有效集法在数学规划加权残值法中的应用

本文研究有效集法在数学规划加权残值法求解微分方程问题中的应用。从理论上和实际应用方面 阐明，对于数学规划加权残值法和线性规划问题，有效集法比常用的单纯形法更简便、易程序化、计算速度更快，因此更适用于数学规划加权残值法求解微分方程问题。     

化学跑合对齿轮胶合的影响

选用了３ 种跑合剂在ＣＬ－１００ 型齿轮试验机上进行满载跑合能力对比试验和齿轮抗胶合载荷级对比试验．结果表明：材质为４５＃ 钢的试验齿轮副和材质为２０ＣｒＭｎＴｉ钢的试验齿轮副用含磨料跑合剂进行１ 次满载跑合试验时,发生严重胶合;而采用化学跑合剂可以实现１ 次满载跑合,且用化学跑合剂跑合后的齿面比用普通油跑合后的齿面抗胶合能力提高１ 个载荷级,显示化学跑合剂在齿轮中的应用很有潜力．     

连通容器泄爆过程的影响因素

以甲烷/空气混合物为研究对象,开展了连通容器气体泄爆影响因素的实验研究。结果表明:连通容器泄爆片泄爆时,随着破膜压力和量纲一泄压比的减小,大、小球容器的最大泄爆压力均增大;在等量纲一泄压比条件下,随着连接管道长度的增加,传爆容器的最大泄爆压力增大。连通容器无膜泄爆时,大球点火条件下,无论管长如何,起爆容器和传爆容器均比单个容器最大泄爆压力大。小球点火条件下,当管道长度为0.45 m时,起爆容器和传爆容器的最大泄爆压力均小于单个容器。连通容器无膜泄爆且量纲一泄压比相同时,当管道长度为0.45 m时,大、小容器内的最大泄爆压力基本相等;当管道长度为2.45 m时,大容器点火时,传爆容器最大爆炸压力大于起爆容器,但小容器点火时,起爆容器最大泄爆压力大于传爆容器;当管道长度为4.45和6.45 m时,传爆容器最大泄爆压力均大于起爆容器。     

Experimental investigation of converging shocks in water with various confinement materials

Fluid-solid coupling typically plays a negligible role in confined converging shocks in gases because of the rigidity of the surrounding material and large acoustic impedance mismatch of wave propagation between it and the gas. However, this is not true for converging shocks in a liquid. In the latter case, the coupling can not be ignored and properties of the surrounding material have a direct influence on wave propagation. In shock focusing in water confined in a solid convergent geometry, the shock in the liquid transmits to the solid and both transverse and longitudinal waves propagate in the solid. Shock focusing in water for three types of confinement materials has been studied experimentally with schlieren and photoelasticity optical techniques. A projectile from a gas gun impacts a liquid contained in a solid convergent geometry. The impact produces a shock wave in water that develops even higher pressure when focused in the vicinity of the apex. Depending on the confining material, the shock speed in the water can be slower, faster, or in between wave speeds in the solid. For solid materials with higher wave speeds than the shock in water, regions in the water is put in tension and cavitation occurs. Materials with slower wave speeds will deform easily.     

Response of glass-fiber-reinforced epoxy specimens to high rates of tensile loading

The object of this investigation is to establish experimentally the mechanical properties, and the mode of failure of glass-fiber-reinforced epoxy plates subjected to high rates of strain (30,000 in./in./min), in the direction of the fibers, on a specially designed impact-loading machine propelled by explosives. The results are correlated with those obtained by testing glass-fiber-reinforced epoxy plates subjected to various low rates of strain (0.0265 in./in./min, 0.66 in./in./min and 26.5 in./in./min).     

