离子束溅射制备Nb_2O_5、Ta_2O_5和SiO_2薄膜的光学、力学特性和微结构

研究了离子束溅射(IBS)制备的Nb_2O_5、Ta_2O_5和SiO_2薄膜的光学特性、力学特性以及薄膜微结构,分析了辅助离子源电压对薄膜特性的影响,并将电子束蒸发、离子辅助沉积和IBS制备的薄膜进行了对比。研究结果表明,IBS制备的薄膜具有更好的光学特性和微结构,同时具有较大的压应力、硬度和杨氏模量;辅助离子源可以改善薄膜的光学特性,调节薄膜应力和减小薄膜表面粗糙度,但对硬度和杨氏模量的影响相对较小。在不同的辅助离子源电压下,IBS制备的Nb_2O_5应力为-152~-281 MPa,Ta_2O_5的应力为-299~-373 MPa,SiO_2的应力为-427~-577 MPa;在合适的工艺参数下,消光系数可小于10~(-4);薄膜表面平整,均方根粗糙度小于0.2nm。     

热蒸发与离子束溅射制备LaF3薄膜的光学特性

研究了钼舟热蒸发工艺和离子束溅射方法制备的单层LaF₃薄膜的特性。首先,采用分光光度计测量了LaF₃薄膜的透射率和反射率光谱,使用不同模型拟合得出薄膜的折射率和消光系数。然后,采用应力仪测量了加热和降温过程中LaF₃薄膜的应力-温度曲线。最后,采用X射线衍射仪测试了薄膜的晶体结构。实验结果表明,热蒸发制备的LaF₃（RH LaF₃）存在折射率的不均匀性,在193 nm,其折射率和消光系数分别为1.687和5×10^-4,而离子束溅射制备的LaF₃（IBS LaF₃）折射率和消光系数分别为1.714和9×10^-4。两种薄膜表现出相反的应力状态,RH LaF₃薄膜具有张应力,而IBS LaF₃具有压应力,退火之后其压应力减小。热蒸发制备的MgF₂/LaF₃减反膜在193 nm透过率为99.4%,反射率为0.04%,离子束溅射制备的AlF₃/LaF₃减反膜透过率为99.2%,反射率为0.1%。     

溅射制备Ta2O5薄膜的表面形貌与光学特性

在室温条件下利用溅射Ta₂O₅靶材的方法制备了Ta₂O₅薄膜,并采用将薄膜两侧的反射率光谱进行比较的简便方法分析评估薄膜的光吸收,发现溅射制备薄膜的额外光吸收源是溅射引起的缺氧形成的,选择适当的溅射功率和含氧比例的工作气体能有效地消除这些缺陷、不用任何加温处理就可制备得到表面平坦和高致密度的高品质Ta₂O₅薄膜. 关键词： 2O₅薄膜')" href="#">Ta₂O₅薄膜 光吸收 表面形貌 磁控溅射     

SiO2薄膜内部短程有序微结构研究

SiO₂薄膜是重要的低折射率材料之一, 针对离子束溅射(IBS)和电子束蒸发(EB)的SiO₂薄膜, 采用红外光谱反演技术获得在400–1500 cm^-1波数内的介电常数, 通过对介电能损函数的分析获得了两种薄膜在横向和纵向光学 振动模式下的振动频率和Si–O–Si键角.研究结果表明, 在EB SiO₂薄膜短程有序范围内, SiO₄的连接方式主要是类柯石英结构、3-平面折叠环和热液石英结构的SiO₄连接方式; 在IBS SiO₂薄膜短程有序范围内, SiO₄的连接方式复杂主要是类柯石英结构、3-平面折叠环、 4-平面折叠环结构和类热液石英结构. 关键词： 2薄膜')" href="#">SiO₂薄膜 离子束溅射 电子束蒸发 短程有序     

超高温度系数V0.97W0.03 O2多晶薄膜的制备研究

将V₂O₅粉体与WO₃粉体均匀混合并压制成靶，用离子束增强沉积加后退火技术在SiO₂衬底上制备掺钨VO₂多晶薄膜.X射线衍射表明，薄膜取向单一，为VO₂结构的［002］相,晶格参数d比VO₂粉晶增大约0.34%；薄膜从半导体相向金属相转变的相变温度约28；室温(300 K)时的电阻-温度系数(TCR)可大于10%/K，是目前红外热成像薄膜TCR的四倍.W离子的半径大于V离子的半径，W的掺入在薄膜中引入了张应力,使薄膜相变温度降低到室温附近，是IBED V_0.97W_0.03O₂薄膜的室温电阻温度系数提高的原因. 关键词： 二氧化钒薄膜 薄膜掺杂 离子束增强沉积     

