Si基铁电Bi3.15Nd0.85Ti3O12多层薄膜的一致取向生长和性能的研究

采用脉冲激光沉积(PLD)技术,利用LSCO/CeO2/YSZ多异质缓冲层,在Si(100)基片上成功地制备了c轴一致取向的Bi3.15Nd0.85Ti3O12(BNT)铁电薄膜.利用X射线衍射(XRD)和扫描电镜(SEM)分析测定了薄膜的相结构、取向和形貌特征,考察了沉积温度和氧分压对BNT薄膜微结构、取向和形貌的影响,确定了BNT薄膜的最佳沉积条件.对在优化的条件下制备得到的BNT薄膜的C-V曲线测试得到了典型的蝴蝶形曲线,表明该薄膜具有较好的电极化反转存储特性.最后讨论了BNT薄膜铁电性能与薄膜取向的相关性.     

Au/PZT/BIT/p-Si异质结的制备与性能研究

采用脉冲激光沉积(PLD)工艺,制备了以Bi₄Ti₃O₁₂(BIT)为过渡阻挡层的Au/PZT/BIT/p-Si异质结.研究了BIT铁电层对Pb(Zr_0.52Ti_0.48)O₃(PZT)薄膜晶相结构、铁电及介电性能的影响,对Au/PZT/BIT/p-Si异质结的导电机制进行了讨论.氧气氛530℃淀积的PZT为多晶铁电薄膜,与直接淀积在Si基片上相比,加入BIT铁电层后PZT铁 关键词： 铁电薄膜 异质结构 脉冲激光沉积(PLD)     

CaCu3Ti4O12块材和薄膜的巨介电常数

用固相反应法和脉冲激光沉积(PLD)制备了CaCu₃Ti₄O₁₂块材和薄膜，获得了相对介电常数ε′（1kHz,300K)高于14000的介电特性，是目前该体系最好的结果.报道了(00l)取向高质量CaCu₃Ti₄O₁₂外延薄膜及其介电性质.C aCu₃Ti₄O₁₂相对介电常数ε′在100—300K温度范围 内 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 巨介电常数 PLD     

氧压对SrTiO3和SrNb0.2Ti0.8O3薄膜晶格参数的影响及激光感生热电电压效应

采用脉冲激光沉积技术制备了SrTiO₃和SrNb_0.2Ti_0.8O₃薄膜.X射线衍射分析表明在LaAlO₃(100)单晶平衬底上生长的SrTiO₃及SrNb_0.2Ti_0.8O₃薄膜是沿［001］取向的近外延生长.随着氧压在一定范围内逐渐增大,SrTiO₃薄膜的晶格参数减小,而SrNb_0.2Ti_0.8O₃薄膜的晶格参数先减小后增大.同时摸索出制备具有二维电子气超晶格(SrTiO₃/SrNb_0.2Ti_0.8O₃)_L的最佳氧压为1.0×10^-2Pa.另外在LaAlO₃(100)倾斜衬底上制备的SrNb_0.2Ti_0.8O₃薄膜中观察到激光感生热电电压效应. 关键词： 0.2Ti_0.8O₃薄膜')" href="#">SrNb_0.2Ti_0.8O₃薄膜 晶格参数 激光感生热电电压 脉冲激光沉积     

Ag/Bi4Ti3O12栅n沟道铁电场效应晶体管制备及存储特性

在溶胶-凝胶工艺获得高质量Bi₄Ti₃O₁₂薄膜的基础上 ，制备了Ag/Bi₄Ti₃O₁₂栅n沟道铁电场效应晶体管. 研 究了Si基Bi₄Ti₃O₁₂薄膜的生长特性及其对铁电薄膜/ 硅的界面状态和铁电场效应晶体管存储特性的影响. 研究表明，在合理的工艺条件下可以获 得具有较高c-轴择优取向的纯钙钛矿相Si基Bi₄Ti₃O₁₂ 铁电薄膜并有利于改善Bi₄Ti₃O₁₂/Si之间的界面特性; 顺时针回滞的C-V特性曲线和C-T曲线表明Ag/Bi₄Ti₃O_{12栅n沟道铁电场效应晶体管具有极化存储效应和一定的极化电荷保持能力; 器件的转移(I< sub>sd}-V_G)特性曲线显示Ag/Bi₄Ti₃O_{12栅n沟道铁电场效应晶体管具有明显的栅极化调制效应. 关键词： 铁电场效应晶体管 4}Ti₃O₁₂')" href="#">Bi₄Ti₃O₁₂ 存储 特性 溶胶-凝胶工艺     

