CdS/CdTe薄膜太阳电池的深能级瞬态谱和光致发光研究

用深能级瞬态谱和光致发光研究了无背接触层的CdS/CdTe薄膜太阳电池的杂质分布和深能级中心.得到了净掺杂浓度在器件中的分布.确定了两个能级位置分别在E_V+0365 eV和E_V+0282 eV的深中心,它们的浓度分别为167×10¹² cm^-3和386×10¹¹ cm^-2,俘获截面分别为143×10^-14cm²和153×10^-16cm².它们来源于以化学杂质形式存在的Au和（或）Te_Cd^-复合体,或与氩氧气氛下沉积CdTe时的氧原子相关. 关键词： 深能级瞬态谱 光致发光 CdS/CdTe太阳电池     

CdTe太阳电池中起因于Cu的深能级

在CdTe太阳电池中,易引入并形成Cu深能级中心. 本文采用深能级瞬态谱测试法研究了ZnTe背接触和石墨背接触CdTe太阳电池的部分深能级中心. 研究中运用密度泛函相关理论,分析闪锌矿结构CdTe,Cd空位体系和掺Cu体系的电子态密度,计算得出T_d场和C_3v场下Cu²⁺ d轨道的分裂情况. 计算结果表明,CdTe太阳电池中的E_v+0206 eV和E_v+0122 eV两个深中心来源于Cu替代Cd原子. 计算结果还表明,掺入Cu可降低CdTe体系能量. 关键词： 深能级瞬态谱 第一性原理 CdTe Cu杂质     

化学水浴法制备大面积CdS薄膜及其光伏应用

采用化学水浴法制备了大面积CdS多晶薄膜,研究了薄膜的形貌、结构和光学性质,结果表明,大面积CdS多晶薄膜具有良好的均匀性,通过优化CdS多晶薄膜,制成了不同CdS窗口层厚度的CdTe小面积太阳电池,减薄CdS薄膜可有效提高器件的短路电流,改善器件性能.随后,在面积30cm×40cm的衬底上制备了全面积为993.6cm²的CdTe太阳电池组件,其27个集成单元的电学性质较为均匀,太阳电池组件的光电转换效率8.13%. 关键词： 化学水浴法(CBD) CdS薄膜 CdTe太阳电池 CdTe太阳电池组件     

ZnS/CdS复合窗口层对CdTe太阳能电池短波光谱响应的影响

采用磁控溅射法制备了ZnS/CdS复合窗口层,并将其应用于CdTe太阳能电池。对所制备薄膜的形貌和结构等进行了研究。测试了具有不同窗口层的CdTe太阳电池的量子效率和光Ⅰ-Ⅴ特性,分析了ZnS薄膜制备条件对CdTe电池器件性能影响;研究了CdS薄膜厚度和ZnS/CdS复合窗口层对短波区透过率以及CdTe太阳电池的光谱响应的影响。着重研究了具有ZnS/CdS复合窗口层的CdTe太阳电池的短波光谱响应。结果表明,CdS窗口层厚度从100 nm减至50 nm后,其对短波区光子透过率平均提高了18.3%,CdTe太阳电池短波区光谱响应平均提高了27.6%。衬底温度250 ℃条件下制备的ZnS晶粒尺寸小于室温下制备的ZnS。具有ZnS/CdS复合窗口层的CdTe电池中,采用衬底温度250 ℃沉积ZnS薄膜来制备窗口层的电池器件,其性能要优于室温下沉积ZnS制备窗口层的电池器件。这说明晶粒尺寸的大小对电子输运有一定影响。在相同厚度CdS的前提下,具有ZnS/CdS复合窗口层的CdTe电池比具有CdS窗口层在短波的光谱响应提高了约2%。这说明ZnS/CdS复合窗口层能够做到减少对短波光子的吸收,从而使更多的光子被CdTe电池的吸收层吸收。     

近空间升华法制备CdS多晶薄膜的研究

系统地研究了近空间升华法(CSS)制备CdS薄膜沉积速率的影响因素。发现CdS薄膜的沉积速率随升华源温度的升高而增大,但随衬底温度和沉积气压的上升而下降。对所制备样品的结构、表面形貌和光谱透过率特性进行了测试,结果表明：(1)不同氧分压下沉积的CdS薄膜沿(103)晶向择优生长。CdCl₂氛围下退火后,(103)晶向的优势得到进一步加强;(2)不同氧分压制备的CdS薄膜致密且粒径均匀,晶粒的大小随着衬底温度的升高而增大,但薄膜的粗糙度也随之增大;(3)随着CdS薄膜厚度的减小,可见光中短波段的透过率有所增大,有利于提高太阳电池的短波光谱响应。并将CSS制备的CdS多晶薄膜用于CdTe太阳电池的制作,获得了10.29%的光电转换效率,初步验证了该制作工艺的可行性。     

