Er3+掺杂SiO2复合的Al2O3粉末结构及光致发光特性

采用溶胶-凝胶(sol-gel)工艺制备0.1 mol% Er³⁺掺杂Al₂O₃体系和SiO₂-Al₂O₃复合体系粉末. 实验结果表明：5 mol%的SiO₂复合加入Al₂O₃抑制γ→θ和θ→α相转变. 掺0.1 mol%Er³⁺:Al₂O₃体系粉末，900℃烧结，在1.47—1.63μm波段内光致发光(PL)谱为中心波长1.53 μm、半高宽56 nm的单一宽峰，1000—1200℃烧结，劈裂为多峰PL谱. 掺0.1 mol%Er³⁺:SiO₂-Al₂O₃复合体系粉末，在高达1200℃烧结，仍保持中心波长1.53 μm的单一宽峰PL谱，由于—OH更完全的脱除，PL强度较900℃烧结Al₂O₃体系，SiO₂-Al₂O₃复合体系均提高1个数量级. 关键词： 2-Al₂O₃复合体系')" href="#">SiO₂-Al₂O₃复合体系 掺铒 溶胶-凝胶工艺 光致发光     

CaCu3Ti4O12陶瓷的微观结构和电学性能

利用传统的固相反应工艺，在不同的烧结温度下制备了一系列的CaCu₃Ti₄O₁₂陶瓷样品，考察了其微观结构以及介电和复阻抗方面的电学性质.研究发现这些样品在微观结构方面可分为三种类型，高介电性与微观结构有着密切的关联性.室温下，样品的低频介电常数随陶瓷晶粒尺寸的增大而提高.随着测试温度的升高，不同微观结构类型的样品呈现出不同的电学性质的变化，但其中也存在着一些相同的特征.高温下，介电频谱呈现出一个低频介电响应和两个类Debye型弛豫色散，复阻抗谱呈现出三个Cole-Cole半圆弧.将实验上观测到的电学性质的起因归于陶瓷多晶微结构中的晶畴、晶界和晶粒内的缺陷. 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 微观结构 电学性质     

CaCu3Ti4O12陶瓷的介电特性与弛豫机理

本文采用Novocontrol宽频介电谱仪在-100 ℃–100 ℃温 度范围内、0.1 Hz–10 MHz频率范围内测量了表面层打磨前 后CaCu₃Ti₄O₁₂陶瓷的介电特性, 分析了CaCu₃Ti₄O₁₂陶瓷的介电弛豫机理. 首先, 基于对宏观“壳-心”结构的定量分析, 排除了巨介电常数起源于表面层效应的可能性; 其次, 基于经典Maxwell-Wagner夹层极化及其活化能物理本质的分析, 排除了巨介电常数起源于经典Maxwell-Wagner极化的可能性; 最后, 依据晶界Schottky势垒与本征点缺陷的本质联系, 提出了巨介电常数起源于Schottky势垒边界陷阱电子弛豫的新机理. 陷阱电子弛豫机理反映了CaCu₃Ti₄O₁₂陶瓷本征点缺陷、 电导、介电常数之间的本质关系. 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 介电弛豫 Schottky势垒 点缺陷     

巨介电常数氧化物CaCu3Ti4O12的介电和阻抗特性

采用固相烧结法合成了单相巨介电常数氧化物CaCu₃Ti₄O₁₂（CCTO）.用阻抗分析仪分析了10—420 K温度范围内的介电频谱和阻抗谱特性,并结合ZVIEW软件进行了模拟.结果表明：温度高于室温时,频谱出现两个明显的弛豫台阶,低频弛豫介电常数随温度升高而显著增大,表现出热离子极化特点;温度低于室温时,频谱表现出类德拜弛豫,且高、低平台介电常数值基本不随温度变化,表现出界面极化特点和较好的温度稳定性.频谱中依次出现的介电弛豫对应于阻抗谱中 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 介电频谱 阻抗谱 Cole-Cole半圆弧     

