CdS/CdTe薄膜太阳电池的深能级瞬态谱和光致发光研究

用深能级瞬态谱和光致发光研究了无背接触层的CdS/CdTe薄膜太阳电池的杂质分布和深能级中心.得到了净掺杂浓度在器件中的分布.确定了两个能级位置分别在E_V+0365 eV和E_V+0282 eV的深中心,它们的浓度分别为167×10¹² cm^-3和386×10¹¹ cm^-2,俘获截面分别为143×10^-14cm²和153×10^-16cm².它们来源于以化学杂质形式存在的Au和（或）Te_Cd^-复合体,或与氩氧气氛下沉积CdTe时的氧原子相关. 关键词： 深能级瞬态谱 光致发光 CdS/CdTe太阳电池     

CdTe太阳电池中起因于Cu的深能级

在CdTe太阳电池中,易引入并形成Cu深能级中心. 本文采用深能级瞬态谱测试法研究了ZnTe背接触和石墨背接触CdTe太阳电池的部分深能级中心. 研究中运用密度泛函相关理论,分析闪锌矿结构CdTe,Cd空位体系和掺Cu体系的电子态密度,计算得出T_d场和C_3v场下Cu²⁺ d轨道的分裂情况. 计算结果表明,CdTe太阳电池中的E_v+0206 eV和E_v+0122 eV两个深中心来源于Cu替代Cd原子. 计算结果还表明,掺入Cu可降低CdTe体系能量.     

ZnO/p-Si异质结的深能级及其对发光的影响

利用深能级瞬态谱(DLTS)和光致发光谱(PL),研究了ZnO/pSi异质结的两种不同温度(850℃,1000℃)退火下的深能级中心。发现850℃退火的样品存在3个明显的深中心,分别为E₁=E_v+0.21eV,E₂=E_v+0.44eV,E₃=E_v+071eV;而1000℃退火样品仅存在一个E₁=E_v+021eV的中心,且其隙态密度要比850℃退火的大。同时,测量了两个样品的PL谱。发现1000℃退火可消除一些影响发光强度的深能级,对改善晶格结构,提高样品的发光强度有利。     

在C70固体/p-GaAs结构中的甚深深能级

发展了恒温电容瞬态数据处理方法，称新方法为恒温电容瞬态时间积谱(ICTTS).用ICT TS方法测量分析了C₇₀固体/p GaAs异质结的深能级，结果发现在C₇₀固体中存在两个很深的空穴陷阱，H C₁和H₂，它们的能级位置分别为Ev⁺⁰856eV和 Ev+1037eV. 关键词： 70')" href="#">C₇₀ 深能级 恒温电容瞬态     

不同温度下制备的CdTe薄膜对太阳电池光电性能的影响

在不同温度下用近空间升华法（CSS）制备了CdTe多晶薄膜,结合I-V,C-V特性及深能级瞬态谱研究了不同温度制备的CdTe薄膜对CdS/CdTe太阳电池性能的影响.结果表明,制备温度对电池组件的开路电压影响不大,对短路电流和填充因子有影响,CdTe薄膜的深中心对温度和频率的响应基本一致.580℃制备的样品暗饱和电流密度最小,载流子浓度较高,光电特性较好,而且空穴陷阱浓度较低,深中心复合作用较小.在此研究基础上制备出了面积为300 mm×400 mm 关键词： 制备温度 CdTe薄膜 深能级瞬态谱（DLTS） CdS/CdTe太阳电池     

CdTe太阳电池的不同背电极和背接触层的特性研究

用Ni替代Au来作为CdTe太阳电池的背电极，比较了Ni,Ni/Au,Au/Ni及Au背电极对电池性能的影响.发现Ni作为背电极和ZnTe/ZnTe:Cu复合层接触，电池的开路电压V_oc略有降低，填充因子FF有增有减，变化幅度不大，但因短路电流I_sc有较大的提高，转换效率η平均增长4％.测试了不同背电极的CdTe太阳电池的暗I-V和C-V特性，对背电极剥离后的样品进行了XPS测试分析.结果表明，Ni扩散到ZnTe/ZnTe:Cu复合层的深度比Au多，且大多呈离子态，与ZnTe/ZnTe:Cu复合层中的富Te离子形成Ni_xTe，提高了掺杂浓度，使电池性能获得改善. 关键词： 金属背电极 复合背接触层 转换效率 CdTe太阳电池     

