退火对Mn和N共掺杂的Zn0.88Mn0.12O:N薄膜特性的影响

以NH₃为掺N源,采用电子束反应蒸发技术生长了Mn和N共掺杂的Zn_1-xMn_xO:N薄膜,生长温度为300℃,然后在O₂气氛中400℃退火0.5 h.X射线衍射测量表明,Zn_0.88Mn_0.12O(Mn掺杂)薄膜或Zn_0.88Mn_0.12O:N(Mn和N共掺杂)薄膜仍具有单一晶相纤锌矿结构,未检测到杂质相 关键词： ZnO薄膜 Mn和N共掺杂 电学特性 磁特性     

过渡金属与F共掺杂ZnO薄膜结构及磁、光特性

采用溶胶-凝胶法在玻璃衬底上制备了过渡金属元素与F共掺杂Zn_0.98-xTM_xF_0.02O (TM_x=Cu_0.02, Ni_0.01, Mn_0.05, Fe_0.02, Co_0.05)薄膜, 进而利用X射线衍射仪、扫描电子显微镜、紫外-可见透过谱、光致发光及振动样品磁强计等研究了薄膜的表面形貌、微结构、禁带宽度及光致发光(PL)和室温磁学特性. 研究表明: 掺杂离子都以替位的方式进入了ZnO晶格, 掺杂不会破坏ZnO的纤锌矿结构. 其中Zn_0.93Co_0.05F_0.02O薄膜样品的颗粒尺寸最大, 薄膜的结晶度最好且c轴择优取向明显; Zn_0.93Mn_0.05F_0.02O薄膜样品的颗粒尺寸最小, 薄膜结晶度最差且无明显的c轴择优取; Cu, Ni, Fe与F共掺杂样品的颗粒尺寸大小几乎相同. TM掺杂样品均表现出很高的透过率, 同时掺杂后的薄膜样品的禁带宽度都有不同程度的红移. PL谱观察到Zn_0.98-xTM_xF_0.02O薄膜的发射峰主要由较强的紫外发射峰和较弱的蓝光发射峰组成. Zn_0.93Mn_0.05F_0.02O薄膜样品的紫外发光峰最弱, 蓝光发射最强, 饱和磁化强度最大; 与之相反的是Zn_0.96Cu_0.02F_0.02O薄膜, 其紫外发光峰最强, 蓝光发射最弱, 饱和磁化强度最小. 结合微结构和光学性质对Zn_0.98-xTM_xF_0.02O薄膜的磁学性质进行了讨论.     

射频辅助N掺杂ZnO薄膜的生长及其光电特性

在MOCVD设备中采用改进的射频辅助生长装置,通过裂解N2及N-Al共掺杂的方法进行ZnO的p型掺杂研究。通过二次离子质谱(SIMS)、X射线衍射(XRD)、原子力显微镜(AFM)、光致发光(PL)谱等方法分析了薄膜中N杂质的浓度,以及射频功率与晶体质量、表面形貌以及光学特性之间的关系,并与Al掺杂和N掺杂的ZnO薄膜进行对比。实验结果表明,N掺杂的浓度高达1020cm-3;N-Al共掺杂极大地增加了ZnO的成核速率,其主要原因是N离化所起的作用;N-Al共掺的ZnO薄膜显示出p型性质,而N掺杂的ZnO薄膜由于N原子处于非激活状态而呈现高阻,这说明N-Al共掺杂对ZnO中N原子的活化起到一定作用。     

高质量立方相ZnMgO的制备与紫外受激发射特性研究

利用脉冲激光沉积（PLD）设备在蓝宝石衬底上制备了高质量Zn_1-xMg_xO单晶薄膜,并对其结构和光学特性进行了深入细致的研究。通过能量衍射谱（EDS）确认Zn_1-xMg_xO薄膜的Mg组分为45%。在Zn_0.55Mg_0.45O薄膜的X射线衍射谱（XRD）中观测到了明显的位于36.67°的衍射峰,对应的是（111）晶向的立方相ZnMgO。从透射光谱中可以看出,Zn_0.55Mg_0.45O具有陡峭的吸收边,没有发生相分离,在透射电镜图谱中也得到了证实。该ZnMgO薄膜还表现出了优异的光学特性,在Zn_0.55Mg_0.45O材料体系中实现了峰位位于310 nm的紫外光泵浦受激发射,其激光发射的阈值仅为22 kW/cm²。     

