CuO-ZnO基CO2/H2合成甲醇催化剂的反应活性中心

应用 ＸＰＳ，ＸＡＥＳ和紫外漫反射光谱法研究了ＣｕＯ－ＺｎＯ／氧化物上ＣＯ２／Ｈ２合成甲醇的反应活性中心。ＣｕＯ－ＺｎＯ／氧化物催化剂上的反应活性中心是存在于ＣｕＯ－ＺｎＯ固溶体中的Ｃｕ－口－Ｚｎ－Ｏ（＂口＂为氧空位），活性中心的Ｃｕ价态为Ｃｕ＾＋和Ｃｕ＾０。反应活性中心在ＣｕＯ－ＺｎＯ－Ｚｒｏ２催化剂上比在其它ＣｕＯ－ＺｎＯ／氧化物催化剂如ＣｕＯ－ＺｎＯ，ＣｕＯ－ＺｎＯ－ＭｇＯ，ＣｕＯ－ＺｎＯ－     

二氧化碳加氢合成甲醇铜基催化剂表面组成的研究

本文分别采用ＸＲＤ、ＥＳＲ、ＸＰＳ和ＸＡＥＳ等技术对于二氧化碳加氢低压合成甲醇用ＣｕＯ，ＣｕＯ－ＺｎＯ，ＣｕＯ－ＺｎＯ－Ａｌ＿２Ｏ＿３，ＣｕＯ－ＺｎＯ－ＺｒＯ＿２催化剂在不同条件下表面Ｃｕ、Ｚｎ、Ａｌ、Ｚｒ的存在价态进行了深入分析。实验发现催化剂在还原前Ｃｕ以Ｃｕ￣２＋存在，在还原后和反应状态下以Ｃｕ￣０存在；Ｚｎ在还原后和反应状态下有部分被还原为Ｚｎ￣（２－δ）（０＜δ＜２），Ｚｒ和Ａｌ仍保持其还原前价态。催化剂的表面化学组成为：Ｃｕ￣０／Ｚｎ（２－δ）￣＋／Ｚｒ￣４＋／Ａｌ￣３＋／Ｏ￣２－。     

CO2加H2合成甲醇Cu—Zn—O催化剂表面化学态研究

应用ＸＲＤ、ＥＳＲ、ＵＲＤＳ、ＸＰＳ及ＸＡＥＳ等手段研究了ＣＯ２加Ｈ２合成甲醇Ｃｕ－Ｚｎ－Ｏ催化剂在还原后和反应状态下的表面化学状态。结果表明，在还原及反应状态下，催化剂表面仅能检测到ＣＵ＾０，而未发现稳定的Ｃｕ＾２＋和Ｃｕ＾＋存在；ＺｎＯ被 部分还原产生低价锌Ｚｎ＾（２－δ）＋（０＜δ＜２）。关联活性测试结果认为：Ｃｕ＾ｏ／Ｚｎ＾（２－δ）＋Ｏ构成ＣＯ２加Ｈ２合成甲醇反应的活性中心。     

助剂对超细CuO－ZnO－SiO_2催化剂性质和CO_2加氢反应性能的影响

研究了９种助剂对用于ＣＯ２加氢反应的超细ＣｕＯ－ＺｎＯ－ＳｉＯ２催化剂性能的影响，并进行了ＸＲＤ和ＴＰＲ表征．结果表明，助剂影响超细催化剂的性质和催化性能，ＴｉＯ２、ＣｅＯ２、ＭｇＯ和Ｌａ２Ｏ３是ＣＯ２加氢合成甲醇的超细ＣｕＯ－ＺｎＯ－ＳｉＯ２催化剂体系的优良助剂．在含有不同助剂的ＣｕＯ－ＺｎＯ－ＳｉＯ２催化剂体系内存在ＣｕＯ和ＺｎＯ晶相，但除ＣｅＯ２以外，其它的助剂都可能以微晶或无定型的形式存在．ＴＰＲ研究表明，添加的助剂除ＣｅＯ２以外，都使超细ＣｕＯ－ＺｎＯ－ＳｉＯ２催化剂的还原温度提高，而且助剂对ＣｕＯ－ＺｎＯ－ＳｉＯ２催化剂活性的影响，按照助剂对ＣｕＯ－ＺｎＯ－ＳｉＯ２催化剂还原温度的影响进行了探讨     

甲烷部分氧化制合成气Ⅱ．镍系催化剂的反应性能

主要用第四周期金属元素的氧化物与Ａｌ２Ｏ３的复合氧化物催化剂上甲烷氧化的结果证实了催化剂设计中的预测：（１）催化剂首先应能解离活化甲烷，（２）催化剂要能较快地活化Ｏ２分子．只有同时满足这两个条件，催化剂才可能有较好的甲烷部分氧化活性．第四周期元素中只有镍具有这样的性质．Ｃｕ，Ｍｎ，Ｃｒ，Ｌａ，Ｃａ，Ｚｎ等氧化物的添加可明显提高Ｎｉ－Ａｌ２Ｏ３催化剂的甲烷部分氧化性能，其中Ｃｕ的助催化性能最好．催化剂ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３，ＮｉＯ－ＭｎＯ－Ａｌ２Ｏ３，ＮｉＯ－Ｃｒ２Ｏ３－Ａｌ２Ｏ３的反应活性和选择性顺序，与金属Ｃｕ，Ｍｎ，Ｃｒ上ＣＯ和Ｈ２脱附的顺序是一致的     

