分散聚合与水热处理相结合制备单分散聚苯乙烯微球的研究

将分散聚合与水热处理相结合,以聚乙烯醇为稳定剂,以乙醇和水为分散介质,三羟甲基丙烷三丙烯酸酯为交联剂,一步法成功制备得到不同粒径的单分散交联聚苯乙烯微球.以乙醇/水的比例为50/50的反应体系为基础,研究了聚乙烯醇类型和含量,有机相含量,引发剂浓度,以及水热釜填充量等对所制备的微球形貌的影响,发现聚乙烯醇类稳定剂的分子量的降低和含量的增多倾向于生成黏连的微球;在有交联剂的条件下,不含稳定剂的体系仍能够得到单分散的交联PS微球;有机相含量的增加会导致微球呈现多分散性;而体系中引发剂的含量和反应液在水热釜中的填充量对微球的形貌影响不大.进一步针对水热法的特点分析探讨了一步法成功制备单分散的交联聚苯乙烯微球的原因及其机理.     

反应原料组成对单分散苯乙烯微球粒径及其分布的影响

采用分散聚合工艺制备微米级单分散聚苯乙烯微球，并对分散聚合反应的内部影响因素(分散稳定剂、助稳定剂、单体、引发剂)进行了研究．结果表明，随着分散稳定剂和助稳定剂用量的增加，聚苯乙烯微球的粒径减小；随着单体和引发剂用量的增加，聚苯乙烯微球的粒径增大．分散稳定剂和单体用量是影响聚苯乙烯微球粒径分布的两个主要内部因素．     

室温沉淀聚合制备单分散聚苯乙烯微球

采用沉淀聚合的方法以乙醇/水为混合溶剂、K_2S_2O_8/NaHSO_3为引发剂,室温下引发苯乙烯聚合制备了单分散的聚苯乙烯(PS)微球.研究了反应时间、引发剂用量、反应溶剂中乙醇与水的比例、搅拌速度对聚苯乙烯微球的收率及形貌、单体转化率的影响.结果表明,聚苯乙烯微球的单体转化率、微球的收率和粒径随着反应时间的延长而增加,反应12 h后趋于稳定;当增加引发剂的用量,聚苯乙烯微球的单体转化率、微球的收率和粒径都有所增加,K_2S_2O_8与Na HSO_3用量分别在≤2.0%和1.3%时,能够得到单分散的聚苯乙烯微球;随着反应介质中水含量的增加,聚苯乙烯微球的单体转化率、微球的收率先增加后降低,单分散性变差,水含量在≤40%能够得到单分散的微球;搅拌速度从600 r/min增加到1200 r/min时,微球粒径、收率与单体转化率几乎没有变化.并初步研究了聚苯乙烯微球的形成机理.     

分散聚合法制备单分散交联聚苯乙烯微球

以苯乙烯为单体、二乙烯基苯为交联剂,通过优化反应条件,制备了平均粒径为3.28～9.04 μm的单分散聚苯乙烯微球和平均粒径为6.60 μm的单分散交联聚苯乙烯微球.探讨了单体浓度、引发剂含量、分散稳定剂用量对微球粒径和分散性的影响.热稳定性分析表明:交联聚苯乙烯微球耐热性明显优于线性聚苯乙烯.     

分散聚合法制备PVP微球的研究

以N-乙烯基吡咯烷酮(NVP)为初始单体,乙酸乙酯为分散介质,采用分散聚合法制备了分散性能良好、粒径为3～4μm的聚乙烯基吡咯烷酮(PVP)微球.考察了单体、分散剂及引发剂浓度对PVP微球的粒径、单体转化率及分子量的影响,并对PVP的结构和性能进行研究.结果表明,单体浓度增加,PVP微球粒径和分子量增大,单体转化率升高;分散剂浓度增加,PVP微球粒径变小,分子量增大,单体转化率升高;引发剂浓度增加,PVP微球粒径变大,分子量减小,单体转化率升高.与溶液聚合法相比,分散聚合法制备的PVP分子量较小且具有一定的结晶性.     

