MOCVD生长Si衬底上HT-AlN缓冲层低生长压力对GaN薄膜的影响

采用金属有机化学气相沉积（MOCVD）技术在Si（111）衬底上外延GaN薄膜,对高温AlN（HT-AlN）缓冲层在小范围内低生长压力（6.7~16.6 kPa）条件下对GaN薄膜特性的影响进行了研究。研究结果表明GaN外延层的表面形貌、结构和光学性质对HT-AlN缓冲层的生长压力有很强的的依赖关系。增加HT-AlN缓冲层的生长压力,GaN薄膜的光学和形貌特性均有明显改善,当HT-AlN缓冲层的生长压力为13.3 kPa时,得到无裂纹的GaN薄膜,其（002）和（102）面的X射线衍射峰值半高宽分别为735 arcsec和778 arcsec,由拉曼光谱计算得到的张应力为0.437 GPa,原子力显微镜（AFM）观测到表面粗糙度为1.57 nm。     

国产SiC衬底上利用AIN缓冲层生长高质量GaN外延薄膜

采用高温AlN作为缓冲层在国产SiC衬底上利用金属有机物化学气相外延技术生长GaN外延薄膜.通过优化AlN缓冲层的生长参数得到了高质量的GaN外延薄膜,其对称(0002)面和非对称(1012)面X射线衍射摇摆曲线的半峰宽分别达到130 arcsec和252 arcsec,这是目前报道的在国产SiC衬底上生长GaN最好的...     

磁控反应溅射AlN缓冲层对GaN基LED器件性能的影响

以直流磁控反应溅射法(RMS)在图形化蓝宝石衬底上制备的AlN薄膜作为缓冲层,采用金属有机化学气相沉积法(MOCVD)外延生长了GaN基LED。与MOCVD生长的低温GaN缓冲层相比,RMS制备的AlN缓冲层具有表面更平整、颗粒更小的形核岛,有利于促进GaN外延的横向生长,减少了形核岛合并时的界面数量和高度差异,降低了缺陷和位错产生的几率。研究结果表明,溅射AlN缓冲层取代传统低温GaN缓冲层后,外延生长的GaN材料具有更高的晶体质量,LED器件在亮度、漏电和抗静电能力等光电特性上均有明显提升。     

AlN插入层对硅衬底GaN薄膜生长的影响

利用金属有机化合物气相外延沉积技术在2inch(5.08cm)Si(111)图形衬底上生长了GaN外延薄膜,在Al组分渐变AlGaN缓冲层与GaN成核层之间引入了AlN插入层,研究了AlN插入层对GaN薄膜生长的影响。结果表明,随着AlN插入层厚度的增加,GaN外延膜(002)面与(102)面X射线衍射摇摆曲线半峰全宽明显变小,晶体质量变好,同时外延膜在放置过程中所产生的裂纹密度逐渐减小直至不产生裂纹。原因在于AlN插入层的厚度对GaN成核层的生长模式有明显影响,较厚的AlN插入层使GaN成核层倾向于岛状生长,造成后续生长的nGaN外延膜具有更多的侧向外延成分,从而降低了GaN外延膜中的位错密度,减少了GaN外延膜中的残余张应力。同时还提出了一种利用荧光显微镜观察黄带发光形貌来表征GaN成核层形貌和生长模式的新方法。     

金属有机物化学气相沉积同质外延GaN薄膜表面形貌的改善

为了获得高质量的GaN薄膜材料,研究了金属有机物气相沉积系统中GaN插入层对GaN衬底同质外延层表面宏观缺陷和晶体质量的影响.研究发现,插入层生长温度是影响GaN同质外延膜表面形貌和晶体质量的关键因素.由于生长模式与插入层生长温度相关,随着插入层生长温度的降低,外延膜生长模式由准台阶流模式转变为层状模式,GaN同质外延膜表面丘壑状宏观缺陷逐渐减少,但微观位错密度逐渐增大.通过对插入层温度和厚度的优化,进一步调控外延层的生长模式,最终有效降低了外延层表面的宏观缺陷,获得了表面原子级光滑平整、位错密度极低的GaN同质外延膜,其X射线衍射摇摆曲线(002),(102)晶面半峰宽分别为125arcsec和85arcsec,表面粗糙度均方根大小为0.23nm.     

