毛细管区带电泳分离硝基苯胺位置异构体的研究

采用毛细管区带电泳(CZE)技术,在极端pH值条件下分离了邻、间、对硝基苯胺位置异构体;研究了背景缓冲溶液、pH值、分离电压、温度及进样时间等因素对分离的影响,得出了3种样品的标准曲线、线性范围及加样回收率。在选定的实验条件下15min内实现了上述3种苯胺类化合物的分离。该方法快速,准确,重现性好。     

毛细管区带电泳对羟基苯甲酸三种异构体的分离研究

考察了邻羟基苯甲酸、间羟基苯甲酸和对羟基苯甲酸在毛细管区带电泳分离时的行为。研究了缓冲液pH、浓度和分离电压对三种羟基苯甲酸异构体分离的影响,结果表明在10 mmol/L Na2HPO4缓冲体系(pH 10.15),运行电压25kV,实验温度25℃的分离条件下,采取压力进样(3.4 kPa×3 s),检测波长210nm;3种异构体在7 min内获得基线分离。邻羟基苯甲酸、间羟基苯甲酸、对羟基苯甲酸在2~100μg/mL范围内,峰面积与质量浓度具有较好的线性关系,检出限分别是0.96,1.27和1.07μg/mL。     

毛细管区带电泳同时分离苯二酚和硝基苯酚位置异构体

运用毛细管区带电泳模式,通过在缓冲溶液中添加有机溶剂成功地分离了邻、间、对苯二酚和邻、间、对硝基苯酚两组位置异构体。研究了缓冲溶液种类、浓度、pH值、电泳电压、温度、进样时间及有机溶剂等因素对分离的影响,得出了6种样品的标准曲线、线性范围及加样回收率。在优化条件下,10min内实现了上述6种酚类化合物的分离。该方法简便、快速、重现性好。     

毛细管区带电泳法同时分离测定香兰素和邻位香兰素异构体

建立了同时测定香兰素和其异构体邻位香兰素的毛细管区带电泳法(CZE)。考察了缓冲溶液的种类、浓度和pH以及分离电压等因素对分离结果的影响。在缓冲溶液为50 mmol/L硼砂-150 mmol/L磷酸氢二钠(pH 7.5)、分离电压15 kV的优化条件下,6 min内即可实现分离。香兰素和邻位香兰素在10～240 mg/L范围内线性关系良好,相关系数分别为0.9999和0.9997;方法的检出限均为1.0 mg/L (信噪比为3);样品的加标回收率为99.4%～101.2%,相对标准偏差为0.19%～0.73%。该方法操作简单、快速,已应用于实际样品的分析,并获得了令人满意的结果。     

羟基苯甲酸的3种异构体的毛细管区带电泳分离研究

 采用十六烷基三甲基溴化铵 (CTAB)为电渗流改性剂 ,考察了邻羟基苯甲酸、间羟基苯甲酸和对羟基苯甲酸在高效毛细管区带电泳模式下的分离行为 ,研究了缓冲液的pH和添加剂甲醇的用量对这 3种同分异构体的分离、峰形和出峰顺序的影响 ,并据此优化了这 3种异构体的分离条件。     

胶束电动毛细管色谱法分析头孢哌酮与其S-异构体等杂质

以十二烷基硫酸钠(SDS)胶束为准固定相,考察了头孢哌酮、头孢哌酮S-异构体、头孢哌酮杂质A及其他未知杂质在胶束电动毛细管色谱(MECC)分离模式下的分离行为。研究了运行缓冲液的pH值、磷酸盐浓度、SDS浓度、甲醇体积分数、分离电压、分离温度等因素对头孢哌酮、S-异构体、头孢哌酮杂质A及其他杂质的迁移时间、分离度以及可分离出的杂质个数的影响。结果发现,这些因素对头孢哌酮与诸杂质间的分离及检测有显著的影响,尤以pH值为最。它不仅影响它们的迁移时间和分离效率,还直接影响头孢哌酮及其杂质峰的检测。优化后的分离条件:运行缓冲液为70 mmol/L磷酸盐-100 mmol/L SDS (pH 6.5),分离电压为15 kV,分离温度为25 ℃。在此条件下,用非涂渍石英毛细管51.0 cm×75 μm(有效长度42.5 cm),压力进样5 kPa×5 s,在254 nm波长下进行检测,可分离出28个杂质,诸杂质彼此间及与头孢哌酮间可得到有效分离。并将该方法成功地用于测定注射用头孢哌酮钠的含量和有关物质,结果令人满意。     