基于透射光谱确定溅射Al2O3薄膜的光学（已撤稿）

基于反应磁控溅射Al₂O₃薄膜的紫外—可见—近红外透射实验光谱,采用Swanepoel方法结合Wemple-DiDomenico色散模型,方便地导出了Al₂O₃薄膜在200—1100 nm波长范围内的光学常数,包括折射率、色散常数、膜层厚度、吸收系数及能量带隙.研究发现反应磁控溅射Al₂O₃薄膜具有高折射率(1.556— 1.76,测试波长为550 nm)、低吸收和直接能量带隙(3.91—4.20 eV)等光学特性,而且其光学常数对薄膜制备过程中的重要工艺参数——膜层后处理温度表现出强烈的依赖性.此外,在膜层的弱吸收和中等吸收光谱区域内,计算得到的折射率色散曲线与分光光度法的测试结果基本符合,说明本实验中所建立的计算方法在确定反应磁控溅射Al₂O₃薄膜光学常数方面的可靠性. 关键词： 光学常数 Swanepoel方法 2O₃薄膜')" href="#">Al₂O₃薄膜 热处理     

磁控溅射制备Y2O3-TiO2薄膜形貌的研究

室温下采用射频磁控溅射法,在硅衬底上制备了Y₂O₃-TiO₂氧化物复合薄膜.利用XRD(X-ray diffraction)和AFM( atomic force microscopy)分析观察了退火前后样品的物相、形貌等变化,讨论了致密薄膜的生长机理.实验发现,溅射功率越大,薄膜的平整度和致密度越好.对热处理前后样品的结晶结构和表面形貌的分析结果显示,在本实验参数范围内,随着溅射功率的增大,更多的Y₂O_{3关键词： 2}O₃-TiO₂薄膜')" href="#">Y₂O₃-TiO₂薄膜 表面形貌 原子力显微镜 磁控溅射     

溶胶-凝胶法制备Sr2Bi4Ti5O18薄膜及其铁电性能研究

采用溶胶-凝胶法,在氧气氛中和层层晶化的工艺条件下,成功地制备了沉积在Pt/Ti/SiO₂/Si(100)衬底上的铁电性能优良的Sr₂Bi₄Ti₅O₁₈ (SBTi)薄膜,并研究了SBTi薄膜的微结构、表面形貌、铁电性能和疲劳特性.研究表明：薄膜具有单一的层状钙钛矿结构，且为随机取向；薄膜表面光滑，无裂纹，厚度约为725nm；铁电性能测试显示较饱和、方形的电滞回线，当外电场强度为275kV/cm时 关键词： 溶胶-凝胶法 铁电薄膜 2Bi₄Ti₅O₁₈')" href="#">Sr₂Bi₄Ti₅O₁₈     

Bi2Ti2O7/Si薄膜的制备及C-V特性研究

采用化学溶液分解法(CSD)在Si衬底上制备了Bi₂Ti₂O₇薄膜.X射线双晶衍射和原子力显微镜检测表明,所制备的薄膜主要为Bi₂Ti₂O₇相的多晶材料.同时还研究了AuBi₂Ti₂O₇/n-Si(100)结构的电容电压(C-V)特性,结果表明,在Bi₂Ti₂O关键词： C-V特性 2Ti₂O₇薄膜')" href="#">Bi₂Ti₂O₇薄膜 电荷迁移     

椭偏光谱法研究溶胶-凝胶TiO2薄膜的光学常数

以钛酸丁酯为前驱体,采用溶胶-凝胶工艺成功制备了TiO₂薄膜.利用反射式椭圆偏振光谱仪测量了薄膜的椭偏参量Ψ和Δ,并用Cauchy模型对椭偏参数进行数据拟合,得到了薄膜的厚度和光学常数在380—800 nm的色散关系.用分光光度计测量了薄膜的反射率,并用干涉法计算薄膜的厚度;使用原子力显微镜观测了薄膜的表面微结构,分析讨论了不同退火温度处理的薄膜微结构与光学常数之间的关系.研究结果表明,Cauchy模型能较好地符合溶胶-凝胶TiO₂薄 关键词： 光学常数 2薄膜')" href="#">TiO₂薄膜 溶胶-凝胶 椭圆偏振     

Optical and electrical properties of Y2O3 thin films prepared by ion beam assisted deposition

Y₂O₃ thin films were deposited by ion beam assisted deposition (IBAD) and the effects of fabrication parameters such as substrate temperature and ion energy on the structure, optical and electrical properties of the films were investigated. The results show that the deposited Y₂O₃ films had less optical absorption, larger refractive index, and better film crystallinity with the increase of substrate temperature or ion energy. The as-deposited Y₂O₃ films without ion-beam bombardment had larger relative dielectric constant (?_r) and the ?_r decreased with time even over by 40%, while the ?_r of films prepared with high ion energy had less changes, only less than 3%. Also, with the increase of ion energy, the electrical breakdown strength and the figure of merit increased.     