12CaO·7Al2O3/5CaO·3Al2O3：Sm3+新型红色荧光粉的制备及发光性质

采用自蔓延燃烧法制备了不同Sm³⁺掺杂浓度的12CaO·7Al₂O₃（C12A7：x%Sm³⁺）荧光粉。在404 nm近紫外光激发下,观察到了位于565,599,648 nm附近的3个光发射峰,分别归属于Sm³⁺的⁴G_5/2→⁶H_J/2（J=5,7,9）能级跃迁。随着Sm³⁺掺杂浓度增加,红光发射强度呈现了先增大后减小的规律,优化的Sm³⁺掺杂摩尔分数为1.5%,发光的浓度猝灭效应可归因于Sm³⁺之间发生了交叉弛豫过程。采取混相策略,通过降低初始粉体的煅烧温度至900℃获得了12CaO·7Al₂O₃/5CaO·3Al₂O₃：1.5%Sm³⁺（C12A7/C5A3：Sm³⁺）混相荧光粉,进一步提高了红光发射强度。利用变温光致发光谱计算得到混相样品的热激活能约为200 meV,结果表明该混相荧光粉具有良好的热稳定性。     

MoO3/Al2O3催化剂中Mo分散的正电子研究

用浸渍法制备了一系列不同Mo含量的MoO₃/Al₂O₃催化剂.测量了这些样品的正电子湮没寿命谱(PALS)与符合多普勒展宽(CDB)谱,以研究其孔洞结构以及Mo分散.正电子寿命测量结果表明,Al₂O₃载体中存在两种不同尺寸的孔洞.掺入MoO₃之后,Mo原子主要进入Al₂O₃的大孔中,使孔洞体积减小.符合多普勒展宽谱结果表明,当MoO 关键词： 3/Al₂O₃催化剂')" href="#">MoO₃/Al₂O₃催化剂 正电子湮没寿命谱 符合多普勒展宽 Mo 分散     

直流老化对CaCu3Ti4O12陶瓷介电性能的影响

在电场为3.5 kV/cm的条件下, 对CaCu₃Ti₄O₁₂陶瓷进行了60 h的直流老化, 研究了老化过程对CaCu₃Ti₄O₁₂陶瓷介电性能和电气特性的影响. J-E特性测试结果表明, 直流老化导致CaCu₃Ti₄O₁₂陶瓷击穿场强、非线性系数和势垒高度明显降低. 介电性能测试结果表明, 低频介电常数和介电损耗明显增大, 并且介电损耗随频率的变化遵从Debye弛豫理论, 可分解为直流电导损耗和弛豫损耗, 直流老化主要导致了电导损耗的增加. 在低温233 K, 介电损耗谱中出现两个弛豫峰, 其活化能分别为0.10, 0.50 eV, 认为对应着晶粒和畴界的弛豫过程, 且不随直流老化而变化. 通过电模量谱对CaCu₃Ti₄O₁₂陶瓷的弛豫过程进行了表征, 发现直流老化导致的界面空间电荷在外施交变电场的作用下符合Maxwell-Wagner极化效应, 并在低频区形成新的弛豫峰. 在高温323-473 K的阻抗谱中, 晶界弛豫峰在直流老化后明显向高频移动, 其对应的活化能从1.23 eV 下降到0.72 eV, 晶界阻抗值下降了约两个数量级. 最后, 建立了CaCu₃Ti₄O₁₂陶瓷的阻容电路模型, 分析了介电弛豫过程与电性能之间的关联.     

Cr4+在Al2O3多晶体中的光谱性能研究

采用传统无压烧结工艺制备Cr:Al₂O₃透明多晶陶瓷.测定了其退火前后的吸收光谱和荧光光谱，发现在Al₂O₃六配位的八面体结构中，Cr⁴⁺的荧光发射也处在1100—1600nm波段的红外区间，荧光发射峰位于1223nm附近，类似Cr⁴⁺在四面体中的发光行为.同时由于氧化铝晶格常数较小，晶体场强较强，使Cr⁴⁺:Al₂O_{3< 关键词： 4+')" href="#">Cr⁴⁺ 2}O₃透明陶瓷')" href="#">Cr:Al₂O₃透明陶瓷 光谱性质 八面体     

CaCu3Ti4O12陶瓷的微观结构及直流导电特性

采用传统固相反应法制备了CaCu₃Ti₄O₁₂陶瓷.XRD证实其CaCu₃Ti₄O₁₂相;SEM观察到明显的晶粒晶界结构,晶界区亦由小晶粒构成;结合EDS结果,判定晶界区小晶粒为CuO.在较宽的温度范围内,CaCu₃Ti₄O₁₂陶瓷的介电常数保持在10⁵左右;当频率为10³ Hz温度小于150 K时,介电常数迅速下降.在173—373 K温度范围内,通过其I-V特性,得到CaCu₃Ti₄O₁₂陶瓷直流电导随温度的变化：直流电导与温度的关系可分为三部分,对应的活化能分别为0.681 eV,0.155 eV和0.009 eV,这与CuO陶瓷直流电导活化能一致.可以认为晶界区的CuO小晶粒在CaCu₃Ti₄O₁₂陶瓷的直流电导中占主导,这为解释CaCu₃Ti₄O₁₂陶瓷反常的介电性能提供了新的思路. 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 微观结构 直流电导 介电特性     