用卢瑟福背散射/沟道技术研究ZnO/Zn0.9Mg0.1O/ZnO异质结的弹性应变

利用卢瑟福背散射/沟道技术对射频等离子体辅助分子束外延法生长在蓝宝石衬底上的ZnO/Zn_0.9Mg_0.1O/ZnO异质结进行了组分分析，并得到了异质结弹性应变随深度的变化，应变由界面向表面逐渐释放，并由负变正，且在ZnO与Zn_0.9Mg_0.1O界面处轻微增大.负的应变是由于ZnO与衬底的晶格失配和热失配，而逐渐变为正值是Zn_0.9Mg_0.1O与ZnO的晶格常数差异及弹性应变的 关键词： 异质结 卢瑟福背散射/沟道 弹性应变 ZnMgO     

Ag掺杂p型ZnO薄膜及其光电性能研究

采用超声喷雾热分解法在石英衬底上以醋酸锌水溶液为前驱体,以硝酸银水溶液为Ag掺杂源生长了Ag掺杂ZnO(ZnO：Ag)薄膜.研究了衬底温度对所得ZnO：Ag薄膜的晶体结构、电学和光学性质的影响规律.所得ZnO：Ag薄膜结构良好,在室温光致发光谱中检测到很强的近带边紫外发光峰,透射光谱中观测到非常陡峭的紫外吸收截止边和较高的可见光区透过率,表明薄膜具有较高的晶体质量与较好的光学特性.霍尔效应测试表明,在500℃下获得了p型导电的ZnO：Ag薄膜,载流子浓度为5.30×10¹⁵cm关键词： ZnO：Ag薄膜 p型掺杂 超声喷雾热分解 霍尔效应     

m面蓝宝石上ZnO/ZnMgO多量子阱的制备及发光特性研究

利用等离子体辅助分子束外延设备(P-MBE)在m面的蓝宝石(m-Al₂O₃)衬底上制备了ZnO/Zn_0.85Mg_0.15O多量子阱.反射式高能电子衍射谱(RHEED)图样的原位观察表明,多量子阱结构是以二维模式生长的.从光致发光谱中可以看到ZnO/Zn_0.85Mg_0.15O多量子阱在室温仍具有明显的量子限域效应.在290 K时阱宽为3 nm的ZnO/Zn_{0.85关键词： 等离子体辅助分子束外延 ZnO多量子阱 光致发光}     

带隙可调的Al，Mg掺杂ZnO薄膜的制备

利用射频磁控溅射（RF-MS）方法,固定Al₂O₃掺杂量2 wt%,Mg掺杂量分别为1 wt%,3 wt%和5 wt%,在玻璃基底上制备了Al掺杂和Al,Mg共掺杂的ZnO薄膜,在500 ℃空气中退火2 h后,测量并比较了它们的光学和电学性质．结果表明,Al,Mg共掺杂的ZnO薄膜结晶质量良好,具有ZnO纤锌矿结构,具有较强的（002）面衍射峰,表明薄膜晶体沿c轴优先生长;与Al掺杂ZnO薄膜相比蓝端光透射率增加,1 wt%和3 wt% Mg掺杂薄 关键词： 射频磁控溅射 ZnO薄膜 Al Mg共掺杂     

离子束增强沉积制备p型氧化锌薄膜及其机理研究

采用离子束增强沉积方法在Si和SiO₂/Si衬底上制备In-N共掺杂ZnO薄膜(INZO)，溅射靶是用ZnO和2 atm% In₂O₃粉体均匀混合并压制而成，在氩离子溅射ZnO靶的同时，氮、氩混合离子束垂直注入沉积的薄膜.实验结果显示INZO薄膜具有(002)的择优取向，并且为p型导电，电阻率最低为0.9Ωcm.薄膜在氮气、氧气气氛下退火，对薄膜的结构和电学特性与成膜和退火条件的关系进行了分析. 关键词： 氧化锌薄膜 p型掺杂 离子束增强沉积     

