原位退火温度对Mg_2Si薄膜结构及方块电阻的影响

采用磁控溅射法和原位退火工艺在钠钙玻璃衬底上制备Mg_2Si半导体薄膜.首先在钠钙玻璃衬底上依次溅射一定厚度的Si、Mg薄膜,冷却至室温后原位退火4h,在400~600℃退火温度下制备出一系列Mg_2Si薄膜样品.采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)对Mg_2Si薄膜样品的晶体结构和表面形貌进行表征,利用四探针测试仪测试薄膜样品的方块电阻,讨论了原位退火温度对Mg_2Si薄膜结构、表面形貌及电学性能的影响.结果表明,采用原位退火方式成功在钠钙玻璃衬底上制备出单一相的Mg_2Si薄膜,退火温度为550℃时,结晶度最好,连续性和致密性最强,方块电阻最小.这对后续Mg_2Si薄膜器件的设计与制备提供了重要的参考.     

不同衬底和CdCl2退火对磁控溅射CdS薄膜性能的影响

在科宁7059玻璃, FTO, ITO, AZO四种衬底上磁控溅射CdS薄膜, 并在CdCl₂+干燥空气380 ℃退火, 分别研究了不同衬底和退火工艺对CdS薄膜形貌、结构和光学性能的影响. 扫描电子显微镜形貌表明: 不同衬底原位溅射CdS薄膜的形貌不同, 退火后相应CdS薄膜的晶粒度和表面粗糙度明显增大. XRD衍射图谱表明: 不同衬底原位溅射和退火CdS薄膜均为六角相和立方相的混相结构, 退火前后科宁7059玻璃, FTO, AZO衬底上CdS薄膜有 H(002)/C(111) 最强衍射峰, ITO衬底原位溅射CdS薄膜没有明显的最强衍射峰, 退火后出现 H(002)/(111) 最强衍射峰. 紫外-可见分光光度计分析表明: AZO, FTO, ITO, 科宁7059玻璃衬底CdS薄膜的可见光平均透过率依次减小, 退火后相应衬底CdS薄膜的可见光平均透过率增大, 光学吸收系数降低; 退火显著增大了不同衬底CdS薄膜的光学带隙. 分析得出: 上述结果是由于不同衬底类型和退火工艺对CdS多晶薄膜的形貌、结构和带尾态掺杂浓度改变的结果. 关键词： CdS薄膜 磁控溅射 退火再结晶 带尾态     

磁控溅射法结合异位退火制备MgB_2超导薄膜的研究

采用磁控溅射法,结合真空异位退火,成功制备MgB_2超导薄膜,探索了退火温度、退火时间、磁控溅射功率和溅射气压对MgB_2薄膜超导特性的影响。通过XRD、SEM和PPMS测量的结果来分析退火及溅射的工艺参数对MgB_2超导薄膜的晶体结构、表面形貌及超导性能的影响。研究表明,退火温度为670℃,退火时间为2h,MgB_2靶溅射功率控制在300W,Ar溅射气压保持为2Pa,MgB_2薄膜表现出最优的超导特性,其临界电流密度Jc为1.8×105A/cm2。     

磁控溅射制备纳米TiO2半导体薄膜的工艺研究与光谱分析

通过射频反应磁控溅射在玻璃基片上制备TiO2薄膜。采用X射线衍射仪和Raman光谱仪研究退火温度对薄膜晶体结构的影响;还探讨了磁控溅射氧分压对薄膜性能的影响。结果表明：磁控溅射制备的薄膜在不同温度下退火。300℃退火时薄膜没有结晶;400℃退火出现锐钛矿结构;500℃退火后薄膜锐钛矿结构更完善,（101）方向开始优先生长,是因为锐钛矿结构更完整。随着退火温度的升高晶粒长大拉曼光谱出现红移,拉曼光谱所反应的锐钛矿信息增强,500℃退火时197cm-1出现了Eg振动模式。和标准的单晶TiO2体材料相比,拉曼峰位置都略有红移是纳米量子尺寸效应造成的。氩氧比分别为9∶1、7∶3和6∶4溅射制备的薄膜通过400℃退火后的XRD衍射谱没有明显的区别,但拉曼光谱显示氩氧比为7∶3时结晶要完善些。     

