双金属氢氧化物及其粒径可控性

采用T形微反应器通过共沉淀法制备了Mg-Al层状双金属氢氧化物(LDHs)纳米颗粒, 考察了流速、混合盐溶液浓度和温度等对产物粒径及其分布的影响. 实验结果表明, 所制备的LDHs样品的形貌和晶体结构与传统共沉淀法结果一致, 但本方法制备的样品粒径小、分布窄. 随着流速增大, 温度升高, 所合成的LDHs样品平均粒径减小, 分布变窄; 而随着混合盐溶液浓度的增大, 所得LDHs样品粒径增大, 分布变宽.     

聚二乙烯基苯微球的合成及其表征研究

采用分散聚合方法制备了聚二乙烯基苯微球 ,研究了引发剂、稳定剂、单体 溶剂比例和溶剂种类对微球粒径及其分布的影响 ,在适当的条件下可以得到平均粒径较大、粒径分布较窄的微球 .用红外光谱法研究了聚合物微球内稳定剂、悬挂双键以及对位和间位二乙烯基苯含量随聚合过程的进行发生的变化 .测得的微球TG曲线表明 ,聚合物微球具有良好的热稳定性 .     

聚苯氧基膦腈的合成及其电纺纤维的制备

以环状三聚六氯磷腈(HCCP)为原料,采用热开环聚合方法,合成了聚二氯磷腈,再利用亲核取代反应合成了聚苯氧基膦腈(PPPh).采用FT-IR、1H NMR、GPC、DSC、TGA等对所得到的聚合物进行了结构表征和性能测试.通过静电纺丝法制备聚苯氧基膦腈纤维,研究了纺丝液浓度、电场强度、挤出速度等对纤维形态的影响.结果表明,在聚合物溶液浓度为7(wt)%～8(wt)%、挤出速度为0.3～1.0 mL/h、接收距离为20cm、电压为22kV的静电纺丝条件下,可制备纤维直径为300～800 nm的PPPh纤维.     

高强度聚乙烯醇水凝胶微球的制备

以三氯甲烷/丙酮为凝固液, 用高压静电技术制备了高强度、物理交联的聚乙烯醇(PVA)水凝胶微球. 研究了凝固液组成、PVA溶液浓度、温度和湿度、电场强度、进样速度及微球冷冻次数等对PVA微球的形貌、粒径和强度的影响. 结果表明, 采用常压水蒸气控制PVA溶液温度与湿度的高压静电技术, 可克服高浓度PVA溶液在强电场下出现微丝现象, 形成的水凝胶微球具有强度高、粒径在一定范围内可控的特点.     

高热稳定性聚膦腈亚微米球的室温快速合成

以六氯环三膦腈（HCCP）和4,4′-二羟基二苯砜（BPS）为共缩聚单体,乙腈为溶剂,三乙胺为缚酸剂,在室温条件下,采用沉淀聚合的方法快速合成了一种聚膦腈亚微米球。 红外光谱、元素分析及X射线能谱分析(EDX)测试表明,该聚膦腈亚微米球具有高度交联的化学结构;扫描电子显微镜和透射电子显微镜测试表明,该聚膦腈亚微米球粒径分布在410 nm附近,而且具有光滑的表面和实心的结构;热重分析(TGA)测试表明,该聚膦腈亚微米球的热分解温度达到531 ℃。 并推测了该聚膦腈亚微米球的形成机理。     

Nucleophilic cosubstitution of poly(dichlorophosphazene) with alkyl ether and amino acid ester

The nucleophilic substitution reaction of poly(dichlorophosphazene) with sodium 2‐methoxyethoxide and glycine ethyl ester has been studied in detail. Polymers prepared with different methods have been characterized by ¹H NMR, and the results reveal that the addition sequence of the two nucleophilic reagents is an important factor in determining the structure of the resultant polymer. If alkyl ether is added first, the subsequently introduced amino acid ester not only reacts with residual P? Cl but also attacks the alkyl ether side units present by replacing either the whole group or just ? OCH₃. As a result, a new kind of side group (? OCH₂CH₂NHCH₂COOC₂H₅) can be detected in the macromolecule. To obtain polymers with desired compositions {poly[(methoxyethoxy)_x(ethylglycino)_yphosphazene]}, the amino acid ester should be introduced initially to react with poly(dichlorophosphazene), and it should be followed by the alkyl ether. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2417–2425, 2005     