原位氧化Zn3N2制备p型ZnO薄膜的性能研究

采用射频反应溅射法在玻璃衬底上制备Zn₃N₂薄膜，然后向真空室中通入纯氧气进行热氧化制备ZnO薄膜.利用X射线衍射、扫描电子显微镜、霍尔效应测量、透射光谱和光致发光光谱等表征技术，研究了氧化温度和氧化时间对ZnO薄膜的结晶质量、电学性质和光学性能的影响.研究结果显示，450 ℃ 下氧化2 h后的样品中除含有ZnO外，还有Zn₃N₂成分，500 ℃下氧化2 h可以制备出电阻率为0.7 Ωcm，空穴载流子浓度为10^{关键词： p型ZnO薄膜 3N₂薄膜')" href="#">Zn₃N₂薄膜 射频溅射 原位氧化}     

Nanoscale structural investigation of Zn_(1-x)Mg_xO alloy films on polar and nonpolar ZnO substrates with different Mg contents

Zn_(1-x)Mg_xO alloy films are important deep ultraviolet photoelectric materials.In this work,we used plasma-assisted molecular beam epitaxy to prepare Zn_(1-x)Mg_xO films with different magnesium contents on polar(0001) and nonpolar(1010) ZnO substrates.The nanoscale structural features of the grown alloy films as well as the interfaces were investigated.It was observed that the cubic phases of the alloy films emerged when the Mg content reached 20% and 37% for the alloy films grown on the(0001) and(1010) ZnO substrates,respectively.High-resolution transmission electron microscopy images revealed cubic phases without visible hexagonal phases for the alloy films with more than 70% magnesium,and the cubic phases exhibited three-fold and two-fold rotations for the alloy films on the polar(0001) and nonpolar(1010) ZnO substrates,respectively.This work aims to provide references for monitoring the Zn_(1-x)Mg_xO film structure with respect to different substrate orientations.     

Structural and electrical properties of nitrogen and aluminum codoped p-type ZnO films

To resolve the problem of p-type doping in ZnO, nitrogen and aluminum (N-Al) codoped ZnO films were prepared by the ultrasonic spray pyrolysis (USP) technique. The structural and electrical properties of N-Al codoped ZnO films were investigated. The results demonstrate that the undoped ZnO films exhibit the preferential orientation of (002) plane, while ZnO films show high orientation of (101) plane after codoping with N and Al. The N-Al codoped ZnO films under optimum conditions show p-type conduction, with a low resistivity of 1.7×10⁻²Ω cm, carrier concentration of 5.09×10¹⁸ cm⁻³ and high Hall mobility of 73.6 cm² V⁻¹ s⁻¹. A conversion from p-type conduction to n-type was observed during the increase of measurement temperature.     

Thickness effect on the evolution of morphology and optical properties of ZnO films

N-Al co-doped ZnO films with various thicknesses were deposited on glass substrates by ultrasonic spray pyrolysis (USP). The crystalline microstructure, morphology, distribution of elements and photoluminescence properties of ZnO films were characterized by X-ray diffraction (XRD), field emission scanning microscopy (FESEM), energy dispersive X-ray spectroscopy (EDS) and photoluminescence (PL) spectroscopy. The XRD and FESEM results show that with the increase of film thickness the grain size increases and the grain shape changes from regular hexagonal sheet-like to wedge-shaped, even pyramidal. The PL spectra illustrate that there is an obvious red-shift for the emission center from ultraviolet to blue region, and the intensities of defects emissions increase with the increase of thickness. In addition, the electrical properties are proved to be strongly affected by film thickness.     

Si(100)衬底上Mg_(0.33)Zn_(0.67)O薄膜的结构及光学性能

采用射频磁控溅射法在Si(100)衬底上制备了Mg_(0.33)Zn_(0.67)O薄膜,研究了Mg_(0.33)Zn_(0.67)O薄膜的结构和光学性能。结果表明,Si(100)衬底上Mg_(0.33)Zn_(0.67)O薄膜呈六方纤锌矿结构,薄膜沿c方向取向生长,且c轴方向晶格增大0.03 nm。薄膜呈现优异的半导体特性,激子吸收峰位于297 nm,禁带宽度约为4.3 eV。薄膜平均粒径约为20 nm。薄膜在深紫外激发下的荧光发射位于368 nm。     

The influence of substrate and annealing temperatures on electrical properties of p-type ZnO films

In this study, p-type ZnO films with excellent electrical properties were prepared by ultrasonic spray pyrolysis (USP) combining with a N-Al codoping technique. The influence of the substrate temperature and annealing temperature on electrical properties of ZnO films was investigated. The growth and doping process of ZnO films was explored by thermogravimetry, differential scanning calorimetry and mass spectrum (TG-DSC-MS) measurements. It is suggested that the variation of electrical properties of ZnO films with the substrate temperature and annealing temperature results from the removal of H element out of the films.     