CdTe太阳电池中起因于Cu的深能级

在CdTe太阳电池中,易引入并形成Cu深能级中心. 本文采用深能级瞬态谱测试法研究了ZnTe背接触和石墨背接触CdTe太阳电池的部分深能级中心. 研究中运用密度泛函相关理论,分析闪锌矿结构CdTe,Cd空位体系和掺Cu体系的电子态密度,计算得出T_d场和C_3v场下Cu²⁺ d轨道的分裂情况. 计算结果表明,CdTe太阳电池中的E_v+0206 eV和E_v+0122 eV两个深中心来源于Cu替代Cd原子. 计算结果还表明,掺入Cu可降低CdTe体系能量.     

光谱分析气体状态对近空间升华沉积CdTe多晶薄膜的影响

在CdTe多晶薄膜太阳电池制备中用近空间升华法生长了CdTe多晶薄膜,沉积工作气体的状态决定了薄膜的结构、性质。文章首先分析了近空间沉积的物理机制,测量了近空间沉积装置内的温度分布,使用氩氧混合气体为工作气体,其中重点讨论了该气体状态(包括气氛和气压)与薄膜的初期成核的关系,即择优取向程度和光能隙与气氛和气压的关系。结果表明,(1)不同气氛下沉积的CdTe薄膜均为立方相结构。随氧浓度的增加,σ增加,氧浓度为6%时,σ最大,之后随氧浓度增加,σ降低,在12%达到最小,然后随氧浓度的增加而增加, 在氧浓度为9%时沉积的结晶更完整。CdTe薄膜的光能隙为1.50～1.51 eV;(2)在氩氧气氛下氧浓度为9%,不同气压下制备的样品,均有立方相CdTe, 此外, 还有CdS和SnO₂:F衍射峰。CdTe晶粒随气压增加有减小趋势,随气压的增加,透过率呈下降趋势,相应的CdTe吸收边向短波方向移动;(3)在氩氧气氛下氧浓度为9%,采用衬底温度550 ℃,源温度620 ℃,沉积时间4 min时制备的CdTe多晶薄膜获得了转换效率优良的结构为SnO₂:F/CdS/CdTe/Au的集成电池。     

具有高阻抗本征SnO2过渡层的CdS/CdTe多晶薄膜太阳电池

采用超声喷雾热解法制备了具有高阻抗的本征SnO₂透明导电膜，将其运用在CdS层减薄了的CdS/CdTe多晶薄膜太阳电池中，对减薄后的CdS薄膜进行了XRD,AFM图谱分析，并对电池进行了光、暗I-V，光谱响应和C-V测试.结果表明，在高阻膜上沉积的减薄CdS薄膜(111)取向更明显，但易形成微孔.引入高阻层后，能消除CdS微孔形成的微小漏电通道，有效保护p-n结，改善了电池的并联电阻、填充因子和短波响应，使载流子浓度增加，暗饱和电流密度减小，从而电池性能得到改善，电池转换效率增加了14.4%. 关键词： CdTe电池 过渡层 效率     

氧对于在Ar/O氛围下用近空间升华法制备的CdS薄膜的影响

采用近空间升华法（CSS）在氩/氧气氛中制备了硫化镉（CdS）多晶薄膜.利用XRD,XPS,AFM,UV-VIS光谱和四探针技术等测试和分析手段系统研究了氧对薄膜的成分、结构、光学和电学等性质的影响.结果表明,用近空间升华法制备的CdS薄膜具有六方相结构,膜层致密、均匀,平均晶粒大小约为40 nm,富硫.氧掺入后部分与镉生成氧化镉,并随着氧含量的增加,薄膜的成分有趋于化学计量比的趋势,光学带隙加宽,光暗电导比增加.此外,还利用扫描电镜（SEM）观察了CdS/CdTe断面结合光谱响应（QE）的结果讨论了氧对CdS/CdTe界面互扩散的影响.发现,随着CdS薄膜制备气氛中氧分压的升高,CdS/CdTe界面的互扩散程度降低,有利于提高器件在500—600 nm波长范围内的光谱响应.认为,氧含量的增加不但使CdS薄膜在光伏应用方面的质量得到改善,而且CdTe太阳电池器件中的CdS/CdTe界面也得到了优化. 关键词： CdS多晶薄膜 近空间升华法 窗口层 界面     