(Na1/2Bi1/2)Cu3Ti4O12陶瓷的微观结构和电学性质

利用固相反应法在不同烧结温度条件下制备了一系列(Na_1/2Bi_1/2)Cu₃Ti₄O₁₂(NBCTO)陶瓷样品,研究了它们的晶体结构、微观组织结构、介电性质和复阻抗及其随温度的变化. 实验发现NBCTO陶瓷所呈现出的电学性质与CaCu₃Ti₄O₁₂陶瓷相应的电学性质非常类似. 烧结温度为990℃至1060℃范围的NBCTO陶瓷样品室 关键词： 高介电材料 介电性质 复阻抗 内阻挡层电容     

Effects of RE2O3 (RE = Tm, Sc, Yb) addition on the superconducting properties of ErBa2Cu3Oy

We investigated the effects of added Tm₂O₃, Sc₂O₃, and Yb₂O₃ on the superconducting properties of sintered Er123 samples. Tm₂O₃ addition caused the least T_c degradation, exhibiting a T_c above 90 K even for 17 vol% addition. Samples with added Sc₂O₃ maintained a T_c at above 90 K up to an addition of 7.2 vol%, while Yb₂O₃-containing samples showed a monotonic decrease in T_c with increased vol% of added Yb₂O₃. Tm₂O₃-containing samples exhibited a slight increase in J_c(0.1 T)/J_c(0) and had constant J_c values even for 17 vol% addition. XRD and SEM results indicate that the Tm₂O₃ is very stable in the superconducting matrix.     

氧含量对CaCu3Ti4O12巨介电常数和介电过程的影响

本文研究了在真空、空气和氧气中烧结制备的三种 CaCu₃Ti₄O₁₂陶瓷材料的介电特性. 交流阻抗测量结果表明在10—300 K温度范围, 三种样品的介电温谱中均出现三个平台, 其电阻实部和电容虚部在相应温度出现损耗峰, 真空条件烧结的样品具有较高的介电平台和较明显的电阻实部与电容虚部峰值, 表明氧含量和氧空位对CaCu₃Ti₄O₁₂的介电性质具有重要影响, 介电温谱出现的三个平台分别源于晶粒、晶界及氧空位陷阱.温谱分析表明晶粒的激活能与烧结气氛有较大关系,氧空位引起的电子短程跳跃及跳跃产生的极化子是晶粒电导和电容的主要起源.氧空位陷阱的激活能基本与烧结气氛无关,约为0.46 eV. 氧空位对载流子的陷阱作用是CaCu₃Ti₄O₁₂ 低频高介电常数的重要起源.     

The electrical properties of dielectric stacks of SiO2 and Al2O3 prepared by atomic layer deposition method

We produced dielectric stacks composed of ALD SiO₂ and ALD Al₂O₃, such as SiO₂/Al₂O₃, Al₂O₃/SiO₂, and SiO₂/Al₂O₃/SiO₂, and measured the leakage currents through the stacks in comparison with those of the single oxide layers. SiO₂/Al₂O₃ shows lowest leakage current for negative bias region below 6.4 V, and Al₂O₃/SiO₂ showed highest current under negative biases below 4.5 V. Two distinct electron conduction regimes are observed for Al₂O₃ and SiO₂/Al₂O₃. Poole-Frenkel emission is dominant at the high-voltage regime for both dielectrics, whereas the direct tunneling through the dielectric is dominant at the low-voltage regime. The calculated transition voltage between two regimes for SiO₂ (6.5 nm)/Al₂O₃ (12.6 nm) is −6.4 V, which agrees well with the experimental observation (−6.1 V). For the same EOT of entire dielectric stack, the transition voltage between two regimes decreases with thinner SiO₂ layer.     