Influence of substrate temperature on structures and dielectric properties of pyrochlore Bi1.5Zn1.0Nb1.5O7 thin films prepared by pulsed laser deposition

The influence of substrate temperature on structural and dielectric properties of cubic pyrochlore Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films prepared by pulsed laser deposition process has been investigated. BZN thin films were deposited on Pt/Ti/SiO₂/Si(1 0 0) substrate and in situ annealed at 700 °C. The results indicate that the substrate temperature has a significant effect on the structural and dielectric properties of BZN thin films. The films exhibit a cubic pyrochlore structure in the substrate temperature range from 550 °C to 700 °C and at the annealing temperature of 700 °C. With further increase of substrate temperature to 750 °C, the phases of Bi₂O₃, BiNbO₄ and Bi₅Nb₃O₁₅ can be detected in the XRD pattern due to the Zn loss. The dielectric constant and loss tangent of the films deposited at 650 °C are 192 and 6 × 10⁻⁴ at 10 kHz, respectively. The tunability is 10% at a dc bias field of 0.9 MV/cm.     

Effect of 100 MeV O7+ ion beam irradiation on structural,optical and electronic properties of SnO2 thin films

In this paper, we present the impact of swift heavy ion beam irradiation on the structural, optical and electronic properties of SnO₂ thin films. Thin films were deposited using the pulsed laser deposition technique on Al₂O₃ substrates. Atomic force microscopy, X-ray diffraction, UV–visible absorption and temperature-dependent resistivity measurements were performed to explore the morphological, structural, optical and electronic properties of the as-deposited and irradiated samples. The peak intensity of the (200) peak was found to decrease monotonously with increasing irradiation fluence. The band gap energy of the 1×10¹¹ ion/cm² irradiated sample was found to increase. The electrical resistivity of the samples showed a continuous increase with the irradiation fluence.     

Effect of sputtering anisotropic ejection on the optical properties and residual stress of Nb2O5 thin films

The effect of sputtering anisotropic ejection on the optical properties and internal stress of niobium pentoxide (Nb₂O₅) films prepared by ion-beam sputtering deposition (IBSD) was investigated experimentally. Thin films were deposited on unheated BK7 glass substrates and silicon wafers at different ejection angles surrounding a metal target. The ejection angles varied from 0° to 75° in increments of 15° for each substrate. It was found that the optical constants of the Nb₂O₅ films were significantly influenced by the sputtering ejection angle. The surface roughness and residual stress in the Nb₂O₅ thin films were also found to vary with the ejection angle. In this work, Nb₂O₅ films had a higher refractive index, lower absorption, lower stress and lower roughness when films deposited at an ejection angle of 30°.     

Si基铁电Bi3.15Nd0.85Ti3O12多层薄膜的一致取向生长和性能的研究

采用脉冲激光沉积(PLD)技术，利用LSCO/CeO₂/YSZ多异质缓冲层，在Si(100)基 片上成功地制备了c轴一致取向的Bi_3.15Nd_0.85Ti₃O12(BNT)铁电薄膜.利用X射线衍射(XRD)和扫描电镜(SEM)分析测定了薄膜的相结构 、取向和形貌特征，考察了沉积温度和氧分压对BNT薄膜微结构、取向和形貌的影响，确定 了BNT薄膜的最佳沉积条件.对在优化的条件下制备得到的BNT薄膜的C-V曲线测试得到了典型 的蝴蝶形曲线，表明该薄膜具有较好的电极化反转存储特性.最后讨论了BNT薄膜铁电性能与 薄膜取向的相关性. 关键词： 3.15Nd_0.85Ti₃O₁₂')" href="#">Bi_3.15Nd_0.85Ti₃O₁₂ 铁电薄 膜 多层异质结 脉冲激光沉积     

Role of plasma activation in tailoring the nanostructure of multifunctional oxides thin films

Potential of O₂ remote plasmas for improving structural, morphological and optical properties of various multifunctional oxides thin films both during plasma assisted growth as well as by post-growth treatments is discussed. In particular, an O₂ remote plasma metalorganic chemical vapor deposition (RP-MOCVD) route is presented for tailoring the structural, morphological and optical properties of Er₂O₃ and ZnO films. Furthermore, post-growth room-temperature remote O₂ plasma treatments of indium-tin-oxides (ITO) films are demonstrated to be effective in improving morphology of ITO films.     