La掺杂对Bi4Ti3O12薄膜铁电性能的影响

利用Sol-Gel法在Pt/Ti/SiO₂/Si衬底上制备出Bi₄Ti₃O₁₂和Bi_3.25La_0.75Ti₃O₁₂薄膜，研究了La掺杂对Bi₄Ti₃O₁₂薄膜的晶体结构、铁电性能和疲劳特性的影响，发现La掺杂没有改变Bi₄Ti₃O₁₂薄膜的基本晶体结构，并且提高了Bi₄Ti₃O₁₂铁电薄膜的剩余极化值和抗疲劳性能，对La掺杂改善Bi₄Ti₃O₁₂铁电薄膜性能的机理进行了讨论. 关键词： 铁电性能 4Ti₃O₁₂薄膜')" href="#">Bi₄Ti₃O₁₂薄膜 3.25La_0.75Ti₃O₁₂薄膜')" href="#">Bi_3.25La_0.75Ti₃O₁₂薄膜 sol-gel法 La掺杂     

溶胶-凝胶法制备Sr2Bi4Ti5O18薄膜及其铁电性能研究

采用溶胶-凝胶法,在氧气氛中和层层晶化的工艺条件下,成功地制备了沉积在Pt/Ti/SiO₂/Si(100)衬底上的铁电性能优良的Sr₂Bi₄Ti₅O₁₈ (SBTi)薄膜,并研究了SBTi薄膜的微结构、表面形貌、铁电性能和疲劳特性.研究表明：薄膜具有单一的层状钙钛矿结构，且为随机取向；薄膜表面光滑，无裂纹，厚度约为725nm；铁电性能测试显示较饱和、方形的电滞回线，当外电场强度为275kV/cm时 关键词： 溶胶-凝胶法 铁电薄膜 2Bi₄Ti₅O₁₈')" href="#">Sr₂Bi₄Ti₅O₁₈     

Si基Bi4Ti3O12铁电薄膜的制备与特性研究

采用sol-gel工艺, 在分层快速退火的工艺条件下成功地制备了高质量Si基Bi_{4Ti3O12铁电薄膜. 研究了Si基Bi4Ti3O12薄膜的生长行为、铁电性能、C-V特性和疲劳特性. 研究表明: Si基Bi4Ti3O12薄膜具有随退火温度升高沿c轴择优生长的趋势; 退火温度通过影响薄膜的晶粒尺寸、生长取向和薄膜中载流子的浓度来改变Si基Bi关键词： sol-gel法 铁电薄膜 4Ti3O12')" href="#">Bi4Ti3O12 C-V特性}     

Si基Bi3.25La0.75Ti3O12铁电薄膜的制备与特性研究

采用Sol-Gel工艺低温制备了Si基Bi_3.25La_0.75Ti₃O₁₂铁电薄膜.研究了退火温度对薄膜微观结构、介电特性与铁电性能的影响.500℃退火处理的Bi_3.25La_0.75Ti₃O₁₂薄膜未能充分晶化，晶粒细小且有非晶团聚，介电与铁电性能均较差.高于550℃退火处理的Bi_3.25La_{0.75 关键词： 铁电薄膜 3.25}La_0.75Ti₃O₁₂')" href="#">Bi_3.25La_0.75Ti₃O₁₂ Sol-Gel工艺     

