CaCu3Ti4O12陶瓷的介电特性与弛豫机理

本文采用Novocontrol宽频介电谱仪在-100 ℃–100 ℃温 度范围内、0.1 Hz–10 MHz频率范围内测量了表面层打磨前 后CaCu₃Ti₄O₁₂陶瓷的介电特性, 分析了CaCu₃Ti₄O₁₂陶瓷的介电弛豫机理. 首先, 基于对宏观“壳-心”结构的定量分析, 排除了巨介电常数起源于表面层效应的可能性; 其次, 基于经典Maxwell-Wagner夹层极化及其活化能物理本质的分析, 排除了巨介电常数起源于经典Maxwell-Wagner极化的可能性; 最后, 依据晶界Schottky势垒与本征点缺陷的本质联系, 提出了巨介电常数起源于Schottky势垒边界陷阱电子弛豫的新机理. 陷阱电子弛豫机理反映了CaCu₃Ti₄O₁₂陶瓷本征点缺陷、 电导、介电常数之间的本质关系. 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 介电弛豫 Schottky势垒 点缺陷     

直流老化对CaCu3Ti4O12陶瓷介电性能的影响

在电场为3.5 kV/cm的条件下, 对CaCu₃Ti₄O₁₂陶瓷进行了60 h的直流老化, 研究了老化过程对CaCu₃Ti₄O₁₂陶瓷介电性能和电气特性的影响. J-E特性测试结果表明, 直流老化导致CaCu₃Ti₄O₁₂陶瓷击穿场强、非线性系数和势垒高度明显降低. 介电性能测试结果表明, 低频介电常数和介电损耗明显增大, 并且介电损耗随频率的变化遵从Debye弛豫理论, 可分解为直流电导损耗和弛豫损耗, 直流老化主要导致了电导损耗的增加. 在低温233 K, 介电损耗谱中出现两个弛豫峰, 其活化能分别为0.10, 0.50 eV, 认为对应着晶粒和畴界的弛豫过程, 且不随直流老化而变化. 通过电模量谱对CaCu₃Ti₄O₁₂陶瓷的弛豫过程进行了表征, 发现直流老化导致的界面空间电荷在外施交变电场的作用下符合Maxwell-Wagner极化效应, 并在低频区形成新的弛豫峰. 在高温323-473 K的阻抗谱中, 晶界弛豫峰在直流老化后明显向高频移动, 其对应的活化能从1.23 eV 下降到0.72 eV, 晶界阻抗值下降了约两个数量级. 最后, 建立了CaCu₃Ti₄O₁₂陶瓷的阻容电路模型, 分析了介电弛豫过程与电性能之间的关联.     

Fe掺杂CaCu3Ti4O12陶瓷的介电性能与弛豫特性研究

采用固相反应法制备了CaCu₃Ti_4-xFe_xO₁₂(0≤x≤0.2)陶瓷,通过X射线衍射、扫描电子显微镜、介电频谱和阻抗谱等手段研究了Fe对CaCu₃Ti₄O₁₂陶瓷的结构和介电性能的影响.研究发现：CaCu₃Ti_4-xFe_{x关键词： 巨介电常数 双阻挡层电容模型 界面极化}     

CaCu3Ti4O12陶瓷的微观结构和电学性能

利用传统的固相反应工艺，在不同的烧结温度下制备了一系列的CaCu₃Ti₄O₁₂陶瓷样品，考察了其微观结构以及介电和复阻抗方面的电学性质.研究发现这些样品在微观结构方面可分为三种类型，高介电性与微观结构有着密切的关联性.室温下，样品的低频介电常数随陶瓷晶粒尺寸的增大而提高.随着测试温度的升高，不同微观结构类型的样品呈现出不同的电学性质的变化，但其中也存在着一些相同的特征.高温下，介电频谱呈现出一个低频介电响应和两个类Debye型弛豫色散，复阻抗谱呈现出三个Cole-Cole半圆弧.将实验上观测到的电学性质的起因归于陶瓷多晶微结构中的晶畴、晶界和晶粒内的缺陷. 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 微观结构 电学性质     