温度敏感型阳离子聚丙烯酰胺微球的制备及表征

以丙烯酰胺与甲基丙烯酰氧乙基三甲基氯化铵为单体,偶氮二异丁基脒二盐酸盐为引发剂,聚丙烯酰氧乙基三甲基氯化铵为稳定剂,在乙醇和水的混合介质中采用分散聚合的方法制备具有温度敏感性的阳离子型聚丙烯酰胺水分散微球。利用1HNMR和FTIR对共聚物的结构进行了表征,与此同时采用光学显微镜、TEM、激光粒度仪对聚合物微球的形貌、粒径等进行了系统研究。结果表明,随着醇水比的降低,微球的粒径逐渐减小,特性粘数逐渐增加;随着稳定剂浓度的增加,微球粒径逐渐减小。对阳离子型聚丙烯酰胺水分散微球的变温紫外研究结果表明,分散液具有明显的温敏性。随着温度在5～50℃范围内变化,分散液呈现从乳白色到透明状态的可逆变化。这是由于分散液微球的粒径随温度变化而发生可逆变化的结果。     

单分散聚苯乙烯微球的制备及影响因素研究

以聚乙烯吡咯烷酮为分散剂，无水乙醇为反应介质，偶氮二异丁腈为引发剂，采用分散聚合工艺，通过优化反应条件，制备出了粒径为5μm单分散（分散系数≤5％）聚苯乙烯微球。所制备的聚苯乙烯微球标准偏差δ＝0．16μm，分散系数ε＝0．02，且具有良好的球形度，表面非常光滑，无破损，无缺损。对影响单分散聚苯乙烯微球的因素进行了研究，结果表明：随着分散稳定剂用量的增加，聚苯乙烯微球的粒径减小；随着单体和引发剂用量的增加，聚苯乙烯微球的粒径增大。分散稳定剂和单体用量是影响聚苯乙烯微球粒径分布的两个主要因素。     

乙醇或乙醇-水为新的溶剂体系沉淀聚合制备单分散聚合物微球

以三羟甲基丙烷三丙烯酸酯(TMPTA)作交联剂,, 苯乙烯 (St) 作共聚单体,, 偶氮二异丁腈(AIBN)作引发剂,, 在低毒性乙醇和乙醇-水混合物这一新的溶剂体系中沉淀聚合反应4 h制备了单分散交联微球. 通过提高交联剂用量、引发剂用量和改变反应介质中水的用量探讨了提高单体转化率的方法. 结果表明,, 提高引发剂用量和增加溶剂中水的用量都能有效提高单体转化率并制得粒径均匀的微球. 保持其他条件不变,, 在乙醇中使用2 wt% AIBN仅能得到79%的单体转化率,, 提高AIBN用量至6 wt%或在介质中增加水的用量至28 vol%,, 在制得单分散微球的同时单体转化率可以达到95%以上. 文中对微球的形成机理和提高单体转化率的方法给出了理论解释.     

单分散PS/PAA聚合物微球的研制

以苯乙烯为单体,采用分散聚合法制备了单分散性的聚苯乙烯(PS)微球,然后以PS微球作为种子、丙烯酸(AA)进行无皂种子乳液聚合制备了PS／PAA微球。考察了单体、引发剂、分散剂用量,反应介质极性和交链剂等因素对微球粒径大小及其分布的影响,探讨了分散聚合的反应机理。结果表明,通过改变反应工艺条件,能够制备粒径为1．0～3．0μm、单分散性很好的PS微球;通过无皂种子乳液聚合得到的核壳结构的PS／PAA微球粒径为2．50μm,多分散系数(PI)为0．0325,酸值为10．27mgNaOH／g,其表面带有羧基的特性能进一步扩大应用范围。     

乙酸乙酯/乙醇混合溶液中分散聚合制备单分散亚微米级聚丙烯酰胺微球

以乙酸乙酯/乙醇混合溶液为分散介质, PVP为分散剂, 通过分散聚合法合成了单分散亚微米级PAM微球. 在反应初期, 自动加速现象明显. 由于凝胶效应的影响, 分子量随着单体转化率的提高而逐渐增大. 考察了分散剂浓度对最终产物增率的影响, 并用IR光谱对产物的结构进行了表征, 证明分散聚合体系中吸附稳定机理和接枝稳定机理同时存在, 且以后者为主. 同时还研究了混合溶剂比例、分散剂浓度、初始单体浓度和引发剂浓度对微球粒径及粒径分布的影响. 结果表明, 乙酸乙酯/乙醇体积比在5∶5-7∶3范围内, 可得到粒径在200 nm左右, 且分布较窄的PAM微球; 分散剂浓度增大, 粒径减小; 引发剂浓度增加, 粒径增大; 初始单体浓度较高或较低时, 都得不到单分散性微球.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.