4.48 nm正入射软X射线激光用Cr/C多层膜高反射镜的研制

针对4.48nm类镍钽软X射线激光及其应用实验,设计制备了工作于这一波长的近正入射多层膜高反射镜。选择Cr/C为制备4.48nm高反射多层膜的材料对,通过优化设计,确定了多层膜的周期、周期数以及两种材料的厚度比。模拟了多层膜非理想界面对高反射多层膜性能的影响。采用直流磁控溅射方法在超光滑硅基片上实现了200周期Cr/C多层膜高反射镜的制备。利用X射线衍射仪测量了多层膜结构,在德国BessyⅡ同步辐射上测量了在工作波长处多层膜反射率,测量的峰值反射率达7.5%。对衍射仪测量的掠入射反射曲线和同步辐射测量的反射率曲线分别进行拟合,得到的粗糙度和厚度比的结果相近。测试结果表明,所制备的Cr/C多层膜样品结构良好,在指定工作波长处有较高的反射峰,达到了设计要求。     

低原子序数材料窄带多层膜的研制

为研制极紫外波段窄带多层膜反射镜,采用低原子序数材料组合设计了30.4 nm波长处Mg/SiC,Si/SiC,Si/B4C和Si/C多层膜反射镜,并与极紫外波段传统的Mo/Si多层膜反射镜进行对比。采用直流磁控溅射技术制备了这些多层膜,在国家同步辐射实验室辐射与计量光束线完成了多层膜反射率测量,测量结果表明:Mg/SiC多层膜的带宽最小,为1.44 nm,且反射率最高,为44%;而Mo/Si多层膜的反射率仅为24%,带宽为3.11 nm。实验结果证明了采用低原子序数材料组成的多层膜的带宽要比常规多层膜窄,该方法可以应用于极紫外波段高分辨研究。     

激光等离子体光源软X射线反射率计

介绍了所研制的激光等离子体光源软X射线反射率计,该反射率计由激光等离子体光源、掠入射光栅单色仪、样品室、真空系统、样品台、光电探测系统和计算机控制系统组成,工作波段8～30 nm,测量样品的最大尺寸为130 mm×120 mm×120 mm(长×宽×高),可以利用这台反射率计对软X射线波段光栅、滤光片和多层膜反射镜等光学元件进行测量和评估。为检验反射率计的性能指标,利用该反射率计对本室研制的软X射线多层膜反射镜的反射率进行了测量,测量结果与理论计算结果符合较好,反射率测量重复性为±0.6%。     

真空紫外波段铝反射膜制备

为制备出在130～210nm波段具有良好光谱性能的铝反射膜,优化设计了铝反射镜中铝层和保护层氟化镁的厚度,理论确定铝层和氟化镁保护层最佳厚度分别为80nm和33nm。采用热舟蒸发工艺,在BK7基片上制备了Al反射膜样品,获得了130～210nm波长范围内反射率均大于80%的金属铝膜。研究了铝层沉积速率和紫外辐照处理对薄膜性能的影响,并考察了铝膜光谱性能的时效性。结果表明铝层沉积速率越快,制备的铝膜反射率越高;合理地存放铝膜元件,可以长时间内保持铝膜的光谱性能。适当的紫外辐照处理能进一步提高铝膜在真空紫外波段的反射率。     

一种软X射线多层膜界面粗糙度的计算方法

提出一个利用多层膜小角X射线衍射谱衍射峰积分强度计算多层膜界面粗糙度的公式。用磁控溅射技术制备Mo／Si多层膜，用波长为0．154nm的硬X射线测量样品在小掠入射角区的衍射曲线，分别用本文公式和反射率曲线拟合方法计算了样品的界面粗糙度。实验结果表明：由本文公式获得的界面粗糙度近似于拟合方法获得的界面粗糙度，它们略等于多层膜界面实际粗糙度。     

中心波长为13．9nm的正入射Mo／Si多层膜

用由铜靶激光等离子体光源等组成的反射率计对自行设计的周期厚度为7.14nm的120层Mo/Si多层膜进行极紫外(EUV)波段反射率测量。由于多层膜层数增加所引起的吸收、膜层界面之间的扩散以及镀膜过程中的膜厚控制误差或表面被氧化(污染)等原因,正入射Mo/Si多层膜在13.9nm处的反射率低于理论计算值73.2%,最后用原子力显微镜(AFM)测量其表面粗糙度为σ=0.401nm。     