高择优取向铌酸锶钡薄膜的射频磁控溅射制备

采用溶胶-凝胶法在(100)Si单晶上预先制备出掺钾(K)的铌酸锶钡(SBN)缓冲层,利用射频磁控溅射法在缓冲层KSBN上沉积出高择优取向的铌酸锶钡薄膜,获得了磁控溅射法制备择优取向铌酸锶钡薄膜的相关工艺参数,研究发现,KSBN缓冲层能够很有效地克服衬底与SBN薄膜之间较大的晶格失配,在氧气氩气的比例为1∶2,工作气压为10 Pa,溅射功率300 W,衬底温度300℃,退火温度为800℃的工艺条件下,能够获得c轴高度择优取向的铌酸锶钡铁电薄膜.利用X射线衍射仪,原子力显微镜等仪器分析了薄膜 关键词： 磁控溅射 高择优取向 p-n结效应     

磁控共溅射低温制备多晶硅薄膜及其特性研究

多晶硅在光电子器件领域具有较为重要的用途。利用磁控溅射镀膜系统,通过共溅射技术在玻璃衬底上制备了非晶硅铝(α-Si/Al)复合膜,将Al原子团包覆在α-Si基质中,膜中的Al含量可通过Al和Si的溅射功率比来调节。复合膜于N₂气氛中进行350 ℃,10 min快速退火处理,制备出了多晶硅薄膜。利用X射线衍射仪、拉曼光谱仪和紫外-可见光-近红外分光光度计对多晶硅薄膜的性能进行表征,研究了Al含量对多晶硅薄膜性能的影响。结果表明：共溅射法制备的α-Si/Al复合膜在低温光热退火下晶化为晶粒分布均匀的多晶硅薄膜;随着膜中Al含量逐渐增加,多晶硅薄膜的晶化率、晶粒尺寸逐渐增加,带隙则逐渐降低;Al/Si溅射功率比为0.1时可获得纳米晶硅薄膜,Al/Si溅射功率比为0.3时得到晶化率较高的多晶硅薄膜,通过Al含量的调节可实现多晶硅薄膜的晶化率、晶粒尺寸及带隙的可控。     

退火温度对原子层沉积法制备ZnMgO薄膜结构和光学性能的影响

针对目前关于退火温度对原子层沉积法(ALD)制备ZnMgO薄膜晶体结构和光学性质影响鲜有报道的现象,进行了相应的实验研究分析。采用ALD在石英衬底上制备ZnMgO合金薄膜,对制得的样品在空气中进行不同温度的退火处理。利用X射线多晶衍射仪(XRD)、光致发光谱(PL)和紫外可见(UV-Vis)吸收光谱测试,系统的分析了不同退火温度对ALD法制备ZnMgO薄膜晶体结构和光学性能的影响。XRD测试结果表明：退火温度为600 ℃时,薄膜的晶体质量得到改善,且(100)衍射峰的强度明显增强。结合PL和UV-Vis吸收光谱的测试分析得出：退火温度为600 ℃时,能明显促进薄膜中Mg组分的增加使薄膜的禁带宽度进一步增大。从而说明适当温度的退火处理可有效的改善ZnMgO薄膜的晶体质量及光学特性。     

单靶溅射制备铜锌锡硫薄膜及原位退火研究

采用衬底加热溅射铜锌锡硫(CZTS)四元化合物单靶制备CZTS薄膜,并研究原位退火对制备薄膜的影响.结果表明:在溅射结束后快速升温并保持一段时间,所得到的样品相比于未原位退火的CZTS薄膜结晶质量更好,且表面更平整致密;原位退火后的CZTS薄膜太阳电池性能参数也相应地有所提升,其开路电压(V_(OC))为575 mV,短路电流密度(J_(SC))为8.32 mA/cm~2,光电转换效率达到1.82%.     

退火处理对磁控溅射制备LaCoO_3薄膜性能的影响

采用磁控溅射法在硅衬底上制备了LaCoO_3(LCO)薄膜,研究了退火温度对LCO薄膜组织结构、表面形貌及热电特性的影响,并利用X射线衍射仪、原子力显微镜(AFM)、激光导热仪等对LCO薄膜的晶体结构、表面形貌、热扩散系数等进行测量与表征.结果表明:退火温度对LCO薄膜的结晶度、晶粒尺寸和薄膜表面形貌都有较大影响;退火前后LCO薄膜的热扩散系数都随温度的升高而减小,且变化速率逐渐减缓; LCO薄膜的热扩散系数随退化温度的升高先增大后减小.LCO薄膜经过700℃退火后得到最佳的综合性能,其薄膜表面致密、平整,结晶质量最好,热扩散系数最小,热电性能最好.     

