低温等离子体原子荧光光谱法直接测定固体样品中的汞

建立了低温等离子体(LTP)与原子荧光光谱仪(AFS)联用直接检测ABS固体样品中Hg的方法.实验采用介质阻挡放电(DBD)方式产生低温等离子体,剥蚀固体样品后产生的元素蒸气引入到原子荧光光谱仪进行检测.优化的实验条件为:DBD外接电源的放电功率为16～18 W,放电气体流速为400 mL/min;采样距离为1～5 mm;原子荧光光谱仪的原子化器高度为10 mm.本系统测定Hg的检出限为0.91 mg/kg,线性范围为91.5～1096 mg/kg;精密度(RSD,n=7)为1.9％～2.3％,并对标准样品以及实际样品进行测定,测定结果与标准值与ICPMS及CVG-AFS一致,表明本方法可作为直接检测固体样品的新型元素分析技术.     

激光剥蚀-电感耦合等离子体质谱法测定多晶硅中杂质元素

采用激光剥蚀固体进样技术结合电感耦合等离子体质谱法测定了多晶硅中的元素B、Cu和Zn。考察了该三种杂质元素在多晶硅样品不同深度层面和同一深度层面的分布情况;尝试了采用硅基体信号归一化的方法计算了测定元素的含量。结果表明,杂质元素B、Cu和Zn在多晶硅材料中分布均匀,且测定结果与辉光放电质谱法的测定结果相吻合。这一方法可用于判别多晶硅表面的污染情况,以及杂质元素在多晶硅材料内部分布的均匀性。     

介质阻挡放电等离子体-Cu-Ni/γ-Al2O3催化剂体系在甲烷二氧化碳重整反应中的协同作用

将介质阻挡放电(DBD)等离子体与Cu-Ni/γ-Al<,2>O<,3>催化剂结合用于甲烷二氧化碳重整制合成气.结果表明:DBD等离子体与催化剂之间产生明显的协同作用,与单纯放电或是单纯催化相比较,DBD等离子体与催化剂相结合极大地提高了反应活性及稳定性.通过XRD,H<,2>-TPR,XPS及O<,2>-TPO表征发现,Cu与Ni之间存在明显的相互作用,改变了各自的还原性能;同时Cu的加人提高了Ni的分散程度;等离子体的引入减少了反应过程中积炭的形成,提高了反应稳定性.     

激光剥蚀电感耦合等离子体质谱法测定碳化硅器件中杂质元素

采用激光剥蚀电感耦合等离子体质谱法(LA-ICP-MS),以NIST玻璃标准物质制作校准曲线,29Si为内标,相对灵敏度因子(RSF)校准标样和样品间的基体效应,对碳化硅陶瓷器件中9种痕量元素(B,Ti,Cr,Mn,Fe和Ni等)进行定量测定。选择线性扫描方式,激光剥蚀孔径为150μm,氦气和氩气流量为0.7 L/min时,信号稳定性和灵敏度最佳。经内标校准后,各元素标准曲线的线性有较大改善,线性相关系数为0.9981~0.9999。以建立的方法对碳化硅标准参考物质(BAM-S003)中的痕量元素进行测定,并与标准参考值进行对比,结果一致,证实了LA-ICP-MS方法应用于碳化硅样品检测的准确性和有效性。采用本方法定量测定碳化硅器件中痕量元素,结果与辉光放电质谱法(GD-MS)测定的结果比较一致。元素B,Ti,Cr,Mn,Fe,Ni,Cu,Sr和La的检出限为0.004~0.08 mg/kg,相对标准偏差(RSD)小于5%。     

低温等离子体原子化器-原子荧光光谱法测定碲

基于介质阻挡放电(DBD)原理和结构,建立了适用于原子荧光光谱仪(AFS)的低温等离子体小型原子化器(Atomizer),并研究了氢化物发生-低温等离子体原子化器-原子荧光光谱(HG-DBDAtomizer-AFS)测定环境样品中痕量碲(Te)的分析方法。DBD等离子体原子化器具有小型、低温等优点。对DBD放电结构和放电功率、载气气体流速,氢化物发生过程中的酸度、KBH4浓度,以及观测高度等实验条件进行了详细的考察并优化。本系统测定Te的检出限(3σ)为0.08μg/L;线性范围为0.5～80μg/L;测定精密度为2.1%(n=7);加标回收率为90%～103%。对国家级标准样品(GBW07404,GBW07405,GBW07406)进行测定,测定结果与标准值一致,证明本方法准确可行。     

