ZnO-Si不同退火条件对生长ZnSe薄膜的影响

研究了作为缓冲层的ZnO薄膜在不同的退火时间、退火温度下退火对Si衬底上生长ZnSe膜质量的影响。当溅射有ZnO膜的Si(111)衬底的退火条件变化时，从X射线衍射谱（XRD）和光致发光谱（PL）中可见，ZnSe(111)膜的晶体质量有较大的变化。变温的PL谱表明，Si衬底上生长的具有ZnO缓冲层的ZnSe膜的近带边发射峰起源于自由激子发射。     

用等离子体辅助分子束外延生长氧化锌单晶薄膜

利用等离子体辅助分子束外延(P-MBE)方法,通过优化生长条件,在c平面蓝宝石(Al_2O_3)上生长出氧化锌(ZnO)单晶薄膜。使用反射式高能衍射仪(RHEED)原位监测到样品表面十分平整,X射线摇摆曲线(XRC)测得ZnO薄膜的<002>取向半峰全宽为0.20°,证实为ZnO单晶薄膜。室温下吸收谱(ABS)和光致发光(PL)谱显示了较强的激子吸收和发射,且无深能级(DL)发光。电学性能测量表明,生长的ZnO为n型半导体,室温下载流于浓度为7×10~(16) cm~(-3),与体单晶ZnO中的载流子浓度相当。     

热处理参数对溶胶-凝胶法制备氧化锌薄膜特性的影响

采用溶胶-凝胶旋涂法在Si(111)衬底上生长了ZnO薄膜，并用荧光光谱、原子力显微镜和XRD对ZnO薄膜样品进行了分析.结果表明，溶胶-凝胶旋涂法制备的ZnO薄膜为纤锌矿结构，其c轴取向程度与热处理温度有很大的关系.当热处理温度小于550℃时，氧化锌薄膜在室温下均有较强的紫外带边发射峰，而可见波段的发射很弱；当热处理温度高于550℃时，可见波段发射明显增强.对经过不同时间热处理的ZnO薄膜样品分析表明，氧化锌薄膜的荧光特性及表面形貌与热处理时间也有很大关系，时间过短可见波段的发射较强，但时间过长会导致晶 关键词： ZnO薄膜 光致发光     

Co与Cu掺杂ZnO薄膜的制备与光致发光研究

采用溶胶-凝胶旋涂法在玻璃衬底上制备了Co, Cu单掺杂及Co,Cu共掺杂ZnO薄膜.用金相显微镜观察了Co与Cu掺杂对ZnO薄膜形貌的影响.X射线衍射（XRD）研究揭示所有ZnO薄膜样品都存在（002）择优取向,在Cu单掺的ZnO薄膜中晶粒尺寸最大.对所有样品的室温光致发光测量都观察到较强的蓝光双峰发射和较弱的绿光发射,其中长波长的蓝光峰和绿光峰都能够通过掺杂进行控制.对不同掺杂源的ZnO薄膜发光性能进行了分析,认为蓝光峰来源于电子由导带底到锌空位能级的跃迁及锌填隙到价带顶的跃迁,绿光峰是由于掺杂造成的 关键词： ZnO薄膜 溶胶-凝胶 Co Cu掺杂 光致发光     

石英衬底上Au缓冲层对ZnO薄膜微结构的影响

采用单源化学气相沉积(SSCVD)法,在石英衬底上以Au为缓冲层,Zn4(OH)2(O2CCH3)6.2H2O为固相源制备ZnO薄膜。SEM和XRD测试ZnO薄膜的微结构,结果表明:相对于SiO2衬底上生长的ZnO薄膜,Au/SiO2衬底上生长的ZnO薄膜具有较好的结晶质量和表面平整度;对制备ZnO薄膜的衬底温度进行了工艺优化,结果表明:500℃时制备的ZnO薄膜颗粒大小均匀,结晶质量较好;通过荧光光谱仪对Au/SiO2衬底上的ZnO薄膜进行光致发光(PL)谱测试,ZnO薄膜在400nm出现紫光发射峰,而没有出现与缺陷相关的深能级发射峰,表明ZnO薄膜具有较好的结晶质量。     

ZnO薄膜的制备和发光特性的研究

用射频磁控溅射的方法在石英衬底上沉积了氧化锌薄膜，在室温下测量了样品的XRD曲线、吸收光谱以及光致发光光谱。探讨了气氛中氧气与氩气比对制备薄膜的影响，从XRD谱中可以看出，样品具有较好的结晶状态。另外，样品在紫外有较强的吸收，而其光致发光也是较强的紫外发射，这表明带间跃迁占了主导地位，以上结果说明：用溅射方法制备的ZnO薄膜结晶质量较好，富锌状态有所改善。     

Na-Mg共掺杂ZnO薄膜的结构和光学性质

利用溶胶-凝胶法,在普通载玻片上使用旋转涂膜技术制备了具有c轴择优取向生长的Na-Mg共掺杂的ZnO薄膜。用XRD、SEM、光致发光(PL)及透射光谱对薄膜样品进行了表征。结果表明:Na-Mg共掺杂有利于ZnO薄膜的c轴择优取向生长,并且随着Na+掺杂浓度的增加,晶粒尺寸先增大后减小;通过比较不同掺杂浓度ZnO薄膜的PL谱,推测发光峰值位于380nm的紫外发射与ZnO的自由激子复合有关;发现掺入Mg的确能使ZnO禁带宽度增大,掺杂组分为Na0.04Mg0.2Zn0.76O时,其PL谱只有一个很强的紫光发射峰,其近带边紫外光发射强度较未掺杂的ZnO增强了近10倍,极大地提高了薄膜紫外发光性能;并且随Na+浓度增加薄膜透光性减弱。     

MOCVD方法生长的氧化锌薄膜及其发光特性

近年来,随着近紫外光发射氧化锌薄膜研究的进展,许多先进的薄膜生长手段被广泛采用。本文探索了用MOCVD方法在硅衬底上生长氧化锌薄膜的方法,试验了用几种不同的有机金属源生长ZnO薄膜;研究了源材料及生长压力和温度对薄膜生长的影响;观察了样品的室温光致发光光 谱。通过与溅射方法生长的ZnO薄膜的比较,提出了影响材料结构和发光特性的可能原因。     

Cu掺杂氧化锌薄膜的发光特性研究

通过射频反应溅射法在Si（111）衬底上制备了不同Cu掺杂量的ZnO薄膜.室温下测量了样品的光致发光（PL）谱，所有样品的PL谱中均观察到435?nm左右的蓝光发光带，该发光带的强度与Cu掺杂量和溅射功率有关.当溅射功率为150?W，Cu掺杂量为2.5%时，ZnO薄膜的PL谱中出现了较强的蓝光双峰，而溅射功率为100?W，Cu掺杂量为1.5%时，出现了位于437nm（2.84eV）处较强的蓝光峰，后者的取向性较好.还研究了掺杂量和溅射功率对发光特性的影响，并对样品的蓝光发光机制进行了探讨. 关键词： ZnO薄膜 Cu掺杂 光致发光谱 射频反应共溅射     

溶胶-凝胶法纳米ZnO薄膜的绿光发射

利用溶胶-凝胶法制备了纳米ZnO薄膜,室温下测量了样品的光致发光谱(PL)和X射线衍射谱(XRD),观测到中心波长在523 nm附近的绿色荧光发射,研究了纳米ZnO薄膜的绿光发射机制,证实了纳米ZnO薄膜绿光可见发射带来自氧空位(Vo)形成的浅施主能级和锌空位(Vzn)形成的浅受主能级之间的复合。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.