GaN缓冲层对直流反应磁控溅射AlN薄膜的影响(英文)

通过直流磁控反应溅射制备了氮化铝(AlN)薄膜,研究了沉积条件与氮化镓(GaN)缓冲层对薄膜质量的影响。利用X-射线衍射仪(XRD)和扫描电镜(SEM)表征了AlN薄膜的晶体结构和表面形貌。XRD研究结果表明,低工作压强、短靶距和适当的氮气偏压有利于(002)择优取向的AlN薄膜沉积。随着沉积时间的增加,沉积在50 nm厚的GaN缓冲层上的AlN薄膜的(002)面的衍射峰的半高宽急剧减小,而沉积在1μm厚的GaN薄膜上的AlN薄膜的(002)面的衍射峰的半高宽几乎不变。SEM测试结果表明:在沉积的初期,沉积在1μm厚的GaN薄膜上的AlN薄膜的(002)面的晶粒大小分布比沉积在50 nm厚的GaN缓冲层上的AlN薄膜的均匀,而随着沉积时间的增加,它们的晶粒大小分布几乎趋向一致。     

高温AlN插入层对AlGaN/GaN异质结材料和HEMTs器件电学特性的影响

研究了在GaN缓冲层中插入40 nm厚高温AlN层的GaN外延层和AlGaN/GaN异质结材料, AlN插入层可以增加GaN层的面内压应力并提高AlGaN/GaN高电子迁移率晶体管（HEMTs）的电学特性. 在精确测量布拉格衍射角的基础上定量计算了压应力的大小. 增加的压应力一方面通过增强GaN层的压电极化电场, 提高了AlGaN/GaN异质结二维电子气（2DEG）面密度, 另一方面使AlGaN势垒层对2DEG面密度产生的两方面影响相互抵消. 同时, 这种AlN插入层的采用降低了GaN与AlGaN层之间的 关键词： 高温AlN插入层 AlGaN/GaN异质结 二维电子气 应力     

氮化铝单晶薄膜的ECR PEMOCVD低温生长研究

采用电子回旋共振等离子体增强金属有机物化学气相沉积（ECR－PEMOCVD）技术，在c轴取向的蓝宝石即α Al2O3（0001）衬底上，以氮化镓（GaN）缓冲层和外延层作为初始层，分别以高纯氮气（N2）和三甲基铝(TMAl)为氮源和铝源低温生长氮化铝（AlN）薄膜.并利用反射高能电子衍射（RHEED）、原子力显微镜（AFM）和x射线衍射（XRD）等测量结果，研究了氢等离子体清洗、氮化和GaN初始层对六方AlN外延层质量的影响，从而获得解理性与α Al2O3衬底一致的六方相AlN单晶薄膜，其XRD半高宽为1 关键词： AlN 氢等离子体清洗 氮化 GaN     

SiO2对多层GaN外延片热应力分布影响的仿真分析

为了研究SiO2对多层结构GaN外延片的热应力的影响,以直径d为40 mm的GaN外延片为研究对象,利用有限元分析法分别对蓝宝石/AlN/GaN和蓝宝石/SiO2/AlN/GaN这两种光阴极组件外延片表面热应力进行理论计算和仿真。在其他结构参数相同的情况下,分别分析了两种光阴极组件外延片径向和厚度方向的应力分布,分析了外延片热应力分布及影响因素。分析结果显示:在1 200 ℃的生长温度下,径向区域内的热应力分布比较均匀,厚度方向的热应力均在衬底和外延层的界面上发生突变。最后分析了外延片生长温度、蓝宝石衬底和GaN、AlN过渡层厚度对表面热应力的影响。     