激光剥蚀-电感耦合等离子体质谱法测定纯钌中19种杂质元素

建立了激光剥蚀-电感耦合等离子-体质谱法(LA-ICP-MS)法测定纯钌中Mg、Al、Fe、Ni、Cu、Zn、Rb、Rh、Pd、Mo、Ag、Cd、Sn、Ba、Ir、Pt、Au、Pb和Si等19种杂质元素的分析方法。优化了仪器参数：给出了激光能量为60%,剥蚀孔径为110 μm,扫描速率为50 μm/s,脉冲频率为10Hz,载气流量为0.74L/min条件下,信号强度和稳定性最佳。由于钌标准样品难以获得,本文选择用纯钌粉样品,高温高压溶解后,采用ICP-MS定值所测元素（除硅外）。根据钌粉样品的ICP-MS定值结果确定了测定元素的相对灵敏度因子（RSF）,对归一法结果进行较正,提高了方法准确度。方法的检出限为：0.001~12.81μg/g,相对标准偏差(RSD)为：10%～30%。采用本方法测定纯钌中杂质元素,结果与ICP-MS测定的结果吻合。     

激光剥蚀-电感耦合等离子体质谱(ICP-MS)法测定纯钌中19种杂质元素

建立了激光剥蚀-电感耦合等离子体质谱(LA-ICP-MS)法测定纯钌中Mg、Al、Fe、Ni、Cu、Zn、Rb、Rh、Pd、Mo、Ag、Cd、Sn、Ba、Ir、Pt、Au、Pb和Si等19种杂质元素的分析方法。优化了仪器参数,给出了激光能量为60%,剥蚀孔径为110μm,扫描速率为50μm/s,脉冲频率为10 Hz,载气流量为0.74 L/min条件下,信号强度和稳定性最佳。由于钌标准样品难以获得,因此选择用纯钌粉样品,高温高压溶解后,采用ICP-MS法定值所测元素(除硅外)。根据钌粉样品的ICP-MS法定值结果确定了测定元素的相对灵敏度因子(RSF),采用相对灵敏度因子(RSF)对所测结果进行校正,方法准确、快速,检出限为0.007~12.8μg/g,相对标准偏差(RSD)为10%~30%。测定纯钌中杂质元素,结果与ICP-MS法测定的结果吻合。     

激光剥蚀电感耦合等离子体质谱法中生物样品的元素分馏效应研究

采用213 nm-纳秒激光剥蚀系统对生物基体样品的剥蚀颗粒进行研究,优化了激光剥蚀条件.在剥蚀能量为25%,束斑直径为200 μm,剥蚀速率为20 μm/s,频率为20 Hz,载气为700 mL He + 700 mL Ar时,信号强度及稳定性最佳.以31P为内标元素,最佳剥蚀条件下,考察了56个元素的相对分馏因子.结果表明,生物基体的剥蚀颗粒相较于NIST 610 玻璃标样更大,达到3 μm;生物基体中元素分馏效应相较于玻璃基体小,大多数元素的相对分馏因子达到1.0 ±0.1.探讨了生物基体中元素分馏机理,分析了生物基体相较于玻璃基体剥蚀颗粒大,而相对分馏因子未明显增大的原因.一方面可能是粒径3 μm的颗粒进入电感耦合等离子体后能原子化;另一方面,大的剥蚀颗粒的富集效应相对较小.进一步对分馏效应的影响因素进行研究,发现分馏效应与激光剥蚀能量、激光频率和扫描速率相关,并且与元素的氧化物沸点负相关,与氧化物键能和电离能正相关.     

电感耦合等离子体质谱法测定土壤中有效态微量元素

以NaNO3为提取剂,采用电感耦合等离子体质谱(ICP-MS)技术同时测定土壤中有效态Cu、Cd、Cr、Zn、Ni、Pb、Mn 7种微量元素.考察了基体效应以及质谱干扰等因素,引入Rh为内标元素有效地克服了基体效应所引起的测量偏差.方法的检出限为0.033～0.21 μg/L,样品加标回收率为92.1％～116.8％,相对标准偏差(RSD)小于6.07％.     

激光剥蚀-电感耦合等离子体-原子发射光谱/质谱法分析中国古代钾玻璃组分

利用激光剥蚀电感耦合等离子体原子发射光谱(LA-ICP-AES)和激光剥蚀电感耦合等离子体质谱(LA-ICP-MS)分析了一批中国古代钾玻璃。样品表面磨去100μm以上,并通过预剥蚀去除风化影响,设计剥蚀路径以消除元素分布不均匀影响。通过钙铝及其它微量元素将钾玻璃分成3个亚类,它们可能有不同的配方及制造中心;研究发现,钾玻璃着色剂类型多样化,有单质Cu,Mn2+,Cu2+,Co2+等;系统研究了钾玻璃的稀土元素特征,成功区分了九只岭地区及风门岭地区的钾玻璃;对两种方法在古代玻璃分析中的特点进行了探讨。     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.