基于磁控溅射和ICP刻蚀的RB-SiC表面平坦化工艺

采用射频磁控溅射技术在RB-SiC表面沉积Si平坦化层,通过正交试验研究了射频功率、Ar流量和工作气压三个因素对薄膜表面质量和形貌的影响规律,以获取最佳的薄膜沉积参数.射频功率120 W、工作气压1.2Pa和Ar流量40sccm条件下获得了最佳质量的平坦化样品,利用电感耦合等离子体对平坦化膜层进行刻蚀抛光,通过Lambda950分光光度计测试不同工艺阶段样品表面的反射率.结果表明,相比于未处理的RB-SiC初始样品,经过平坦化和等离子体刻蚀的样品表面粗糙度标准差值由1.819nm减小至0.919nm,样品表面反射率相应地提高了2%.由此说明射频磁控溅射平坦化沉积与电感耦合等离子体刻蚀的组合工艺可实现RB-SiC表面的高质量加工.     

紫外波段SiO2/Si3N4介质膜分布式布拉格反射镜的制备与研究

采用光学传递矩阵方法设计了紫外波段SiO₂/Si₃N₄介质膜分布式布拉格反射镜, 并利用等离子体增强化学气相沉积技术在蓝宝石(0001)衬底上制备了SiO₂/Si₃N₄介质膜分布式布拉格反射镜. 光反射测试表明, 样品反射谱的峰值波长仅与理论模拟谱线相差10 nm, 并随着反射镜周期数的增加而蓝移. 由于SiO₂与Si₃N₄具有相对较大的折射率比, 因而制备的周期数为13的样品反射谱的峰值反射率就已大于99%. 样品反射谱的中心波长为333 nm, 谱峰的半高宽为58 nm. 样品截面的扫描电子显微镜和表面的原子力显微镜测量结果表明, 样品反射谱的中心波长蓝移是由子层的层厚和界面粗糙度的变化引起的. X射线反射谱表明,子层界面过渡层对于反射率的影响较小, 并且SiO₂膜的质量比Si₃N₄差, 也是造成反射率低于理论值的原因之一.     

亚飞秒啁啾Mo/Si多层膜反射镜的设计、制作与性能检测

针对利用高次谐波获取亚飞秒脉冲的实验需求,设计制备了啁啾为-2 800 as2的啁啾Mo/Si多层膜反射镜.数值计算表明,采用所设计的啁啾多层膜反射镜可以获得86 as的脉冲.通过直流磁控溅射方法实现了Mo/Si多层膜样品的制备.在合肥同步辐射上进行了多层膜反射率的测量,在所设计的工作波长内,多层膜的平均反射率为5.6±2.3%.在考虑最上层Si的氧化作用后,对测量曲线进行拟合,得到的反射率曲线和膜层厚度分布分别与测试曲线和设计结果相吻合.     

可见光波段及1 064 nm波长处用于Glan-Taylor棱镜减反射膜

为了提高Glan-Taylor棱镜的透射率,研究了Glan-Taylor棱镜在可见光波段及1 064 nm波长处减反射膜膜的设计和制备.为提高薄膜和冰洲石晶体的附着力,采用沉积Al2O3为过渡层,ZrO2作缓冲层的方法,用单纯形优化的方法进行膜系优化设计.用电子束沉积和离子束辅助沉积的方法制备了多层减反射膜,并采用石英晶体振荡法监控膜厚和沉积速率.测量结果表明,在可见光波段及1 064 nm波长处的剩余反射率均小于0.5%经测试薄膜与冰洲石晶体的附着力性能良好.     