Prefacein：in dedication to Professors Yong Jin and Zhiqing Yu

This special issue of China PARTICUOLOGY is dedicated to Professors Yong Jin and Zhiqing Yu of Tsinghua University, China, to celebrate over five decades of their careers in chemical engineering research and education. Prof. Jin graduated in 1959 from Ural Polytechnic College in Svivdelovsk in the former USSR and then completed his post-graduate studies in Tianjin University in China in 1960. Thereafter, he taught at the Chinese University of Science and Technology for 13 years before joining Tsinghua University in 1973. Prof. Yu graduated in 1956 from Tianjin University in China and joined Tsinghua University thereafter. Between 1957 and 1959, Prof. Yu undertook more studies in Moscow Mendeleev Institute of Chemical Technology in the former USSR. During the 1970s, Professors Jin and Yu jointly created the Reaction Engineering Program in the Department of Chemical Engineering at Tsinghua University, which later became one of the largest fluidization research groups in the world, known as FLOTU - Fluidization Laboratory of Tsinghua University.     

Remarks on the Behavior of Simple Directionally Reinforced Incompressible Nonlinearly Elastic Solids

The effect of directional reinforcing in generating qualitative changes in the mechanical response of a base neo-Hookean material is examined in the context of homogenous deformation. Single axis reinforcing giving transverse isotropy is the major focus, in which case a standard reinforcing model is characterized by a single constitutive reinforcing parameter. Various qualitative changes in the mechanical response ensue as the reinforcing parameter increases from the zero-value associated with neo-Hookean response. These include (in order): the existence of a limiting contractive stretch for transverse-axis tensile load; loss of monotonicity in off-axis simple shear; loss of monotonicity in on-axis compression; loss of positivity in the stress-shear product in off-axis simple shear; and loss of monotonicity for plane strain in on-axis compression. The qualitative changes in the simple shear response are associated with stretch relaxation in the reinforcing direction due to finite rotation. This revised version was published online in August 2006 with corrections to the Cover Date.     

岩体中非填实爆炸空腔壁振动状态分析

采用流体动力学模型研究了地下空腔中化学爆炸冲击波的传播过程及空腔壁的运动状态。计算中体现了空气冲击波与空腔壁作用后激发的强谱振幅高频冲击波。在实验中 ,解决了空腔内传感器的防护和抗干扰等技术难题 ,测到了空腔壁的地运动加速度波形。通过对所测波形的时频域分析得出了非填实爆炸在源区和近区激发高频应力波 ,其频率明显高于填实爆炸的频率。这些特征与数值计算相一致。最后简略讨论了数值计算与实验测量中需解决的问题。     

Heat (mass) transfer and friction loss in two-pass ducts with various parallel rib arrangements

The present study investigated the effects of four parallel rib arrangements on heat/mass transfer and pressure drop characteristics in rotating two-pass ducts. The experiments of mass transfer and pressure measurement are performed to obtain heat transfer distributions and friction losses. The highest averaged heat (mass) transfer and friction loss in each region appeared in the turning region in the stationary cases, but appeared in the upstream region of the second pass in the rotating cases. Among the tested rib arrangements, the averaged heat (mass) transfer and the friction factor in the second pass in the stationary ducts were high in the cases with the NN- and PP-type ribs; however, in the rotating ducts, they were high in the cases with the NN- and PN-type ribs. The thermal performance in the four different rib arrangements was almost the same.     

Measurements of Deflection and Residual Stress in Thin Films Utilizing Coherent Light Reflection/Projection Moiré Interferometry

Thin film technology is an area of great importance in current applications of opto-electronics, electronics, MEMS and computer technology. A critical issue in thin film technology is residual stresses that arise when the coating is deposited onto a substrate. Residual stresses can be very large in magnitude and have detrimental effects on the role that the thin film must play. To save development time on coating deposition processes it is important to perform accurate residual stresses measurements in situ in real time where the deposition is made. A novel optical set up is developed in this study to measure deflections and residual stresses generated in coated specimens that can be applied directly in the reactor utilized in the deposition process. Experimental results are in good agreement with other measurements carried out independently and other data reported in literature for thin films like those tested in the experiments.     

