10.6μm激光辐照下光学薄膜的微弱吸收测量

O484.5 2004064370 10.6μm激光辐照下光学薄膜的微弱吸收测量=Measurement of weak absorption of thin film coatings irradiated by 10.6μm laser[刊,中]/杨富(四川大学电子信息学院.四川,成都(610064)),黄伟…∥强激光与粒子束.—2004,16(3).—277-280 建立了表面热透镜技术测量光学薄膜微弱吸收的实验装置,对10.6μmCO_2激光辐照下镀制在Ge基底上的不同厚度的单层ZnS,YbF_3薄膜。以及镀制在Ge基底上不同膜系的(YbF_3/ZnSe)多层分光膜的弱吸收进行了测量,并对实验结果作了分析和讨论。实验结果表明,利用本实验系统已测得的待测样品的最低吸收为2.87×10~(-4),测量系统的灵敏度为10~(-5)。图3表2参6(于晓光)     

射流卷吸微米级结构的图像可视化研究

运用单帧单曝光图像法(SFSEI)对圆管射流的卷吸结构进行了图像可视化研究。单帧单曝光图像法不同于粒子图像测速法(PIV),它是采用相对较长的单次曝光进行拍摄以获得示踪粒子的运动轨迹。实验记录了从射流开始到观测区域内卷吸的形成过程。流场图像的空间大小为6.36 mm×3.97 mm,空间分辨率达到5.3μm×5.3μm。图像记录了射流卷吸产生的精细涡结构,其尺寸分布从几十微米到几百微米。本文的实验结果有助于理解射流的卷吸机理,也表明单帧单曝光图像法可以应用于观测微米级的流动结构。     

溶胶-凝胶光学薄膜的激光损伤研究

 采用溶胶-凝胶工艺制备了SiO₂与ZrO₂单层介质膜，用输出波长1.06μm，脉宽15ns的电光调Q激光系统产生的强激光进行辐照实验。观察了光学薄膜经强激光辐照后的损伤情况，讨论了溶胶 凝胶光学薄膜在强激光照射下的损伤机理，提出了溶剂替换、紫外光处理、添加有机粘接剂等提高溶胶 凝胶光学薄膜激光损伤阈值的方法。     

CVD金刚石中的氮对等离子体刻蚀的影响

采用非对称磁镜场电子回旋共振等离子体分别对沉积过程中掺氮和未掺氮的化学气相沉积金刚石膜进行了刻蚀研究, 结果表明: 掺氮制备的金刚石膜的刻蚀主要集中在晶棱处, 经过4h刻蚀后其表面粗糙度由刻蚀前的4.761 μm下降至3.701 μm, 刻蚀对金刚石膜的表面粗糙度的影响较小; 而未掺氮制备的金刚石膜的刻蚀表现为晶面的均匀刻蚀, 晶粒坍塌,刻蚀4h后其表面粗糙度由刻蚀前的3.061 μm下降至1.083 μm. 刻蚀导致表面粗糙度显著降低. 上述差别的主要原因在于金刚石膜沉积过程中掺氮导致氮缺陷在金刚石晶棱处富集, 晶棱处电子发射加强, 引导离子向晶棱运动并产生刻蚀, 从而加剧晶棱的刻蚀. 而未掺氮金刚石膜,其缺陷相对较少且分布较均匀 ,刻蚀时整体呈现为 (111) 晶面被均匀刻蚀继而晶粒坍塌的现象. 关键词： 掺氮 金刚石膜 刻蚀 非对称磁镜场     

超导纳米线单光子探测器件的制备

超导纳米线单光子探测器件(SNSPD)是超导单光子探测系统的核心器件。文中介绍了成功制备的基于5nm厚的NbN超导超薄薄膜的SNSPD器件。器件核心结构为150nm宽的纳米曲折线结构,纳米线条占空比为75%,面积为20μm×20μm。超导纳米线是利用电子束曝光(EBL)技术和反应离子刻蚀(RIE)等工艺技术制备的。所制备的SNSPD样品,在温度3.5K下的临界电流约12.9μA;在1310nm波长光波辐照,12.5μA的偏置电流下,探测效率约0.016%。     

熔石英的快速激光刻蚀

使用10.6μm连续波CO_2激光和几种工作气体,对熔石英实现了快速的激光刻蚀.得到了刻蚀速度高于200μm/s的干净、光滑的表面;并根据所提出的机理对观察到的实验结果进行了解释.     

飞秒激光用多层介质膜脉宽压缩光栅的设计

以薄膜光学的干涉理论和衍射光学的傅里叶模式理论为基础，给出了0.8μm飞秒激光器用多层介质膜脉宽压缩光栅的理论设计；设计采用H3L(HL)^9H0.5L2.4H的多层介质膜为基底，当刻蚀后表面浮雕结构的占宽比为0.35，线密度为1480线/mm，槽深为0.2μm，顶层HfO₂的剩余厚度为0.15μm时，对于Littrow角度(36.7°)和TE波模式入射的衍射光栅其-1级衍射效率达到95％以上. 关键词： 飞秒激光 脉宽压缩光栅 多层介质膜     

表面热透镜技术测量3.8μm和2.8μm激光薄膜的微弱吸收

 采用表面热透镜技术，对3.8μm和2.8μm激光辐照下镀制在Si基底上的单层ZnS，YbF₃和YBC薄膜及不同膜系的YbF₃/ ZnS多层分光膜和多层高反膜，以及镀制在CaF₂基底上的增透膜进行了吸收测量，并对3.8μm和2.8μm 激光的测量结果进行了比较分析。实验结果表明，2.8μm波长下的吸收比3.8μm的大得多，两者之间约相差一个量级，测得的多层高反膜YbF₃/ZnS薄膜在的3.8μm处的最低吸收为4.57×10^－4，测量系统的灵敏度约为10^-5。     

XUV成像系统中像传递函数研究用的Si刻蚀膜

 研制具有网格或条状图形的Si刻蚀膜靶，用于XUV系统中像传递函数的研究。在自截止腐蚀工艺制备Si平面薄膜的基础上，结合离子束刻蚀工艺，获得刻蚀深度为1.0 μm左右，网格尺寸为25 μm×25 μm，或条状线宽为5 μm的Si刻蚀膜；测量了Si刻蚀膜的形貌和刻蚀深度；研究了离子束刻蚀参数对图形形貌的影响。并介绍采用两种靶型获得的像传递函数信息。     

用20—1020 keV单能质子刻度CR-39固体核径迹探测器

用北京师范大学2×1.7MV串列加速器和400 kV高压倍加器产生的20—1020 keV单能质子束对CR-39固体核径迹探测器进行了刻度.为了保证质子的单能性和固体核径迹探测器上径迹密度不能超过10⁶/cm²的要求,对两台加速器分别采用了不同方法控制质子辐照数量.在串列加速器上采用了狭缝加转盘的方法,在高压倍加器上采用了100 ns单次高压脉冲扫描束流的方法,既保持了质子的单色性,又达到了质子注量小于10⁶/cm²的 关键词： 单能质子 固体核径迹探测器 CR-39     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.