添加Nb对CaCu3Ti4O12陶瓷介电性能的影响

采用固相反应法制备了CaCu₃Ti_4-xNb_xO₁₂(x=0，0.01，0.04，0.08，0.2)陶瓷，样品在x取值范围内形成了连续固溶体.在40Hz—110MHz频率范围对样品进行了介电频谱分析，实验结果表明，与纯CaCu₃Ti₄O₁₂不同，含Nb试样除了在频率大于10kHz范围内出现的德拜弛豫 关键词： 巨介电常数 德拜弛豫 阻挡层电容 等效电路     

CaCu3Ti4O12块材和薄膜的巨介电常数

用固相反应法和脉冲激光沉积(PLD)制备了CaCu₃Ti₄O₁₂块材和薄膜，获得了相对介电常数ε′（1kHz,300K)高于14000的介电特性，是目前该体系最好的结果.报道了(00l)取向高质量CaCu₃Ti₄O₁₂外延薄膜及其介电性质.C aCu₃Ti₄O₁₂相对介电常数ε′在100—300K温度范围 内 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 巨介电常数 PLD     

CaCu3Ti4O12陶瓷的微观结构及直流导电特性

采用传统固相反应法制备了CaCu₃Ti₄O₁₂陶瓷.XRD证实其CaCu₃Ti₄O₁₂相;SEM观察到明显的晶粒晶界结构,晶界区亦由小晶粒构成;结合EDS结果,判定晶界区小晶粒为CuO.在较宽的温度范围内,CaCu₃Ti₄O₁₂陶瓷的介电常数保持在10⁵左右;当频率为10³ Hz温度小于150 K时,介电常数迅速下降.在173—373 K温度范围内,通过其I-V特性,得到CaCu₃Ti₄O₁₂陶瓷直流电导随温度的变化：直流电导与温度的关系可分为三部分,对应的活化能分别为0.681 eV,0.155 eV和0.009 eV,这与CuO陶瓷直流电导活化能一致.可以认为晶界区的CuO小晶粒在CaCu₃Ti₄O₁₂陶瓷的直流电导中占主导,这为解释CaCu₃Ti₄O₁₂陶瓷反常的介电性能提供了新的思路. 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 微观结构 直流电导 介电特性     

La掺杂SrBi4Ti4O15铁电材料性能研究

按x=0.00，0.10，0.25，0.50，0.75和1.00，采用固相烧结工艺，制备了不同La掺杂量的SrBi_4-xLa_xTi₄O₁₅的陶瓷样品. 用x射线衍射对其微结构进行了分析，并测量了铁电、介电性能.结果发现，La掺杂未改变SrBi₄Ti ₄O₁₅的晶体结构.随掺杂量的增加，样品的矫顽场(E_c)下降，剩余极化(2P_{关键词： 4-x}La_xTi₄O₁₅')" href="#">SrBi_4-xLa_xTi₄O₁₅ La掺杂 铁电性能 相变温度 弛豫铁电     

Al2O3-Y2O3-ZrO2三相复合陶瓷的介电谱研究

采用传统的固相反应法,在1400–1500 ℃下烧结,制备得到Al₂O₃-Y₂O₃-ZrO₂三相复合陶瓷.样品的结构、形貌和电性能分别用X射线衍射(XRD)、扫描电子显微镜(SEM)及介电谱表征.XRD表明此三相复合体系无其他杂相,加入Y₂O₃及ZrO₂后使得Al₂O₃成瓷温度降低;SEM表明此体系晶粒直径为200–500 nm,并且样品随烧结温度的升高而变得更加致密,晶界更加清晰;介电损耗谱中出现峰值弛豫现象,根据Cole-Cole复阻抗谱得出其为非德拜弛豫. 关键词： 2O₃-Y₂O₃-ZrO₂三相陶瓷')" href="#">Al₂O₃-Y₂O₃-ZrO₂三相陶瓷 介电弛豫 阻抗谱 热导率     