Application of ultrasonic-pulse-spectroscopy measurements to experimental stress analysis

We apply the technique of ultrasonic pulse spectroscopy to measure the interference effects between two shear waves propagating in specimens loaded in uniaxial compression. We show that the power spectrum of an echo containing both fast and slow components of a shear wave will exhibit periodic minima. The periodicity exhibited in the spectrum is 1/Δτ, where Δτ is the difference in arrival time between the fast and slow waves. A change in the state of stress which produces a change in the two shear velocities results in a stress-dependent change in wave-arrival times. Because of this velocity change, the frequency at which a particular minimum occurs in the spectrum changes, and this can be used to indicate the state of stress in the material. Our results indicate that, if the spectrum minima frequencies could be resolved to within 10 kHz, the principal-stress differences within 36 psi (0.251 MPa) could be measured in specimens of aluminum 1 in. (2.54 cm) thick. Inherent in analyzing and measuring echo-interference effects is a single-echo requirement. Thus, transducer coupling effects are minimized and measurements in highly attenuating materials or at high frequencies in normal attenuating materials are possible. This technique shows considerable promise as a means of measuring and monitoring the applied stresses in materials.     

盐岩储库区地面沉降预测与控制研究现状与展望

利用盐岩地层建设地下油气储库群已成为各国发展能源储备的重要方向,然而关于储库区地面沉降的研究至今仍处于探索阶段。由于地面沉降所造成的重大事故屡见不鲜,因此有必要集中力量研究盐岩库区地面沉降问题,为我国盐岩储库群的建设提供可靠的理论依据。本文主要从以下3个方面总结了近几十年来国内外学者在盐岩储库区地面沉降预测方面所做出的努力与成绩： （1）现场监测——法国、德国、美国先后建立了现场监测网络,获得了大量的长期监测数据;  （2）理论计算——我国学者于20世纪90年代末将随机介质理论引入到盐矿水溶开采地面沉降预测中,从而为储库区地面沉降预测提供了新的理论基础;  （3）数值模拟——欧洲学者利用FLAC2D 程序对盐岩储库区的地面稳定性进行了数值模拟,而我国学者则利用在新概率积分法的基础上建立起的预测模型成功进行了沉降预测模拟。此外,为了有效地控制库区地面变形,预留矿柱式水溶开采法在国外众多盐岩地下储库群建设中得以广泛应用。本文最后提出在后续研究中将重点着眼于地表变形随时间的发展过程,并对现有理论模型进行适当的修正以及利用现场实测数据进一步完善预测所需参数的选取方法,从而使预测结果更为准确可靠。     

Ultrasonic measurement of the bending of a bolt in a shear joint

An ultrasonic pulse/echo technique is used to measure preload in bolts used in structural joints. In this paper, the same instrument is used in a different way to measure change in the ultrasonic measurements due to bending in the bolts. A theory that explains the ultrasonic measurements is developed. The bending loads result in a rotation and a translation of the ultrasonic pulse reflecting face. It also creates a stress gradient in the bolt. This results in a phase variation (or gradient) in the received ultrasonic beam across the face of the transducer. It also results in a physical shift in the received beam relative to the ultrasonic transducer. The phase gradient and the shift in the beam results in change in the pulse travel time. A number of experiments were performed on the bolt to study the effect of the bending on the ultrasonic measurements. The experiments and the theory validate a sensitive new method for measuring the bending loads in the bolts.     

Mathematical simulation of hydrodynamic generators of oscillations

Unsteady turbulent swirled water flow in a channel in the presence of cavitation is calculated. It is shown that in the near-axial channel zone a fluctuating vapor region, or cavity, arises and variations in the cavity shape and dimensions lead to the onset of undamped pressure fluctuations. The amplitude-frequency characteristics of the oscillations are obtained in different channel cross-sections. The amplitude maximum position in the channel expansion zone is in agreement with the available experimental data. The dynamics of toroidal vortices formed in the hydrodynamic generator channel and in the expansion zone at its exit are established.     