低pH毛细管区带电泳法分离寡核苷酸和硫代反义寡核苷酸

在低pH条件下采用毛细管区带电泳法对寡核苷酸(PO-ODNs)及具有药用价值的硫代反义寡核苷酸(PS-ODNs)药物“癌泰得”系列样品(18~20 mers)进行分离,并系统考察优化了缓冲溶液的pH、缓冲溶液的种类及浓度、添加剂的种类及浓度、电压、温度等因素对样品单碱基分离的影响。其中缓冲溶液的pH对分离起决定性的作用,而添加剂尿素的加入显著提高了PS-ODNs样品的分离度。结果表明,采用未涂层弹性石英毛细管(50 μm,总长49.0 cm,有效长度40.7 cm),以50 mmol/L磷酸二氢钠-磷酸(pH 2.24)-7 mol/L尿素为缓冲溶液,压力进样(2 kPa×10 s),负极进样,正极检测,在分离电压20 kV、柱温25 ℃、检测波长260 nm条件下,可实现寡核苷酸及硫代反义寡核苷酸混合样品的单碱基分离。PO-ODNs的18～19 mers及19~20 mers样品的平均分离度分别为4.68,3.20;PS-ODNs的18～19 mers及19~20 mers样品的平均分离度分别为1.23及0.81。该法操作简单,重现性好,可为反义寡核苷酸药物的分析提供借鉴。     

低pH毛细管电泳法分离测定菠菜中的甜菜碱

建立了毛细管电泳法快速测定菠菜中甜菜碱的方法。通过与对溴代苯甲酰甲基溴反应,将甜菜碱转化成苯甲酰甲基酯后进行测定。研究了缓冲液的pH、分离电压以及结构相似化合物等因素对分离的影响,优化并确定了分离条件:75μm ID×50/57 cm(分离长度/总长)未涂层石英毛细管,分离电压15 kV,实验温度25℃,缓冲溶液100 mmol/L H3PO4-H3PO4盐,pH 2.91,检测波长262nm。在浓度范围5.8~580μg/mL之间,线性关系良好,y=72221x 4042.5,R2=0.9999,回收率在94.5%~99.8%之间。     

微波消解-毛细管电泳法测定茶叶中的生物碱

应用微波消解-毛细管电泳法测定3种茶叶中的咖啡因、腺嘌呤及儿茶素类化合物.优化了缓冲溶液体系、浓度、pH及分离电压等实验条件.在最佳实验条件下,以30 mmol/L硼砂-10 mmol/L β-环糊精为缓冲溶液,pH为9.0,分离电压为22 kV,检测波长为280 nm,电动进样20 kV×5s时,在7 min内同时分...     

糖类衍生物在毛细管区带电泳下的分离研究

以新合成的1-萘基-3-甲基-5-吡唑啉酮(NMP)为柱前衍生试剂,采用毛细管区带电泳模式考察并优化了糖类衍生物的分离条件。实验采用58.5cm×50μmi.d.毛细管(有效柱长50cm),55mmol/L硼酸盐缓冲溶液(pH9.46),柱温20℃,分离电压22kV,进样10s,在不加任何添加剂的情况下,高效、快速地实现了9种糖的基线分离,并在最优化条件下进行了唐古特白刺实际样品的分离分析,结果令人满意。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.