(Na1/2Bi1/2)Cu3Ti4O12陶瓷的微观结构和电学性质

利用固相反应法在不同烧结温度条件下制备了一系列(Na_1/2Bi_1/2)Cu₃Ti₄O₁₂(NBCTO)陶瓷样品,研究了它们的晶体结构、微观组织结构、介电性质和复阻抗及其随温度的变化. 实验发现NBCTO陶瓷所呈现出的电学性质与CaCu₃Ti₄O₁₂陶瓷相应的电学性质非常类似. 烧结温度为990℃至1060℃范围的NBCTO陶瓷样品室 关键词： 高介电材料 介电性质 复阻抗 内阻挡层电容     

氧含量对CaCu3Ti4O12巨介电常数和介电过程的影响

本文研究了在真空、空气和氧气中烧结制备的三种 CaCu₃Ti₄O₁₂陶瓷材料的介电特性. 交流阻抗测量结果表明在10—300 K温度范围, 三种样品的介电温谱中均出现三个平台, 其电阻实部和电容虚部在相应温度出现损耗峰, 真空条件烧结的样品具有较高的介电平台和较明显的电阻实部与电容虚部峰值, 表明氧含量和氧空位对CaCu₃Ti₄O₁₂的介电性质具有重要影响, 介电温谱出现的三个平台分别源于晶粒、晶界及氧空位陷阱.温谱分析表明晶粒的激活能与烧结气氛有较大关系,氧空位引起的电子短程跳跃及跳跃产生的极化子是晶粒电导和电容的主要起源.氧空位陷阱的激活能基本与烧结气氛无关,约为0.46 eV. 氧空位对载流子的陷阱作用是CaCu₃Ti₄O₁₂ 低频高介电常数的重要起源.     

Dielectric property of CaCu3Ti4O12 thin film grown on Nb-doped SrTiO3(100) single crystal

Thin film of CaCu₃Ti₄O₁₂ (CCTO) has been deposited on Nb-doped SrTiO₃(100) single crystal using pulsed laser deposition. The dielectric constant and AC conductivity of CCTO film in the metal–insulator–metal capacitor configuration over a wide temperature (80 to 500 K) and frequency (100 Hz to 1 MHz) range have been measured. The small dielectric dispersion with frequency observed in the lower temperature region (<300 K) indicates the presence of small defects in the deposited CCTO thin film. The frequency-dependent AC conductivity at lower temperature indicates the hopping conduction. The dielectric dispersion data has been analyzed in the light of both conductivity relaxation and Debye type relaxation with a distribution of relaxation times. Origin of dielectric dispersion is attributed to the distribution of barrier heights such that some charge carriers are confined between long-range potential wells associated with defects and give rise to dipolar polarization, while those carriers which do not encounter long-range potential well give rise to DC conductivity.     

Bi0.5Ba0.5Fe0.5Ti0.49Nb0.01O3热敏陶瓷的微结构和电学性能研究

采用固相合成工艺,制备了Bi_05Ba_05Fe_05Ti_049Nb_001O₃（BBFTN）热敏陶瓷,借助X射线衍射仪、扫描电子显微镜、阻温测试仪和交流阻抗谱考察其微结构、直流电阻、介电特性、阻抗和电学模量方面的电学性能. 结果表明：BBFTN材料依然为立方钙钛矿结构,平均晶粒尺寸约为10 μm,晶格常数相对于BaTiO₃的晶格常数有所变大;室温电 关键词： 05Ba_05Fe_05Ti_049Nb_001O₃')" href="#">Bi_05Ba_05Fe_05Ti_049Nb_001O₃ 微结构 电学性能     

等静压下0.75Pb（Mg1/3Nb2/3）O3-0.25PbTiO3陶瓷的介电性能研究

研究了等静压对0.75Pb（Mg_1/3Nb_2/3）O₃-0.25PbTiO₃（PMN-25PT）陶瓷介电温谱的影响,PMN-25PT剩余极化随等静压变化和等静压压致相变.结果表明,随着压力增加,PMN-25PT的介电峰值温度T_m降低,/+{dT_m}/-{dP}≈-4℃/kbar,极化弛豫增强;剩余极化随压力增加连续减小;介电常数对压力的依赖关系与对温度场的依赖相似,压力诱导PMN-25PT发生弛豫铁电—顺电相变,相变为宽化的渐变过程,频率色散和极化弛豫更加强烈和普遍. 关键词： 铌镁酸铅-钛酸铅 等静压 介电弛豫 压致相变     

