雾化辅助化学气相沉积法氧化镓薄膜生长研究

采用自主设计搭建的雾化辅助化学气相沉积系统设备,开展了Ga₂O₃薄膜制备及其特性研究工作。通过X射线衍射研究了沉积温度、系统沉积压差对Ga₂O₃薄膜结晶质量的影响。结果表明,Ga₂O₃在425~650 ℃温度区间存在物相转换关系。随着沉积温度从425 ℃升高至650 ℃,薄膜结晶分别由非晶态、纯α-Ga₂O₃结晶状态向α-Ga₂O₃、β-Ga₂O₃两相混合结晶状态改变。通过原子力显微镜表征探究了生长温度对Ga₂O₃薄膜表面形貌的影响,从475 ℃升高至650 ℃时,薄膜表面粗糙度由26.8 nm下降至24.8 nm。同时,高分辨X射线衍射仪测试表明475 ℃、5 Pa压差条件下的α-Ga₂O₃薄膜样品半峰全宽仅为190.8″,为高度结晶态的单晶α-Ga₂O₃薄膜材料。     

Hierarchical motion planning at the acceleration level based on task priority matrix for space robot

Nonlinear Dynamics - A capacitive micromachined ultrasonic transducer (CMUT) due to many benefits is being considered as an imaging and therapeutic technology recently. The critical challenge is to...     

A multigrid method for the ground state solution of Bose–Einstein condensates based on Newton iteration

BIT Numerical Mathematics - In this paper, a new kind of multigrid method is proposed for the ground state solution of Bose–Einstein condensates based on Newton iteration scheme. Instead of...     

Numerical Investigation of Thermally Developing Non-Darcy Forced Convection in a Porous Circular Duct with Asymmetric Entrance Temperature Under LTNE Condition

Transport in Porous Media - This paper numerically investigates the heat transfer performance of thermally developing non-Darcy forced convection in a fluid-saturated porous medium tube under...     

全局优化问题的一个新的无参数填充函数

求全局最优化问题的填充函数算法被提出以来，参数的选取和调整一直是制约算法有效性的因素。如何在实际的计算过程中选取合适的参数，直接影响和决定了运算速度和效率。因此，构造不含参数的填充函数就显得极为重要。提出一个新的无参数的填充函数，对其理论性质进行了分析，并给出相应的填充函数算法，数值计算验证了算法的有效性。     

直接碳燃料电池燃料的研究进展

直接碳燃料电池(DCFC)是一种清洁高效利用碳资源发电的装置。其因能量转换率高,对环境污染小,燃料选择范围广等优点获得了越来越多的关注。DCFC的性能与使用的燃料密切相关,为了探究燃料对DCFC的影响,本文分别阐述了石墨、炭黑、中密度纤维板、生物质、煤、活性炭的特性及改性方法,分析讨论了燃料表面含氧官能团以及燃料中的金属催化剂对阳极电化学反应的促进作用,发现燃料表面化学性质要比比表面积更加重要。同时,本文也提出了对生物质这一优良的可再生资源的期待,为未来DCFC燃料的发展提供参考。     

Analysis on First-stage Ignition of n-Heptane at Low Temperatures with a Lumped Skeletal Mechanism

Two-stage ignition exists in the low-temperature combustion process of n-heptane and the first-stage ignition also shows a negative temperature coefficient(NTC) phenomenon. To study key reactions and understand chemical principles affecting the first-stage ignition of n-heptane, a lumped skeletal mechanism with 62 species is obtained based on the detailed NUIGMech1.0 mechanism using the directed relation graph method assisted by sensitivity analysis and isomer lumping. The lumped mechanism shows good performance on ignition delay time under wide conditions. The study revealed that the temperature after the first-stage ignition is higher and a larger amount of fuel is consumed at lower initial temperatures. The temperature at the first-stage ignition is relatively insensitive to the initial temperature. Further sensitivity analysis and reaction path analysis carried out based on the lumped mechanism show that the decomposition of RO₂ to produce alkene and HO₂is the most important reaction to inhibit the first-stage ignitions. The chain branching explosion closely related to the first-stage ignition will be terminated when the rate constant for the RO₂ decomposition is larger than that of the isomerization of RO₂ to produce QOOH. The NTC behavior as well as other characteristics of the first-stage ignition can be rationalized from the competition between these two reactions.     

陶瓷基功能材料载体纤维增强效果及机理

以陶瓷基功能材料载体为研究对象,按照其生产工艺配方,研究了纤维种类(莫来石、氧化铝、氧化锆)及其添加量对陶瓷基功能材料载体性能的影响.在相同实验条件且不影响其功能化参数前提下,将其与未添加纤维的空白试样力学性能进行对比.结果表明,试样经1200℃烧成后,相比莫来石与氧化铝纤维增强的陶瓷基功能材料载体,氧化锆纤维的增强效果最好.当氧化锆纤维的添加量为0.8 wt;时,试样的吸水率和气孔率均较低,分别为2.0;、4.0;,相比空白对比试样抗折强度增强了42.4;.     

Freeze–Thaw-Promoted Fabrication of Clean and Hierarchically Structured Noble-Metal Aerogels for Electrocatalysis and Photoelectrocatalysis

Noble-metal aerogels (NMAs) have drawn increasing attention because of their self-supported conductive networks, high surface areas, and numerous optically/catalytically active sites, enabling their impressive performance in diverse fields. However, the fabrication methods suffer from tedious procedures, long preparation times, unavoidable impurities, and uncontrolled multiscale structures, discouraging their developments. By utilizing the self-healing properties of noble-metal aggregates, the freezing-promoted salting-out behavior, and the ice-templating effect, a freeze–thaw method is crafted that is capable of preparing various hierarchically structured noble-metal gels within one day without extra additives. In light of their cleanliness, the multi-scale structures, and combined catalytic/optical properties, the electrocatalytic and photoelectrocatalytic performance of NMAs are demonstrated, which surpasses that of commercial noble-metal catalysts.