Y掺杂SrTiO3晶体材料的电子结构计算

采用基于第一性原理的密度泛函理论平面波超软赝势法, 研究了Y掺杂SrTiO₃体系的空间结构和电子结构性质, 得到了优化后体系的结构参数, 掺杂形成能, 能带结构和电子态密度. 对比掺杂浓度为0125, 025, 033时,Sr_1-xY_xTiO₃和SrTi_1-xY_xO₃的掺杂形成能,发现Y替代Sr能形成更稳定的结构. 对Sr_1-xY_xTiO₃（x=0, 0125, 025, 033） 的结构进行了优化,结果表明Y替代Sr后, 随着掺杂浓度增大, 体系的晶格常数逐渐减小, 稳定性逐渐增强. 对不同掺杂浓度的Sr_1-xY_xTiO₃能带结构的计算结果表明：纯净的SrTiO₃是绝缘体, 价带顶在R点, 导带底在Γ点, 费米能级处于价带顶; 掺杂Y后, 费米能级进入到导带底中, 体系呈金属性;掺杂浓度越大,费米能级进入导带的位置越深,禁带宽度也近似变宽. 关键词： 3')" href="#">SrTiO₃ 电子结构 掺杂 VASP     

CdTe薄膜太阳电池背接触的研究

用近空间升华法制备了CdTe多晶薄膜，用硝酸-磷酸(NP)混合液对薄膜表面进行了腐蚀.经SEM观测，腐蚀后的CdTe薄膜晶界变宽，XRD测试发现，经NP腐蚀后，在CdTe薄膜表面生成了一层高电导的富Te层.在腐蚀后的CdTe薄膜上分别制备了Cu，Cu/ZnTe：Cu，ZnTe：Cu，ZnTe/ZnTe：Cu四种背接触层，比较了它们对太阳电池性能的影响.结果表明，用ZnTe/ZnTe：Cu复合层作为背接触层的效果较好，获得了面积为0.5cm²，转换效率为13.38%的CdTe多晶薄膜太 关键词： 硝磷酸腐蚀 背接触层 CdTe太阳电池     

分子束外延生长的n型Al掺杂ZnS1-xTex深中心研究

应用电容-电压、光致荧光和深能级瞬态谱技术研究了分子束外延生长的n型Al掺杂ZnS_1-xTe_x外延层深中心.Al掺杂ZnS_0.977Te_0.023的光致荧光强度明显低于不掺杂的ZnS_0.977Te_0.023，这表明一部分Al原子形成非辐射深中心.Al掺杂ZnS_1-xTe_x(x=0，0.017，0.04和0.046)的深能级瞬态傅里叶 关键词：     

深能级对AlGaInP/GaAs异质结双极晶体管性能的影响

用深能级瞬态光谱和光致发光(PL)方法研究了AlGaInP/GaAs异质结双极晶体管(HBT)发射区AlGaInP中的深能级.得到了两个深能级,分别为E_c-E_t1＝0.42eV和E_c-E_t2＝0.59eV,其复合截面为σ_n1＝6.27×10^-17cm²和σ_n2＝6.49×10^-20cm². 关键词：     

Deep level transient spectroscopy investigation of deep levels in CdS/CdTe thin film solar cells with Te:Cu back contact

Deep levels in Cds/CdTe thin film solar cells have a potent influence on the electrical property of these devices. As an essential layer in the solar cell device structure, back contact is believed to induce some deep defects in the CdTe thin film. With the help of deep level transient spectroscopy (DLTS), we study the deep levels in CdS/CdTe thin film solar cells with Te:Cu back contact. One hole trap and one electron trap are observed. The hole trap H1, localized at E_v+0.128~eV, originates from the vacancy of Cd (V_Cd. The electron trap E1, found at E_c-0.178~eV, is considered to be correlated with the interstitial Cu_i⁼ in CdTe.     