Pb(Zr0.3Ti0.7)O3铁电薄膜激光感生电压效应

采用脉冲激光沉积(PLD)技术在LaSrAlTaO₃(LSATO),LaAlO₃(LAO)和SrTiO₃(STO)的单晶倾斜衬底上成功制备了Pb(Zr_0.3Ti_0.7)O₃(PZT)薄膜,在三种倾斜衬底上生长的PZT薄膜中都首次发现了LIV效应.对PZT/LSATO薄膜在a,c轴两种不同取向择优生长下的LIV效应做了研究,发现在薄膜c轴取向择优生长 关键词： 激光感生电压效应 铁电薄膜 薄膜生长取向 原子层热电堆     

La0.3Sr0.7TiO3模板层对Pb(Zr0.5Ti0.5)O3薄膜的铁电性能增强效应的研究

通过sol-gel法在Si (111) 基片上分别制备了LaNiO₃(LNO)底电极和LaNiO₃/La_0.3Sr_0.7TiO₃ (LNO/LSTO)底电极.然后采用sol-gel 方法，在两种衬底上分别制备了Pb (Zr_0.5Ti_0.5)O₃ (PZT)铁电薄膜.XRD分析表明，两种PZT薄膜均具有钙钛矿结构，且在LNO底电极上的PZT薄膜呈(100) 择优取向，而在LNO/LSTO底电极上的PZT薄膜呈随机取向.铁电性能测试表明，相对LNO衬底上制备的PZT薄膜，在LNO/LSTO底电极上制备的PZT薄膜的剩余极化强度得到了有效的增强，同时矫顽场也增大.介电常数和漏电流的测试表明，LNO/LSTO底电极上制备的PZT薄膜具有大的介电常数和漏电流. 关键词： PZT薄膜 铁电性 漏电流 0.3Sr_0.7TiO₃')" href="#">La_0.3Sr_0.7TiO₃     

Microstructure and electrical properties of Ba0.5Sr0.5TiO3 thin films prepared on copper foils with La2O3 buffer layers

Ba_0.5Sr_0.5TiO₃ (BST) thin films were deposited on copper foils via sol-gel method with La₂O₃ as a buffer layer. The films were processed in almost inert atmosphere so that the substrate oxidation was avoided while allowing the perovskite film phase to crystallize. The existence of a La₂O₃ buffer layer between the BST thin film and Cu foil improved the dielectric constant and reduced the leakage current density of the BST thin film. Meanwhile, the BST thin film exhibited ferroelectric character at room temperature, which was contrast to the para-electric behavior of the film without the buffer layer. Effects of La₂O₃ buffer layer on the crystallizability and microstructure of BST thin films were also investigated.     

Effect of different annealing methods on ferroelectric properties of 0.95Pb(Sc0.5Ta0.5)O3-0.05PbTiO3 thin films

0.95Pb(Sc_0.5Ta_0.5)O₃-0.05PbTiO₃ thin films were prepared on LaNiO₃/SiO₂/Si substrate by radio frequency magnetron sputtering, and the films were annealed subsequently with repeated many times by two approaches: normal one-step rapid thermal annealing and innovative two-steps rapid thermal annealing. X-ray diffraction demonstrates that all the films were preferred (1 0 0) oriented and an appropriate repeat of annealing process can enhance perovskite phase of the films. Scanning electron microscopy suggests that the films treated by two-steps rapid thermal annealing show crack-free, uniform size grains and dense microstructure. Measurement of remnant polarization and leakage current dependence of electric field confirms that the films treated by two-steps rapid thermal annealing exhibit better ferroelectric properties than the films treated by one-steps rapid thermal annealing. The results reveal that microstructure plays an important role in enhanced ferroelectric properties of the 0.95Pb(Sc_0.5Ta_0.5)O₃-0.05PbTiO₃ thin films.     