甲醇与乙醇一步合成异丁醛用CuO-ZnO/Al2O3催化剂

在ＣｕＯ－ＺｎＯ／Ａｌ２Ｏ３催化剂上，甲醇与乙醇在常压和２１０￣３６０℃温度下一步反应合成异丁醛。利用正交设计方法，研究了ＣｕＯ－ＺｎＯ／Ａｌ２Ｏ３体系催化剂组成和制备条件等因素对催化剂催化性能的影响。结果表明，催化剂中ＣｕＯ含量对催化剂的催化活性影响最大，而ＺｎＯ含量则主要影响催化剂对异丁醛的选择性。催化剂制备条件，如沉淀温度、陈化时间等，也不同程度也影响催化剂的催化性能。ＸＲＤ和ＢＥＴ表征结果     

Cu／ZnO／Al_2O_3／ZrO_2催化剂上乙醇脱氢合成乙酸乙酯Ⅱ．催化剂的表征

采用ＸＲＤ，ＴＰＲ和ＴＰＤ／ＴＰＳＲ方法研究了ＣｕＯ／ＺｎＯ／Ａｌ２Ｏ３／ＺｒＯ２（及还原态）催化剂的物相结构、还原状况、酸碱性质及吸附状况，并与其它催化剂作了比较．ＸＲＤ结果表明，此催化剂在还原前有以晶相存在的ＣｕＯ，还原后以铜晶形式存在，而Ａｌ２Ｏ３，ＺｎＯ，ＺｒＯ２在还原前后均以无定形形式存在．ＴＰＲ实验发现，共沉淀法制备的铜基催化剂只有一个耗氢峰，对应ＣｕＯ的一种分布状态，且催化剂中ＺｒＯ２的存在促进了催化剂的还原．ＮＨ３－ＣＯ２双组分共吸附结果表明，ＣｕＯ／ＺｎＯ／Ａｌ２Ｏ３／ＺｒＯ２催化剂上有两种强度不同的酸中心（１００℃，３４０℃）及弱碱中心（９０℃）．乙醇在催化剂上的ＴＰＳＲ结果表明，在１１０℃有乙醇的脱附峰，氢气及乙醛的生成峰在２１０℃，而在高温时则有ＣＯ，ＣＯ２及丙酮的脱附，整个过程中仅检测到微量乙酸乙酯的脱附（ｍ／ｅ＝４３）     

Cu／ZnO／Al_2O_3／ZrO_2催化剂上乙醇脱氢合成乙酸乙酯Ⅰ．催化反应性能及机理

研究了经ＺｒＯ２改性的Ｃｕ／ＺｎＯ／Ａｌ２Ｏ３的催化性能，考察了操作条件、ＺｒＯ２含量及不同原料的影响．发现经共沉淀法制备的Ｃｕ／ＺｎＯ／Ａｌ２Ｏ３／ＺｒＯ２具有最佳的反应活性及选择性．以９５％乙醇为原料，在２６５℃，ＷＨＳＶ１．５ｈ－１时，乙醇转化率为６９．０％，乙酸乙酯选择性为７０．２％．使用无水乙醇为原料要好于９５％乙醇，使用乙醛或醇醛混合原料，亦有乙酸乙酯生成．乙醇在此催化剂上的反应机理为乙醇先在Ｃｕ上脱氢为乙醛，然后乙醛在酸碱双中心上发生Ｃａｎｎｉｚａｒｒｏ反应生成乙酸乙酯．还讨论了ＺｒＯ２的作用及催化剂活性降低的原因     

CuO／CeO_2／γ－Al_2O_3催化剂的结构及氧物种

应用ＸＲＤ、ＥＳＲ及ＸＰＳ方法研究了ＣｕＯ／ＣｅＯ２／γ－Ａｌ２Ｏ３催化剂的体相及表面结构，并对催化剂表面氧物种进行了表征．实验结果表明，ＣｅＯ２使Ｃｕ２＋还原为低价钢离子和增加钢化合物的分散性．催化剂中ＣｅＯ２含量高时，表面有Ｏ２－和Ｏ－物种，而ＣｅＯ２含量低时，只有Ｏ２－物种．     

氧化锆对铜基甲醇合成催化剂的促进作用(英文)

采用离子掺杂价态补偿原理,在Ｃｕ－Ｚｎ－Ａｌ甲醇合成催化剂中添加适量氧化锆助剂研制Ｃｕ－Ｚｎ－Ａｌ－Ｚｒ催化剂的特性。实验结果表明,最佳反应温度为２３０℃,比Ｃｕ－Ｚｎ－Ａｌ约低１０℃。采用ＸＲＤ、ＵＶＤＲ、ＦＴＩＲ、ＴＰＤ和ＴＰＲ等谱学方法对２种催化剂进行表征显示,铜基催化剂的活性位可能是“Ｃｕ０－Ｃｕ＋－Ｏ－Ｚｎ２／Ａ２Ｏ３－ＺｒＯ２”,工作态Ｃｕ－Ｚｎ－Ａｌ－Ｚｒ催化剂表面上Ｃｕ／Ｃｕ０的比值、价态稳定性和对ＣＯ的吸附量均大于Ｃｕ－Ｚｎ－Ａｌ,这与该催化剂具有较好的低温活性和较高的热稳定性密切相关。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.