Influence of Lu2O3 on electrical and microstructural properties of CaCu3Ti4O12 ceramics

In this work, the influence of Lu₂O₃ doped on the dielectric and electrical properties of CaCu₃Ti₄O₁₂ was reported. Lu₂O₃-doped CCTO was prepared by a conventional solid state technique using CuO, TiO₂, and CaCO₃ as starting materials. The samples were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM); dielectric measurements were measured in the 10² Hz–10⁷ Hz frequency range at room temperature; and the nonlinear behavior of all samples was measured. The doping of Lu₂O₃ resulted in an increase in the dielectric constant of CCTO, but decreased the stability of the frequency dependence. Increasing concentrations of Lu₂O₃ resulted in decreasing nonlinear coefficients.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Dielectric and impedance measurements on (1−x)Ba(Fe1/2Ta1/2)O3-xBa(Zn1/3Ta2/3)O3 ceramics

In this work, ((1−x)Ba(Fe_1/2Ta_1/2)O₃-xBa(Zn_1/3Ta_2/3)O₃), ((1−x)BFT-xBZT) ceramics with x = 0.00–0.12 were synthesized by the solid–state reaction method. X-ray diffraction data revealed that both the powders and ceramics were of a pure-phase cubic perovskite structure. All ceramics showed large dielectric constants. For the x = 0.12 sample, a very high dielectric constant (>20,600) was observed. A lowering in the dielectric loss compared to pure BFT ceramics was observed with the BZT addition. The impedance measurements indicated that BZT has a strong effect on the bulk grain and grain boundary resistance of BFT ceramics. These results are in agreement with the measured dielectric properties. Based on dielectric and impedance results, (1−x)BFT-xBZT ceramics could be of great interest for high performance dielectric materials applications due their giant dielectric constant behavior.     

Investigation on densification of Al2O3/B4C ceramic by ab initio calculation and experiment

Compared to experiment, the adsorption energies, bonding properties, and electronic structure of two different Al₂O₃/B₄C bridge sites with seven different Al₂O₃ surfaces are investigated by ab initio periodic density functional theory. The Al₂O₃/B₄C ceramic sintered in Ar is synthesized and measured by XRD and TEM. The calculated results reveal that the densification of O_bridge site of Al₂O₃/B₄C surface is better than that of Al_bridge. The Al₂O₃ (1 1 3)/B₄C with O_bridge is the most favorable and stable. The electronic structure shows that the electron hybridization exists between Al, O atoms and C, B atoms. The results indicate that the calculated results are in good agreement with the experiment.     

The improvement of Al2O3/AlGaN/GaN MISHEMT performance by N2 plasma pretreatment

This paper discusses the effect of N 2 plasma treatment before dielectric deposition on the electrical performance of a Al2O3 /AlGaN/GaN metal-insulator-semiconductor high electron mobility transistor(MISHEMT),with Al2O3 deposited by atomic layer deposition.The results indicated that the gate leakage was decreased two orders of magnitude after the Al2O3 /AlGaN interface was pretreated by N 2 plasma.Furthermore,effects of N 2 plasma pretreatment on the electrical properties of the AlGaN/Al2O3 interface were investigated by x-ray photoelectron spectroscopy measurements and the interface quality between Al2O3 and AlGaN film was improved.     

Synthesis and ion conductivity of (Bi2O3)0.75(Dy2O3)0.25 ceramics with grain sizes from the nano to the micro scale

Using (Bi₂O₃)_0.75(Dy₂O₃)_0.25 nano-powder synthesized by reverse titration co-precipitation method as raw material, dense ceramics were sintered by both Spark Plasma Sintering (SPS) and pressureless sintering. According to the predominance area diagram of Bi-O binary system, the sintering conditions under SPS were optimized. (Bi₂O₃)_0.75(Dy₂O₃)_0.25 ceramics with relative density higher than 95% and an average grain size of 20 nm were sintered in only 10 min up to 500 °C. During the pressureless sintering process, the grain growth behavior of (Bi₂O₃)_0.75(Dy₂O₃)_0.25 followed a parabolic trend, expressed as D² − D₀² = Kt, and the apparent activation energy of grain growth was found to be 284 kJ mol^− 1. Dense (Bi₂O₃)_0.75(Dy₂O₃)_0.25 ceramics with different grain sizes were obtained, and the effect of grain size on ion conductivity was investigated by impedance spectroscopy. It was shown that the total ion conductivity was not affected by the grain size down to 100 nm, however lower conductivity was measured for the sample with the smallest grain size (20 nm). But, although only the δ phase was evidenced by X-ray diffraction for this sample, a closer inspection by Raman spectroscopy revealed traces of α-Bi₂O₃.