Pb(Zr,Sn,Ti)O3反铁电陶瓷的低温相变扩散与极化弛豫

用弱场介电温谱、热释电流谱、强场电滞回线和变温X射线衍射谱研究了微量La掺杂Pb(Zr,Sn,Ti)O₃(PZST)反铁电(AFEt)陶瓷在-100—180℃温区内的结构与电学特性.弱场介电温谱显示,AFEt陶瓷在低温段(-100—50℃)呈现介电频率弥散(0.1—100kHz)和扩散型相变的特征,而变温X射线衍射谱却表明材料在这一温区内保持四方相结构;低温下经强场作用后,AFEt被诱导为亚稳三方铁电态,介电频率弥散消失.基于多元复杂化合物的组分起伏理论,讨论了PZST AFEt陶瓷 关键词： Pb(Zr Sn 3反铁电陶瓷')" href="#">Ti)O₃反铁电陶瓷 反铁电弛豫 相变 变温X射线衍射     

Effect of phase transformation on optical and dielectric properties of zirconium oxide nanoparticles

Zirconium oxide nanoparticle (ZrO₂) is synthesized by the hydrothermal method at different calcination temperatures. The structural analysis is carried out by X-ray diffraction and Raman spectra. The sample prepared at 400 °C and 1100 °C showed the cubic and monoclinic phase, respectively, and the sample calcined at 600 °C and 800 °C showed the mixed phase with co-existence of cubic and monoclinic phases. Furthermore, the morphology and particle size of these samples were investigated by scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis. The band gap estimated from UV–Vis spectra of ZrO₂ (zirconia) nanocrystalline materials calcined at different temperatures from 400 °C to 1100 °C was in the range of 2.6–4.2 eV. The frequency dependence of dielectric constant and dielectric loss was investigated at room temperature. The low frequency region of dielectric constant is attributed to space charge effects.     

Influence of Lu2O3 on electrical and microstructural properties of CaCu3Ti4O12 ceramics

In this work, the influence of Lu₂O₃ doped on the dielectric and electrical properties of CaCu₃Ti₄O₁₂ was reported. Lu₂O₃-doped CCTO was prepared by a conventional solid state technique using CuO, TiO₂, and CaCO₃ as starting materials. The samples were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM); dielectric measurements were measured in the 10² Hz–10⁷ Hz frequency range at room temperature; and the nonlinear behavior of all samples was measured. The doping of Lu₂O₃ resulted in an increase in the dielectric constant of CCTO, but decreased the stability of the frequency dependence. Increasing concentrations of Lu₂O₃ resulted in decreasing nonlinear coefficients.     

Influence of sintering conditions and doping on the dielectric relaxation originating from the surface layer effects in CaCu3Ti4O12 ceramics

Detailed investigations into the dielectric dispersion phenomenon in the giant dielectric constant material CaCu₃Ti₄O₁₂ (CCTO) around room temperature revealed the existence of two successive dielectric relaxations. In the temperature domain, a new dielectric relaxation was clearly observed around 250 K, in addition to the well-investigated dielectric relaxation close to 100 K. The effect of sintering and doping (La³⁺) on the strength of these dielectric relaxations were studied in detail. The sintering temperature as well as its duration was found to have tremendous influence on the dielectric relaxation that was encountered around 250 K. This Maxwell-Wagner (M-W) type of relaxation was found to be originating from the surface layer containing the Cu-rich phase, which was ascribed to the difference in the oxygen content between the surface and the interior of the sample. Interestingly, this particular additional relaxation was not observed in La_2/3Cu₃Ti₄O₁₂, a low dielectric constant member of the CCTO family, in which the segregation of Cu-rich phase on the surface was absent. Indeed the correlation between the new relaxation and the presence of Cu-rich phase in CCTO ceramics was further corroborated by the absence of the same after removing the top and bottom layers.