Understanding the junction degradation mechanism in CdS/CdTe solar cells using a Cd-deficient CdTe layer

It is known that CdTe solar cells are often degraded under solar illumination. But the degradation mechanism is not fully proved because it does not appear consistently. The junction degradation in CdS/CdTe solar cells was investigated using a CdTe layer with Cd deficient composition, where Cd vacancy concentration is high. It was found that the Cu atoms easily filled the Cd vacancies in CdTe and transport to junction area from Cu back contact. PL measurement and spectral quantum efficiency measurement showed that the incorporation of Cu atoms in CdS forms a defect energy level at 1.55 eV below the conduction band in CdS. As a result, the junction built-in potential is decreased and light penetration into CdTe absorber is shielded. For reliable and stable CdTe cells, the formation of Cd vacancy in CdTe should be avoided by careful control of CdTe.     

基于氧化镍背接触缓冲层碲化镉薄膜太阳电池的研究

采用电子束蒸发法制备了NiO薄膜,并对其作为碲化镉薄膜太阳电池背接触缓冲层材料进行了相关研究.NiO缓冲层的加入使得碲化镉太阳电池开路电压显著增大.通过X射线光电子能谱测试得到的NiO/CdTe界面能带图表明NiO和CdTe的能带匹配度很好.NiO是宽禁带P型半导体材料,在电池背接触处形成背场,减少了电子在背表面处的复合,从而提高电池开路电压.通过优化NiO薄膜厚度,制备得到转换效率为12.2%、开路电压为789 mV的碲化镉太阳电池.研究证实NiO是用来制备高转换效率、高稳定性碲化镉薄膜太阳电池的一种极有前景的缓冲层材料.     

ZnSe晶体中Cu杂质深能级的ODLTS谱

用控制Cu杂质在ZnSe品格中占据位置的方法,成功地得到了Cu-G和Cu-R中心分别占优势的ZnSe:Cu晶体.首次用ODLTS方法测得与Cu-R和Cu-G中心相应的受主能级分别位于价带顶上0.72eV和0.30eV.     

Short-circuit current improvement in CdTe solar cells by combining a ZnO buffer layer and a solution back contact

Conventional CdTe solar cells have a CdS window layer, in which an absorption loss of photons with more than 2.4 eV occurs through the CdS layer. A thinner CdS layer was applied to enhance light transmission and a ZnO buffer layer with a band gap of 3.3 eV was introduced to suppress shunting through the thinner CdS window layer. A 100-nm thick ZnO layer sputter-deposited at 300 °C had uniform coverage on a transparent conductive oxide (TCO) after a subsequent high-temperature process. The ZnO layer was effective in preventing shunting through the CdS window layer so that the open-circuit voltage and fill factor of the CdTe solar cells were recovered and the short-circuit current was enhanced over that of the conventional CdTe solar cell. In the ZnO/CdS/CdTe configuration, the short-circuit current was further improved throughout the visible wavelength region by replacing the Cu-metal contact with a Cu solution contact. As a result the short-circuit current from 21.7 to 26.1 mA/cm² and the conversion efficiency of the CdTe solar cell increased from 12 to 15% without antireflective coating. Our result indicates that the Cu solution back contact is a critical factor for achieving a higher cell efficiency in addition to ZnO buffer layer.     

用光电子能谱研究CdTe太阳电池的背接触特性

CdTe太阳电池的背电极须采用高功函数金属。通过采用光电子能谱(XPS)分析了高功函数金属Au和Ni分别作为背电极的CdTe太阳电池背接触特性,发现在背电极剥离后,Au在ZnTe/ZnTe∶Cu背接触层表面以Au单质形式存在,扩散深度较浅;Ni扩散到ZnTe/ZnTe∶Cu复合层的深度比Au大,且大多呈离子态,与ZnTe/ZnTe∶Cu复合层中的富Te离子形成Ni_xTe,提高了掺杂浓度,使电池性能获得改善。在两样品中还发现,不论是Te的峰还是Zn的峰,其峰的位移变化都很小,说明两样品中Te和Zn的存在形式没有发生变化。     

Performance improvement in CdTe solar cells by modifying the CdS/CdTe interface with a Cd treatment