MOCVD法制备的p-ZnO/n-SiC 异质结器件及其电致发光性能

采用光辅助金属有机化学汽相沉积(PA-MOCVD)法在n-SiC(6H)衬底上制备出As掺杂的p型ZnO薄膜,并制备出相应的p-ZnO:As/n-SiC异质结器件。X射线衍射(XRD)和光致发光(PL)测试表明,ZnO薄膜具有较好的结构和光学特性。电流-电压(I-V)测试结果表明,该型异质结器件具有良好的整流特性,开启电压为5.0 V,反向击穿电压约为-13 V。正向偏压下,器件的电致发光(EL)谱表现出两个分别位于紫外和可见光区域的发光峰,通过和ZnO、SiC的PL谱对照,证实异质结器件的发光峰来源于ZnO侧的辐射复合。     

籽晶层对喷雾热分解法生长ZnO薄膜结晶质量和光电性能的影响

通过脉冲激光沉积(PLD)方法在Si(100)衬底上沉积一层高质量的ZnO籽晶层,在籽晶层上进一步采用超声喷雾热分解(USP)法生长ZnO薄膜,研究了籽晶层对ZnO薄膜结晶质量和ZnO/Si异质结光电特性的影响。研究结果表明,在籽晶层的诱导作用下,USP法生长ZnO薄膜由多取向结构变为(002)单一取向,结晶性能得到了显著改善;籽晶层上生长的薄膜呈现出垂直于衬底生长的柱状晶结构,微观结构更加致密。通过研究紫外光照前后ZnO/Si异质结的整流特性,发现引入籽晶层后,反向偏压下异质结的光电响应显著增加,并且在开路状态下出现明显的光伏效应。     

Structural, optical and electrical properties of Al-N codoped ZnO films by RF-assisted MOCVD method

N-doped ZnO films were produced using N₂ as N source by metal-organic chemical vapor deposition (MOCVD) system which has been improved with radio-frequency (RF)-assisted equipments. The data of secondary ion mass spectroscopy (SIMS) indicate that the concentration of N in N-doped ZnO films is around 5 × 10²⁰ cm⁻³, implying that sufficient incorporation of N into ZnO can be obtained by RF-assisted equipment. On this basis, the structural, optical and electrical properties of Al-N codoped ZnO films were studied. Then, the effect of RF power on crystal quality, surface morphologies, optical properties was analyzed using X-ray diffraction, atomic force microscopy and photo-luminescence methods. The results illustrate that the RF plasma is the key factor for the improvement of crystal quality. Then the observation of A⁰X recombination associated with N_O acceptor in low-temperature PL spectrum proved that some N atoms have occupied the positions of O atoms in ZnO films. Hall measurements shown that p-type ZnO film deposited on quartz glasses was obtained when RF power was 150 W for the Al-N codoped ZnO films, while the resistivity of N-doped ZnO films was rather high. Compared with the Al-doped ZnO film, the obviously increased resistivity of codoped films indicates that the formation of N_O acceptors compensate some donors in ZnO films effectively.     

采用PVA方法制备ZnO基发光稀磁半导体

不同的制备工艺对ZnO薄膜的微结构和性能有很大的影响,为了得到成本较低,样品具有较好特性的实验方法,对于制备手段进行了探索。使用PVA溶胶-凝胶法制备了Zn_0.88Co_0.12O薄膜,研究了不同退火工艺对其微结构的影响。对于Zn_0.88Co_0.12O样品的微结构和室温下的铁磁性和发光特性,具体比较分析了产生原因。对比了Co掺杂和复合Co、Fe掺杂Zn_0.88(Co_0.5Fe_0.5)_0.12O样品的微结构,采用振动样品磁强计(VSM)测量了样品的磁特性,发现单一掺杂的薄膜具有更好的晶体质量和更强的磁性。