沉积条件对ZnTe/ZnTe:Cu薄膜结构及CdTe电池性能的影响

用共蒸发法沉积了ZnTe/ZnTe:Cu复合多晶薄膜,通过XRD,XPS,C-V,I-V等研究了沉积温度对薄膜结构、Cu浓度分布及电池性能的影响.结果表明,沉积温度对薄膜的结构影响不明显,薄膜呈立方相,经185 ℃退火后出现了六方相.对薄膜的剖析发现,Cu浓度分布呈现先上升到一极大值而后快速下降的趋势, 100 ℃沉积的ZnTe/ZnTe:Cu薄膜,ZnTe层起到了阻止Cu扩散作用,用这种薄膜制作的太阳电池X_D较大 关键词： ZnTe多晶薄膜 沉积温度 薄膜结构 器件性能     

Electronic properties and deep level transient spectroscopy of CdS/CdTe thin film solar cells

It is well known that preparing temperatures and defects are highly related to deep-level impurities. In our studies, the CdTe polycrystalline films have been prepared at various temperatures by close spaced sublimation (CSS). The different preparing temperature effects on CdS/CdTe solar cells and deep-level impurities have been investigated by I--V and C--V measurements and deep level transient spectroscopy (DLTS). By comparison, less dark saturated current density, higher carrier concentration, and better photovoltaic performance are demonstrated in a 580oC sample. Also there is less deep-level impurity recombination, because the lower hole trap concentration is present in this sample. In addition, three deep levels, E_v+0.341 eV(H4), E_v+0.226 eV(H5) and E_C-0.147 eV(E3), are found in the 580oC sample, and the possible source of deep levels is analysed and discussed.     

图谱分析退火对本征SnO2多晶薄膜性能的影响

提高CdTe太阳电池转换效率的有效途径之一是适当减薄CdS窗口层,减薄了的CdS层会严重影响电池性能,解决方法是在窗口层和透明导电膜之间加一层高阻本征SnO2薄膜。采用反应磁控溅射制备了具有高阻抗的本征SnO2薄膜,并对其进行了后处理,利用XRD,XPS等方法研究了退火前后薄膜的结构,成分及表面化学状态的变化。结果表明:经N2/O2=4:1气氛550℃(0.5h)退火后,样品由非晶态转变为四方相结构的多晶薄膜,具有(110)择优取向;XPS分析表明退火后薄膜的氧含量增加、O(1s)峰向低能方向移动,SnO被氧化成SnO2,使得薄膜的透过率增大,退火后的本征SnO2高阻膜非常适合作为过渡层应用于CdTe太阳电池中。     

Performance improvement in CdTe solar cells by modifying the CdS/CdTe interface with a Cd treatment

The performance of n-CdS/p-CdTe solar cells is often degraded under light soaking or thermal stress, even though the technology of CdTe solar cells is close to a commercial level. The Cu diffusion from a Cu back contact to a CdS window layer might degrade the cell's performance. To prevent the Cu diffusion, a very-thin intrinsic CdTe layer was introduced at the n-CdS/p-CdTe interface by depositing a very-thin Cd metal layer on the CdS film and converting the Cd metal into intrinsic CdTe during p-CdTe deposition at high temperature. By the Cd treatment on CdS surface, pinholes or voids were eliminated at the CdS/CdTe and the intermixing of Te and S at the interface was much suppressed. The depletion width was much increased and the intensity of LTPL peak was increased. The analysis suggested that an intrinsic CdTe interlayer was formed and the surface recombination rate was suppressed by the intrinsic interlayer. As a result, the short circuit current of the CdTe solar cell was significantly increased due the increased current gain in the blue wavelength region. The thermal stability of the CdTe solar cell was also greatly improved and the Cu diffusion was retarded by the intrinsic CdTe interlayer at the n-CdS/p-CdTe.     