H2载气流量对AlN缓冲层生长的影响

在Si(111)衬底上用金属有机化学气相沉积(MOCVD)设备生长了AlN和GaN薄膜。采用高分辨X射线衍射、椭圆偏振光谱仪和原子力显微镜研究了AlN缓冲层生长时的载气(H2)流量变化对GaN外延层的影响。椭圆偏振仪测试表明:相同生长时间内AlN的厚度随着H2流量的增加而增加,即H2流量增加会导致AlN生长速率的提高。原子力显微镜测试表明:随着H2流量的增加,AlN表面粗糙度也呈上升趋势。XRD测试表明:随着AlN生长时的H2流量的增加,GaN的(0002)和(1012)峰值半宽增大,即螺型穿透位错密度和刃型穿透位错密度增加。可能是由于AlN缓冲层的表面形貌较差,导致GaN的晶体质量有所下降。实验结果表明:采用较低的H2流量生长AlN缓冲层可以控制AlN的生长速率,在一定程度上有助于提高GaN的晶体质量。     

Influence of AlN Buffer Thickness on GaN Grown on Si(111) by Gas Source Molecular Beam Epitaxy with Ammonia

Hexagonal GaN is grown on a Si(111) substrate with AlN as a buffer layer by gas source molecular beam epitaxy (GSMBE) with ammonia. The thickness of AlN buffer is changed from 9 to 72nm. When the thickness of AlN buffer is 36nm, the surface morphology and crystal quality of GaN is optimal. The in-situ reflection high energy electron diffraction (RHEED) reveals that the transition to a two-dimensional growth mode of AlN is the key to the quality of GaN. However, the thickness of AlN buffer is not so critical to the residual in-plane tensile stress in GaN grown on Si(111) by GSMBE for AlN thickness between 9 to 72nm.     

The influence of AlN/GaN superlattice intermediate layer on the properties of GaN grown on Si（111） substrates

AlN/GaN superlattice buffer is inserted between GaN epitaxial layer and Si substrate before epitaxial growth of GaN layer. High-quality and crack-free GaN epitaxial layers can be obtained by inserting AlN/GaN superlattice buffer layer. The influence of AlN/GaN superlattice buffer layer on the properties of GaN films are investigated in this paper. One of the important roles of the superlattice is to release tensile strain between Si substrate and epilayer. Raman spectra show a substantial decrease of in-plane tensile strain in GaN layers by using AlN/GaN superlattice buffer layer. Moreover, TEM cross-sectional images show that the densities of both screw and edge dislocations are significantly reduced. The GaN films grown on Si with the superlattice buffer also have better surface morphology and optical properties.     

Effect of nitrogen gas flow and growth temperature on extension of GaN layer on Si

The effect of nitrogen flow and growth temperature on extension of GaN on Si substrate has been studied. By increasing the nitrogen flow whose outlet is located in the center of the MOCVD (metal-organic chemical vapor deposition) gas/particle screening flange and by increasing the growth temperature of HT-AlN and AlGaN buffer layers near the primary flat of the wafer, the GaN layer has extended more adequately on Si substrate. In the meantime, the surface morphology has been greatly improved. Both the AlN and GaN crystal quality uniformity has been improved. X-ray diffraction results showed that the GaN (0002) XRD FWHMs (full width at half maximum) decreased from 579 arcsec～ 1655 arcsec to around 420 arcsec.     

Nonpolar a-plane GaN grown on r-plane sapphire using multilayer AlN buffer by metalorganic chemical vapor deposition

Mirror-like and pit-free non-polar a-plane (1 1 −2 0) GaN films are grown on r-plane (1 −1 0 2) sapphire substrates using metalorganic chemical vapor deposition (MOCVD) with multilayer high-low-high temperature AlN buffer layers. The buffer layer structure and film quality are essential to the growth of a flat, crack-free and pit-free a-plane GaN film. The multilayer AlN buffer structure includes a thin low-temperature-deposited AlN (LT-AlN) layer inserted into the high-temperature-deposited AlN (HT-AlN) layer. The results demonstrate that the multilayer AlN buffer structure can improve the surface morphology of the upper a-plane GaN film. The grown multilayer AlN buffer structure reduced the tensile stress on the AlN buffer layers and increased the compressive stress on the a-plane GaN film. The multilayer AlN buffer structure markedly improves the surface morphology of the a-plane GaN film, as revealed by scanning electron microscopy. The effects of various growth V/III ratios was investigated to obtain a-plane GaN films with better surface morphology. The mean roughness of the surface was 1.02 nm, as revealed by atomic force microscopy. Accordingly, the multilayer AlN buffer structure improves the surface morphology and facilitates the complete coalescence of the a-plane GaN layer.     