Structural characteristics and morphology of SmxCe1−xO2−x/2 thin films

Effect of the deposition temperature (200 and 500 °C) and composition of Sm_xCe_1−xO_2−x/2 (x = 0, 10.9–15.9 mol%) thin films prepared by electron beam physical vapor deposition (EB-PVD) and Ar⁺ ion beam assisted deposition (IBAD) combined with EB-PVD on structural characteristics and morphology/microstructure was investigated. The X-ray photoelectron spectroscopy (XPS) of the surface and electron probe microanalysis (EPMA) of the bulk of the film revealed the dominant occurrence of Ce⁴⁺ oxidation state, suggesting the presence of CeO₂ phase, which was confirmed by X-ray diffraction (XRD). The Ce³⁺ oxidation states corresponding to Ce₂O₃ phase were in minority. The XRD and scanning electron microscopy (SEM) showed the polycrystalline columnar structure and a rooftop morphology of the surface. Effects of the preparation conditions (temperature, composition, IBAD) on the lattice parameter, grain size, perfection of the columnar growth and its impact on the surface morphology are analyzed and discussed.     

Surface characterization and luminescent properties of SrAl2O4:Eu,Dy nano thin films

SrAl₂O₄:Eu²⁺, Dy³⁺ thin films were grown on Si (1 0 0) substrates in different atmospheres using the pulsed laser deposition (PLD) technique. The effects of vacuum, oxygen (O₂) and argon (Ar) deposition atmospheres on the structural, morphological and photoluminescence (PL) properties of the films were investigated. The films were ablated using a 248 nm KrF excimer laser. Improved PL intensities were obtained from the unannealed films prepared in Ar and O₂ atmospheres compared to those prepared in vacuum. A stable green emission peak at 520 nm, attributed to 4f⁶5d¹→4f⁷ Eu²⁺ transitions was obtained. After annealing the films prepared in vacuum at 800 °C for 2 h, the intensity of the green emission (520 nm) of the thin film increased considerably. The amorphous thin film was crystalline after the annealing process. The diffusion of adventitious C into the nanostructured layers deposited in the Ar and O₂ atmospheres was most probably responsible for the quenching of the PL intensity after annealing.     

The influence of the number of pulses on the morphological and photoluminescence properties of SrAl2O4:Eu,Dy thin films prepared by pulsed laser deposition

The current work reports on the influence of the number of laser pulses on the morphological and photoluminescence properties of SrAl₂O₄:Eu²⁺,Dy³⁺ thin films prepared by the pulsed laser deposition (PLD) technique. Atomic force microscopy (AFM) was used to study the surface topography and morphology of the films. The AFM data showed that the film deposited using a higher number of laser pulses was packed with a uniform layer of coarse grains. In addition, the surface of this film was shown to be relatively rougher than the films deposited at a lower number of pulses. Photoluminescence (PL) data were collected using the Cary Eclipse fluorescence spectrophotometer equipped with a monochromatic xenon lamp. An intense green photoluminescence was observed at 517 nm from the films prepared using a higher number of laser pulses. Consistent with the PL data, the decay time of the film deposited using a higher number of pulses was characteristically longer than those of the other films. The effects of laser pulses on morphology, topography and photoluminescence intensity of the SrAl₂O₄:Eu²⁺,Dy³⁺ thin films are discussed.     

Bi-Sb-Te基热电薄膜温差电池离子束溅射制备与表征

本文采用离子束溅射Bi/Te和Sb/Te二元复合靶,直接制备n型Bi₂Te₃热电薄膜和p型Sb₂Te₃热电薄膜.在退火时间同为1 h的条件下,对所制备的Bi₂Te₃薄膜和Sb₂Te₃薄膜进行不同温度的退火处理,并对其热电性能进行表征.结果表明,在退火温度为150 ℃时,制备的n型Bi₂Te₃关键词： 薄膜温差电池 2Te₃薄膜')" href="#">Sb₂Te₃薄膜 2Te₃薄膜')" href="#">Bi₂Te₃薄膜 离子束溅射