Self-organization of five species in a cyclic competition game

Cyclic competition game models, particularly the “rock–paper–scissors” model, play important roles in exploring the problem of multi-species coexistence in spatially ecological systems. We propose an extended “rock–paper–scissors” game to model cyclic interactions among five species, and find that two of the five can coexistent when biodiversity disappears, which is different from the “rock–paper–scissors” game. As the number of fingers is five, we named the new model the “fingers” game, where the thumb, forefinger, middle finger, ring finger, and little finger cyclically dominate their subsequent species and are dominated by their former species. We investigate the “fingers” model in two ways: direct simulations and nonlinear partial differential equations. An important finding is that the number of species in a cyclic competition game has an influence on the emergence of biodiversity. To be specific, the “rock–paper–scissors” model is in favor of maintaining biodiversity in comparison with the “fingers” model when the variables (population size, reproduction rate, selection rate, and migration rate) are the same. It is also shown that the mobility and reproduction rate can promote or jeopardize biodiversity.     

Contrastive analysis on tone between Putonghua and Taiwan Mandarin

The differences of the pitch and duration of Chinese syllables between Putonghua （PTH） and Taiwan Mandarin （TM） were studied. The speech materials to be used are not only isolated syllables, but also sentences. The results reveal that： For the isolated syllables, T1 and T2 in TM are influenced by Minnan dialect, therefore their pitch are lower than those in PTH. T3 is fall-rise in PTH, while it is fall in TM. Moreover, the syllable duration sequence for different tone is T3〉T2〉T1〉T4 in PTH, while it is T1〉T2〉T3〉T4 in TM. For the syllables in sentences, T2 is mid-rise in PTH, while it is mid-level in TM. And the T3 is longer than T4 but shorter than T1 or T2 in PTH, while it is the shortest in TM. Furthermore the effects of prosodic phrase boundary on duration for different tones are almost the same in PTH, but the lengthening part of T1 or T2 is longer than that of T3 or T4 in TM.     

Experimental study on downstep in Chinese intonation

Downstep in pitch contour of Chinese Putonghua is examined using subtly designed sentences by controlling tone combinations. The results show both automatic and nonautomatic downstep phenomena exist in Chinese. In non-automatic downstep, low tones compress downwards the pitch range of the following syllables. and the main influence of downstep is on topline. Low tone not only lower the topline behind it, but also raise the high tones before it, the effects are compatible with each other. In automatic downstep, the topline of pitch contour in intonational phrase is presented as a linear downtrend, but it differs among speakers due to the effect of personal stress practice. In comparison with downstep phenomenon in other tone or non-tone languages, the downstep ratio in Chinese is not constant, and the domain of downstep is not limited within the adjacent tones.     

Abelian-Higgs phase of SU(2) QCD and glueball energy

It is shown that SU(2) QCD admits an dual Abelian-Higgs phase, with a Higgs vacuum of a type-Ⅱ superconductor. This is done by using a connection decomposition for the gluon field and the random-direction approximation. Using a bag picture with soft wall, we presented a calculational procedure for the glueball energy based on the recent proof for wall-vortices [Nucl. Phys. B 741(2006)1].     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Signal generation in an isotropic medium in scanning electron acoustic microscope

Based on the research in Ref. [5][Materials Science and Engineering, 1989; A122： 57 63], an improved model of heat source is set up, the different modes of Lamb wave in an isotropic sample generated by a chopped electron beam at frequency f are obtained with integral transform and normal function expansion method, and the output signal of PZT coupled at the back surface of the sample is found out. The generation mechanism of SEAM （Scanning Electron Acoustic Microscopy） signal is discussed. It shows that the SEAM is a near field imaging technique with high spatial resolution and its best lateral spatial resolution is about 2√2α （α is the radius of the focused electron beam）. Some of experimental results of SEAM images are presented in the paper and it shows that the spatial resolution of SEAM is better than 0.5 μm and smaller than the thermal diffusion length of the sample. Therefore the character of near field imaging in SEAM is also proved experimentally.     

High efficiency filtering using two-dimensional photonic crystal coupled cavity structures

Transmission spectra of coupled cavity structures (CCSs) in two-dimensional (2D) photonic crystals (PCs) are investigated using a coupled mode theory, and an optical filter based on CCS is proposed. The performance of the filter is investigated using finite-difference time-domain (FDTD) method, and the results show that within a very short coupling distance of about 3λ, where λ is the wavelength of signal in vacuum, the incident signals with different frequencies are separated into different channels with a contrast ratio of 20 dB. The advantages of this kind of filter are small size and easily tunable operation frequencies.