Influence of AlN buffer layer thickness on structural properties of GaN epilayer grown on Si (111) substrate with AlGaN interlayer

We present the growth of GaN epilayer on Si (111) substrate with a single AlGaN interlayer sandwiched between the GaN epilayer and AlN buffer layer by using the metalorganic chemical vapour deposition. The influence of the AlN buffer layer thickness on structural properties of the GaN epilayer has been investigated by scanning electron microscopy, atomic force microscopy, optical microscopy and high-resolution x-ray diffraction. It is found that an AlN buffer layer with the appropriate thickness plays an important role in increasing compressive strain and improving crystal quality during the growth of AlGaN interlayer, which can introduce a more compressive strain into the subsequent grown GaN layer, and reduce the crack density and threading dislocation density in GaN film.     

High resolution X-ray diffraction of GaN grown on Si (1 1 1) by MOVPE

High temperature GaN layers have been grown on Si (1 1 1) substrate by metalorganic vapor phase epitaxy (MOVPE). AlN was used as a buffer layer and studied as a function of thickness and growth temperature. The growth was monitored by in situ laser reflectometry. High resolution X-ray diffraction (HRXRD) revealed that optimized monocrystalline GaN was obtained for a 40 nm AlN grown at 1080 °C. This is in good agreement with the results of morphological study by scanning electron microscopy (SEM) and also confirmed by atomic force microscopy (AFM) observations. The best morphology of AlN with columnar structure and lower rms surface roughness is greatly advantageous to the coalescence of the GaN epilayer. Symmetric and asymmetric GaN reflections were combined for twist and stress measurements in monocrystalline GaN. It was found that mosaicity and biaxial tensile stress are still high in 1.7 μm GaN. Curvature radius measurement was also done and correlated to the cracks observations over the GaN surface.     

The influence of SixNy interlayer on GaN film grown on Si(111) substrate

A method to drastically reduce dislocation density in a GaN film grown on an Si(111) substrate is newly developed. In this method, the Si_xN_y interlayer which is deposited on an AlN buffer layer in situ is introduced to grow the GaN film laterally. The crack-free GaN film with thickness over 1.7 micron is grown on an Si(111) substrate successfully. Synthesized GaN epilayer is characterized by X-ray diffraction (XRD), atomic force microscope (AFM), and Raman spectrum. The test results show that the GaN crystal reveals a wurtzite structure with the <0001> crystal orientation and the full width at half maximum of the X-ray diffraction curve in the (0002) plane is as low as 403 arcsec for the GaN film grown on the Si substrate with an Si_xN_y interlayer. In addition, Raman scattering is used to study the stress in the sample. The results indicate that the Si_xN_y interlayer can more effectively accommodate the strain energy. So the dislocation density can be reduced drastically, and the crystal quality of GaN film can be greatly improved by introducing Si_xN_y interlayer.     

Engineering of nearly strain-free ZnO films on Si(1 1 1) by tuning AlN buffer thickness

ZnO properties were investigated as a function of AlN buffer layer thickness (0–100 nm) in ZnO/AlN/Si(1 1 1) structures grown by metal organic vapor phase epitaxy. A significant improvement of ZnO film crystallinity by tuning AlN buffer thickness was confirmed by x-ray diffraction, topography and photoluminescence measurements. An optimal AlN buffer layer thickness of 50 nm is defined, which allows for growth of nearly strain-free ZnO films. The presence of free excitons at 10 K suggests high crystal quality for all ZnO samples grown on AlN/Si(1 1 1) templates. The intensities of neutral and ionized donor bound exciton lines are found to correlate with the in-plane and out-of-plane strain in the films, respectively.