直链淀粉交联氨基酸酯取代聚膦腈杂化材料的制备

利用直链淀粉与甘/丙氨酸乙酯共取代聚膦腈交联, 制得了一种具有网络结构的新型杂化材料. 实验结果表明, 淀粉衍生物上的羟基转变为醇钠后, 可与聚膦腈分子链上的P-Cl键发生亲核取代反应; 所得聚合物膜无明显相分离, 力学性能优于具有相似组成的直链淀粉/聚膦腈共混膜, 表面亲水性和吸水率与对应的共混膜接近, 且均高于纯聚膦腈膜. 因此, 该聚合物可作为杂化生物材料用于药物控制释放和组织工程方面的研究.     

Synthesis of biodegradable poly (methylparaben/glycine ethyl ester) phosphazene and further research of its degradation in vitro

Polydichlorophosphazene(PDCP)was synthesized from PCl5 and NH4Cl via a one-pot approach,and then further reacted with glycine ethyl ester and methylparaben via a two-step nucleophilic substitution approach to give poly(methylparaben/glycine ethyl ester)phosphazene(PMGP),which was a kind of mix-substituted biodegradable polymer.NMR and FT-IR were used to characterize its structure.A series of experiments were conducted to study the effects of the ratio of methylparaben to glycine ethyl ester and the experime...     

Molecular Mechanism Study on Effect of Biodegradable Amino Acid Ester–Substituted Polyphosphazenes in Stimulating Osteogenic Differentiation

Amino acid ester substituted polyphosphazenes are osteoactive benefiting from their phosphorus‐containing chemical structure, which highlights interests in bone tissue engineering. To correlate their chemical structures with cell activities, in this study, poly[(ethyl alanato)_0.3(ethyl glycinato)_0.7phosphazene] (PAGP) and poly[(ethyl phenylalanato)_0.3(ethyl glycinato)_0.7phosphazene] (PPGP) are synthesized to carry out studies on cell osteogenic differentiation. In the non‐contact culture manner, bone mesenchymal stromal cells (BMSCs) are cultured in transwell chambers containing PAGP or PPGP films, while the cells and the materials do not contact. In the contact culture manner, BMSCs are cultured on the PAGP or PPGP films. In the meantime, solutions containing PAGP or PPGP degradation products (i.e., phosphate, ammonium, and corresponding amino acids) are applied for cell culture using inorganic phosphate (Pi) ion as control. Thus, the influences from substrate surface and degradation products can be identified separately. The results reveal that both the phosphorus‐containing surface of PAGP and PPGP films and their degradation products play significant roles in regulating cell behaviors. In comparison with PAGP, PPGP seems able to provide relatively stable phosphorus‐containing surface to strengthen the cell‐scaffold interaction because of its slower degradation rate and higher Young's modulus, leading to greater promotion in osteogenic differentiation via contact effect.     

Phase separation of polyphosphazene/poly(lactide‐co‐glycolide) blends prepared under different conditions

Using a mutual solvent technique, blend films of poly[(alaine ethyl ester)_0.62(glycine ethyl ester)_0.38]phosphazene/poly(lactide‐co‐glycolide) (PAGP/PLGA blend) were prepared at different conditions including weight ratios, solvents, environmental humidity, film thickness, and substrates. The morphology and properties of blend films were characterized by scanning electron microscope (SEM), energy dispersive spectrometer (EDX), X‐ray photoelectron spectrometry (XPS), and solvent selective etching. Compared with dichloromethane and tetrahydrofuran (THF), chloroform was the better solvent to form miscible PAGP/PLGA blend films at relatively anhydrous atmosphere. However, in the humid atmosphere, the hexagonal arrangement of holes appeared on the surface of PAGP/PLGA blend films due to the ordered array of water droplets. A sandwich‐liked structure was formed with the hydrophilic PAGP component at the top and bottom, while the PLGA component in the middle. In addition, the surface morphology of PAGP/PLGA blend films was also influenced by the film thickness and the property of the substrate. Copyright © 2010 John Wiley & Sons, Ltd.     