Structural and electrical properties of (Na0.85K0.15)0.5Bi0.5TiO3 thin films deposited on LaNiO3 and Pt bottom electrodes

(Na_0.85K_0.15)_0.5Bi_0.5TiO₃ thin films were deposited on LaNiO₃(LNO)/SiO₂/Si(1 0 0) and Pt/Ti/SiO₂/Si(1 0 0) substrates by metal-organic decomposition, and the effects of bottom electrodes LNO and Pt on the ferroelectric, dielectric and piezoelectric properties were investigated by ferroelectric tester, impedance analyzer and scanning probe microscopy, respectively. For the thin films deposited on LNO and Pt electrodes, the remnant polarization 2P_r are about 22.6 and 8.8 μC/cm² under 375 kV/cm, the dielectric constants 238 and 579 at 10 kHz, the dielectric losses 0.06 and 0.30 at 10 kHz, the statistic d_33eff values 95 and 81 pm/V. The improved piezoelectric properties could make (Na_1−xK_x)_0.5Bi_0.5TiO₃ thin film as a promising candidate for piezoelectric thin film devices.     

Ferroelectric properties of bilayer structured Pb(Zr0.52Ti0.48)O3/SrBi2Ta2O9 (PZT/SBT) thin films on Pt/TiO2/SiO2/Si substrates

Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films with large remanent polarization and SrBi₂Ta₂O₉ (SBT) thin films with excellent fatigue-resisting characteristic have been widely studied for non-volatile random access memories, respectively. To combine these two advantages_, bilayered Pb(Zr_0.52Ti_0.48)O₃/SrBi₂Ta₂O₉ (PZT/SBT) thin films were fabricated on Pt/TiO₂/SiO₂/Si substrates by chemical solution deposition method. X-ray diffraction patterns revealed that the diffraction peaks of PZT/SBT thin films were completely composed of PZT and SBT, and no other secondary phase was observed. The electrical properties of the bilayered structure PZT/SBT films have been investigated in comparison with pure PZT and SBT films. PZT/SBT bilayered thin films showed larger remanent polarization (2P_r) of 18.37 μC/cm² than pure SBT and less polarization fatigue up to 1 × 10⁹ switching cycles than pure PZT. These results indicated that this bilayered structure of PZT/SBT is a promising material combination for ferroelectric memory applications.     

Influence of [S2O3]/[Sm] on Sm2S3 thin films deposited by liquid phase deposition method on self-assembled monolayers

Sm₂S₃ thin films were prepared on Si (1 0 0) substrates using SmCl₃ and Na₂S₂O₃ as precursors by liquid phase deposition method on self-assembled monolayers. The influence of the molar concentration ratio of [S₂O₃²⁻]/[Sm³⁺] on the phase compositions, surface morphologies and optical properties of the as-deposited films were investigated. The as-deposited Sm₂S₃ thin films were characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), ultraviolet-visible (UV-vis) and photoluminescence spectrum (PL). Results show that it is important to control the [S₂O₃²⁻]/[Sm³⁺] during the deposition process and monophase Sm₂S₃ thin films with orientation growth along (0 1 1) direction can be achieved when [S₂O₃²⁻]/[Sm³⁺] = 2.0, pH 3.0, with citric acid as a template agent. The as-deposited thin films exhibit a dense and crystalline surface morphology. Good transmittance in the visible spectrum and excellent absorbency of ultraviolet light of the thin films are observed, and the band gap of the thin films first decrease and then increase with the increase of the [S₂O₃²⁻]/[Sm³⁺]. The as-deposited thin films also exhibit red photoluminescence properties under visible light excitation. With the increase of the [S₂O₃²⁻]/[Sm³⁺] in the deposition solution, the PL properties of Sm₂S₃ thin films are obviously improved.     

Chemical bath deposition of hausmannite Mn3O4 thin films

A low-temperature chemical bath deposition (CBD) technique has been used for the preparation of Mn₃O₄ thin films onto glass substrates. The kinetic behavior and the formation mechanism of the solid thin films from the aqueous solution have been investigated. Structure (X-ray diffraction and Raman), morphological (atom force microscope), and optical (UV-vis-NIR) characterizations of the deposited films are presented. The results indicated that the deposited Mn₃O₄ thin films of smooth surface with nanosized grains were well crystalline and the optical bandgap of the film was estimated to be 2.54 eV.