关于渗流中流线不封闭的特性和条件

本文对于流体在多孔介质中流动的特性进行理论研究和数值计算，提出两个关于渗流中流线不封闭的特性和条件，得到了在一般工程实际情况中的多孔介质区域内部不存在封闭流线的结论。本文以突变截面圆管中不可压缩渗流为算例，利用半人工瞬变方法进行数值计算，得到流体在充满多孔介质的突扩截面圆管和突缩截面圆管中流动时关于速度分布和压力分布的结果。由此表明，在突变截面附近的渗流区域中不存在回流和分离流，也不存在封闭的流线。渗流的这些流动特性不同于在无多孔介质的空间区域中的流动特性。     

Effects of external electric field on pool boiling: Comparison of terrestrial and microgravity data in the ARIEL experiment

Pool boiling in microgravity, in the presence of an electric field or less, was investigated in ARIEL test setup, integrated in Fluidpac facility, on Foton-M2 orbital mission. The nucleate boiling curve with FC-72 was measured in terrestrial and reduced gravity conditions, on a heated surface whose size was relevant from a technical point of view, for various degrees of fluid subcooling and high heat rates. An external electrostatic field was also added to investigate its use as a possible replacement of buoyancy. Counterpart tests were carried out in the same apparatus in normal gravity, before the mission. The present paper deals in particular with the comparison between boiling performance in normal and reduced gravity in the entire experimental range.     

氡射气测量在西安地裂缝勘察中的应用研究

为了避免大量开挖揭露工作量, 加快地裂缝的勘察速度, 研究出一种简便易行的探测方法是目前西安地裂缝勘察中迫切需要解决的问题。本文研究了氡射气测量在西安地裂缝勘察应用的地质基础, 结合近十几年工程勘察实践, 讨论了氡射气异常的特征, 分析了氡射气的探测效果, 结果认为：氡射气测量在西安地裂缝探测中的有效率为：８０％左右。     

Heat exchange between a gas bubble and a liquid

The nonlinear problem of thermal and dynamic interaction between a single gas bubble and surrounding liquid is considered. This problem is met in studies of gas-liquid mixture flows, in particular, in Shockwave propagation in such media. A numerical solution is presented for various modes of bubble surface radial motion. The modes correspond to bubble behavior directly beyond a shock-wave front, where the latter enters the bubble screen, and to the behavior of a bubble located in the depths of the bubble curtain, where the wave becomes diffuse. Analytic solutions of the linearized problem of thermal conductivity for free and constrained small harmonic oscillations of a gas bubble in a liquid were obtained in [1, 2]. Cooling of a hot gas bubble was considered in [3], that study, however, contains inaccuracies. In particular, it was assumed in the solution that the gas density in the bubble was homogeneous. The equation for heat flux in dimensionless variables was written inaccurately. However, in the examples considered in [3] these inaccuracies do not lead to significant errors in the numerical results.     

双柱单锥型液-液旋流管内流场的激光诊断

应用激光测速仪，对一种双柱单锥型液 液旋流管内的流动结构，进行了全场范围内的多工况流动诊断研究．揭示出其切向速度由内旋流区和外旋流区构成，其中内旋流区中的速度分布符合准强制涡关系，外旋流区中的速度分布符合准自由涡关系；轴向速度由上行流动区和下行流动区构成，两者之间在直管段以零速点作分界，在锥体段则以零速区作过渡并伴随有一定的回流出现，且该过渡区或回流区的大小随锥体截面的收缩而减小，直到进入直管段后消失；各湍流量的分布以管芯处最大向外逐渐减小，沿轴向是直管段中的湍流度大于锥体段中的湍流度，而且湍流度在旋流管内具有各向异性的特性．