聚[(双-甘氨酸乙酯)膦腈]/聚酯共混相容性研究

采用溶液混合法制备了聚[(双－甘氨酸乙酯）膦腈]（PGP）与丙交酯均聚物（PLA）或丙交酯／乙交酯共聚物（PLGA）的共混体系，利用示差扫描量热仪、傅里叶红外光谱仪和相差显微镜研究了两体系的共混相容性。实验结果表明，PGP与PLA不相容，但通过氢键相互作用可与PLGA达到部分相容，且PGP／PLGA的共混相容性随着PLGA含量的增加而有所改善。     

聚[2-(2-氯乙氧基)乙氧基)_x(三氟乙氧基)_(2-x)]磷腈合成和气体分离性能研究

六氯环三聚磷腈经二次重结晶一次减压升华纯化后,通过真空热开环聚合和亲核取代反应,用不同摩尔比的2-(2-氯乙氧基)乙醇钠和三氟乙醇纳(1∶3;1∶5;1∶6.5)作为亲核取代试剂混取代聚二氯磷腈,再经多次非溶剂沉淀纯化得到目标聚合物聚[(2-(2-氯乙氧基)乙氧基)x(三氟乙氧基)2-x]磷腈.利用31P-NMR监测,以确保得到纯化的聚合物.采用1H-NMR、FT-IR、GPC、DSC、XRD等测试手段对所得到的聚合物进行了结构表征和性能测试,并利用自制的压力法透气性能测定仪测定了这些聚合物的气体渗透系数.结果表明,三氟乙氧基和2-(2-氯乙氧基)乙氧基两种基团已接枝在聚磷腈侧链上,分别得到x值为0.19,0.18和0.08的3种聚[(2-(2-氯乙氧基)乙氧基)x(三氟乙氧基)2-x]磷腈,其玻璃化温度分别为-6.37℃,-12.85℃和-25.68℃,重均分子量为5.4×105,6.8×105和1.5×105,在同样的反应条件下,三氟乙氧基较2-(2-氯乙氧基)乙氧基有更强的竞争取代率.这种混取代聚磷腈较单一取代基的聚三氟乙氧基磷腈结晶度小,在本实验中两种取代基比例适中的聚[(2-(2-氯乙氧基)乙氧基)0.18(三氟乙氧基)1.82]磷腈的结晶度降至10.1%,这种聚合物显示出较高的气体渗透系数,CO2和He的气体渗透系数达到88.9和60.6 barrer,CO2/CH4和He/CH4的选择系数达到24.1和16.4,在天然气行业显露出良好的应用潜力.此外这类聚合物表现出特殊的H2/N2选择性,选择系数在0.2左右,N2的渗透系数为8.5 barrer,因而在合成氨行业显示出特殊的应用潜力.     

氨基酸酯-烷基醚混合取代聚膦腈的合成与表征

聚膦腈高聚物,因其良好的生物相容性而用作生物医用材料。若在其侧链引入对热(如烷氧基醚)或对pH值敏感和可生物降解的基团(如氨基酸酯),则可得到具有环境敏感性和可生物降解性能的高聚物,这些高聚物可望作为药物载体,用于药物的控制释放。     

Synthesis, characterization and hydrolytic degradation of linear and crosslinked poly[(glycino ethyl ester)(allyl amino)phosphazene]

Polyorganophosphazenes substituted by glycino ethyl ester and allylamine with different ratios were synthesized and their structures were characterized by ¹H NMR, ³¹P NMR and FTIR. Via the crosslink reaction, a novel biodegradable crosslinked polyorganophosphazene material was obtained. DSC and FTIR spectra indicated the occurrence of crosslink. Hydrolysis studies were also performed to compare the crosslinked polymers with linear ones. The co-substituted polyorganophosphazenes with more allylamine at pendant groups exhibited a lower degradation rate than poly[bis(glycino ethyl ester)phosphazene] and crosslinked polyphosphazenes had an even lower degradation rate. SEM photographs characterized the surface of polyphosphazenes films after hydrolytic degradation, confirming that uncrosslinked ones had outstanding hydrolytic evidences at the surface while the crosslinked ones only had sporadic small erosion holes, remaining much smoother.