快速热退火对Co/Si0.85Geo.15肖特基结电学特性的影响

用离子束溅射技术分别在SiO2和单晶Si衬底上沉积了Si1-xGex和Co薄膜.在不同温度下,对Co/Si1-xGex肖特基结进行快速热退火处理(RTA),对处理后的样品进行了表面形貌和电学测量.发现退火温度升高,样品表面粗糙度变大,理想因子也变大,但对肖特基势垒高度(SBH)的影响很小.分析认为,随着退火温度的升高,...     

退火对ZnO薄膜光学特性的影响

用射频磁控溅射法在蓝宝石衬底上制备出ZnO薄膜,通过X射线衍射(XRD)、扫描电镜(SEM)和光致发光(PL)谱等研究了退火温度对ZnO薄膜结构和光学性质的影响。测量结果显示,所制备的ZnO薄膜为六角纤锌矿结构,具有沿c轴的择优取向;随着退火温度的升高,(002)XRD峰强度和平均晶粒尺寸增大,(002)XRD峰半高宽(FWHM)减小,光致发光紫外峰强度增强。结果证明,用射频磁控溅射法通过适当控制退火温度可得到高质量ZnO薄膜。     

真空退火对L1_0-CoPt薄膜结构、磁性及表面形貌的影响

本文利用磁控溅射的方法制备了L1_0-CoPt薄膜,研究了不同退火条件对薄膜结构、磁性以及表面形貌的影响.通过优化退火温度、保温时间以及升温速率,制备出了具有大矫顽力、高矩形比、粗糙度小的垂直各向异性L1_0-CoPt薄膜.实验发现,较高的退火温度有利于克服CoPt薄膜有序化转变所需要的能量,同时适当延长退火时间可以提高CoPt薄膜的扩散系数,从而促使无序相fcc转化为L1_0有序相fct结构.此外,退火过程中减缓升温速率可以有效减小薄膜粗糙度,从而形成平整连续膜.     

Structural and electrical characterization of annealed Si1-xCx/SiC thin film prepared by magnetron sputtering

Si-rich Sil-xCx/SiC multilayer thin films are prepared using magnetron sputtering, subsequently followed by thermal annealing in the range of 800-1200 ℃. The influences of annealing temperature （Ta） on the formation of Si and/or SiC nanocrystals （NCs） and on the electrical characteristics of the multilayer film are investigated by using a variety of analytical techniques, including X-ray diffraction （XRD）, Raman spectroscopy and Fourier transform infrared spectrometry （FT-IR）, current-voltage （I-V） technique, and capacitance-voltage （C-V） technique. XRD and Raman analyses indicate that Si NCs begin to form in samples for Ta _ 800 ~C. At annealing temperatures of 1000 ℃ or higher, the formation of Si NCs is accompanied by the formation of SiC NCs. With the increase in the annealing temperature, the shift of FT-IR Si-C bond absorption spectra toward a higher wave number along with the change of band shape can be explained by a Si-C transitional phase between the loss of substitutional carbon and the formation of SiC precipitates and a precursor for the growth of SiC crystalline. The C-V and I-V results indicate that the interface quality of Si1-xCx/SiC multilayer film is improved significantly and the leakage current is reduced rapidly for Ta ≥ 1000 ℃, which can be ascribed to the formation of Si and SiC NCs.     

退火对多晶ZnO薄膜结构与发光特性的影响

用射频反应溅射法在Si（111）衬底上制备了C轴取向的多晶ZnO薄膜，通过不同温度的退火处理，研究了退火对多晶ZnO薄膜结构和发光特性的影响.由x射线衍射得知，随退火温度的升高，晶粒逐渐变大，薄膜中压应力由大变小至出现张应力.光致发光测量发现，样品在430nm附近有一光致发光峰, 峰的强度随退火温度升高而减弱，联合样品电阻率随退火温度升高而逐渐变大的测量及能级图，推测出ZnO薄膜中的蓝光发射主要来源于锌填隙原子缺陷能级与价带顶能级间的跃迁. 关键词： ZnO薄膜 退火 光致发光 射频反应溅射     