The performance of n-CdS/p-CdTe solar cells is often degraded under light soaking or thermal stress, even though the technology of CdTe solar cells is close to a commercial level. The Cu diffusion from a Cu back contact to a CdS window layer might degrade the cell's performance. To prevent the Cu diffusion, a very-thin intrinsic CdTe layer was introduced at the n-CdS/p-CdTe interface by depositing a very-thin Cd metal layer on the CdS film and converting the Cd metal into intrinsic CdTe during p-CdTe deposition at high temperature. By the Cd treatment on CdS surface, pinholes or voids were eliminated at the CdS/CdTe and the intermixing of Te and S at the interface was much suppressed. The depletion width was much increased and the intensity of LTPL peak was increased. The analysis suggested that an intrinsic CdTe interlayer was formed and the surface recombination rate was suppressed by the intrinsic interlayer. As a result, the short circuit current of the CdTe solar cell was significantly increased due the increased current gain in the blue wavelength region. The thermal stability of the CdTe solar cell was also greatly improved and the Cu diffusion was retarded by the intrinsic CdTe interlayer at the n-CdS/p-CdTe.     

肖特基势垒对CdS/CdTe薄膜电池J-V暗性能的影响

采用数学模拟方法分析了不同背接触势垒高度(φ_b) 对于CdS/CdTe薄膜电池的J-V(电流密度-电压)方程的影响, 得出了势垒高度与roll-over的变化对应关系. 采用相应Cu/Mo背电极的CdS/CdTe薄膜电池在220-300 K的变温J-V曲线的数值分析与理论分析相对照, 分析了背势垒对于J-V曲线拟合参数的影响. 修正了φ_b 与反向饱和电流(J_b0)关系式, 理论与实验符合得非常好. 关键词： CdS/CdTe薄膜 伏安特性 肖特基势垒 roll-over     

Development of ZnTe film with high copper doping efficiency for solar cells

Since a hole barrier was formed in back contact due to mismatch of work function, the back contact material for CdTe cell has been a significant research direction. The ZnTe:Cu is an ideal back contact material, which reduces the valence band discontinuity and can be used as the electron back reflection layer to inhibit interface recombination. The conductivity of ZnTe:Cu film is improved by applying RF-coupled DC sputtering and post-deposition heat treatment. The doping efficiency is computed as the ratio of free hole density and copper concentration, which can be correlated with performance for CdTe-based solar cell. The higher doping efficiency means that more copper atoms substitute for Zn sites in ZnTe lattices and less mobilized copper atoms remain which can enter into the CdTe absorber layer. Copper atoms are suspected as dominant element for CdTe-based cell degradation. After optimizing the ZnTe:Cu films, a systematic study is carried out to incorporate ZnTe:Cu film into CdTe solar cell. The EQE spectrum is kept relatively stable over the long wavelength range without decreasing. It is proved that the conduction band barrier of device with ZnTe:Cu/Au contact material has an effect on the EQE response, which works as free electron barrier and reduces the recombination rate of free carrier. According to the dark J—V data or the light J—V data in the linear region, the current indicates that the intercept gives the diode reverse saturation current. The results of ideality factor indicate that the dominant recombination occurs in the space charge region. In addition, the space charge density and depletion width of solar cell can be estimated by C—V profiling.     

Electrical properties of the CdTe back contact: A new chemically etching process based on nitric acid/acetic acid mixtures

The performance of the back contact is one of the major issues of CdTe solar cell research. Standard nitric-phosphoric (NP) acid chemical etching before metallization is widely used to improve contact formation. However, previous studies of this traditional etching method indicated a blocking Schottky barrier at the back contact, and a roll-over phenomenon was found in the J-V curves of the CdTe solar cells. In this work, a new etching solution, i.e. a nitric-acetic (NA) acid was employed. The etching rate was slow and a Te-rich layer was formed on the surface, which was less than 1 nm. The CdTe solar cell with this new etching method showed no roll-over phenomenon and displayed a good ohmic back contact performance. XPS analysis demonstrated that the back contact barrier height was close to those of CdTe with standard NP etching. A possible mechanism was presented for the improvement of back contact properties.