Thermally evaporated CdS/CdTe thin film solar cells: Optimization of CdCl2 evaporation treatment on absorber layer

CdCl₂ treatment is crucial in the fabrication of highly efficient CdS/CdTe thin-film solar cells. This study reports a comprehensive analysis of thermal evaporated CdS/CdTe thin-film solar cells when the CdTe absorber layer is CdCl₂ annealed at temperatures from 340 to 440 °C. Samples were characterized for structural, optical, morphological and electrical properties. The films annealed at 400 °C showed better crystallinity with a cubic zinc blende structure having large grains. Higher refractive index, optical conductivity, and absorption coefficient were recorded for the CdTe films annealed at 400 °C with CdCl₂. Optimum photoactive properties for CdS/CdTe thin-film solar cells were also obtained when samples were annealed at 400 °C for 20 min with CdCl₂, and the best device exhibited V_OC of 668.4 mV, J_SC of 13.6 mA cm⁻², FF of 53.9% and an efficiency of 4.9%.     

Low temperature ferromagnetic properties of CdS and CdTe thin films

The magnetic property in a material is induced by the unpaired electrons. This can occur due to defect states which can enhance the magnetic moment and the spin polarization. In this report, CdS and CdTe thin films are grown on FTO glass substrates by chemical bath deposition and close-spaced sublimation, respectively. The magnetic properties, which are introduced from oxygen states, are found in CdS and CdTe thin films. From the hysteresis loop of magnetic moment it is revealed that CdS and CdTe thin films have different kinds of magnetic moments at different temperatures. The M–H curves indicate that from 100 K to 350 K, CdS and CdTe thin films show paramagnetism and diamagnetism, respectively.A superparamagnetic or a weakly ferromagnetic response is found at 5 K. It is also observed from ZFC/FC curves that magnetic moments decrease with temperature increasing. Spin polarized density functional calculation for spin magnetic moment is also carried out.     

CdTe/CdS太阳电池I-V，C-V特性研究

测量了CdTe太阳电池器件从50kHz至1MHz频率范围的电容-电压特性，计算了吸收层的载流子浓度和空间电荷区的位置，电容-电压特性测试结果出现两个峰，峰特征与测试频率有关，用多结模型进行模拟分析，解释了实验结果.测量了电池从220K至300K的变温暗电流-电压特性，得出电池的反向暗饱和电流密度J₀和二级管理想因子A，分析了J₀，A随测量温度的变化,并讨论了电池器件的电流特性. 关键词： CdTe太阳电池 电流-电压特性 电容-电压特性     

Recombination-induced voltage-dependent photocurrent collection loss in CdTe thin film solar cell

Recently, the efficiency of CdTe thin film solar cell has been improved by using new type of window layer Mg_xZn_1-xO (MZO). However, it is hard to achieve such a high efficiency as expected. In this report a comparative study is carried out between the MZO/CdTe and CdS/CdTe solar cells to investigate the factors affecting the device performance of MZO/CdTe solar cells. The efficiency loss quantified by voltage-dependent photocurrent collection efficiency (η_C(V')) is 3.89% for MZO/CdTe and 1.53% for CdS/CdTe solar cells. The higher efficiency loss for the MZO/CdTe solar cell is induced by more severe carrier recombination at the MZO/CdTe p—n junction interface and in CdTe bulk region than that for the CdS/CdTe solar cell. Activation energy (E_a) of the reverse saturation current of the MZO/CdTe and CdS/CdTe solar cells are found to be 1.08 eV and 1.36 eV, respectively. These values indicate that for the CdS/CdTe solar cell the carrier recombination is dominated by bulk Shockley—Read—Hall (SRH) recombination and for the MZO/CdTe solar cell the carrier recombination is dominated by the p—n junction interface recombination. It is found that the tunneling-enhanced interface recombination is also involved in carrier recombination in the MZO/CdTe solar cell. This work demonstrates the poor device performance of the MZO/CdTe solar cell is induced by more severe interface and bulk recombination than that of the CdS/CdTe solar cell.     

Understanding the junction degradation mechanism in CdS/CdTe solar cells using a Cd-deficient CdTe layer

It is known that CdTe solar cells are often degraded under solar illumination. But the degradation mechanism is not fully proved because it does not appear consistently. The junction degradation in CdS/CdTe solar cells was investigated using a CdTe layer with Cd deficient composition, where Cd vacancy concentration is high. It was found that the Cu atoms easily filled the Cd vacancies in CdTe and transport to junction area from Cu back contact. PL measurement and spectral quantum efficiency measurement showed that the incorporation of Cu atoms in CdS forms a defect energy level at 1.55 eV below the conduction band in CdS. As a result, the junction built-in potential is decreased and light penetration into CdTe absorber is shielded. For reliable and stable CdTe cells, the formation of Cd vacancy in CdTe should be avoided by careful control of CdTe.