Vanadium oxide thin films deposited on indium tin oxide glass by radio—frequency magnetron sputtering

Highly oriented VO₂(B), VO₂(B) + V₆O₁₃ films were grown on indium tin oxide glass by radio-frequency magnetron sputtering. Single phase V₆O₁₃ films were obtained from VO₂(B) +V₆O₁₃ films by annealing at 480℃ in vacuum. The vanadium oxide films were characterized by x-ray diffraction and x-ray photoelectron spectra (XPS). It was found that the formation of vanadium oxide films was affected by substrate temperature and annealing time, because high substrate temperature and annealing were favourable to further oxidation. Therefore, the formation of high valance vanadium oxide films was realized. The V₆O₁₃ crystalline sizes become smaller with the increase of annealing time. XPS analysis revealed that the energy position for all the samples was almost constant, but the broadening of the V_2p3/2 line of the annealed sample was due to the smaller crystal size of V₆O₁₃.     

溅射气氛和退火方式对硅纳米晶的形成及发光特性的影响

利用磁控溅射技术溅射硅靶,通过调节溅射气氛在硅衬底上生长了SiO/SiO₂超晶格,热退火处理后超晶格中的SiO发生相分离得到硅纳米晶。通过比较不同退火方式对于硅纳米晶的形成的影响发现,管式炉退火处理的样品给出非常强的室温光致发光,其发光峰的峰位随着硅纳米晶尺寸的增大而红移,且管式炉退火比快速热退火更有利于硅纳米晶的形成。     

不同衬底上的ZnO薄膜紫外光致发光

用射频磁控溅射法在蓝宝石、硅和石英衬底上沉积出具有好的择优取向的多晶ZnO薄膜. 在270 nm波长的光激发下室温下可观察到显著的紫外光发射（波长为356 nm）和较弱的蓝光发射（波长为446 nm）. 经高温退火后薄膜的结晶质量显著提高, 在蓝宝石、石英衬底上沉积的薄膜，其积分发光强度分别增加了7倍和14倍.而硅衬底上的膜发光强度增强不太显著.紫外光发射源于电子的带间跃迁，而蓝光发射是由电子从氧空位浅施主能级到价带顶的跃迁引起的. 关键词： ZnO薄膜 射频磁控溅射 紫外发光 退火     

Dependence of microstructure and magnetic properties of FePt/B nanocomposite films on boron content

Compared with previous work, FePt/B nanocomposite films with larger B content in a wide range were prepared by magnetron sputtering plus subsequent annealing on Si (1 0 0) substrates. When the volume percentage is no less than 12%, both interstitial incorporation and intergranular segregation of the B are found, resulting an enlargement of the FePt lattice and a decrease of the FePt grain size. Effect of B content on magnetic properties, such as magnetization, switching field and exchange coupling of the FePt based films, is also discussed.     

Effects of annealing temperature and method on structural and optical properties of TiO2 films prepared by RF magnetron sputtering at room temperature

TiO₂ thin film was deposited on non-heated Si(1 0 0) substrate by RF magnetron sputtering. The as-deposited films were annealed by a conventional thermal annealing (CTA) and rapid thermal annealing (RTA) at 700 and 800 °C, and the effects of annealing temperature and method on optical properties of studied films were investigated by measuring the optical band gaps and FT-IR spectra. And we also compared the XRD patterns of the studied samples. The as-deposited film showed a mixed structure of anatase and brookite. Only rutile structures were found in samples annealed above 800 °C by CTA, while there are no special peaks except the weak brookite B(2 3 2) peak for the sample annealed at (or above) 800 °C by RTA. FT-IR spectra show the broad peaks due to Ti-O vibration mode in the range of 590-620 cm⁻¹ for the as-deposited film as well as samples annealed by both annealing methods at 700 °C. The studied samples all had the peaks from Si-O vibration mode, which seemed to be due to the reaction between TiO₂ and Si substrate, and the intensities of these peaks increased with increasing of annealing temperature. The optical band gap of the as-deposited film was 3.29 eV but it varied from 3.39 to 3.43 eV as the annealing temperature increased from 700 to 800 °C in the samples annealed by CTA. However, it varied from 3.38 to 3.32 eV as the annealing temperature increased from 700 to 800 °C by RTA.