Electron field emission characteristics of nano-catkin carbon films deposited by electron cyclotron resonance microwave plasma chemical vapour deposition

This paper reported that the nano-catkin carbon films were prepared on Si substrates by means of electron cyclotron resonance microwave plasma chemical vapour deposition in a hydrogen and methane mixture. The surface morphology and the structure of the fabricated films were characterized by using scanning electron microscopes and Raman spectroscopy, respectively. The stable field emission properties with a low threshold field of 5V/μm corresponding to a current density of about 1μA/cm^2 and a current density of 3.2mA/cm^2 at an electric field of 10V/μm were obtained from the carbon film deposited at CH4 concentration of 8%. The mechanism that the threshold field decreased with the increase of the CH4 concentration and the high emission current appeared at the high CH4 concentration was explained by using the Fowler-Nordheim theory.     

Oxygen vacancy-induced room-temperature ferromagnetism in D-D neutron irradiated single-crystal TiO2 （001） rutile

Remarkable room temperature ferromagnetism in pure single-crystal rutile TiO2 （001） samples irradiated by D-D neutron has been investigated. By combining X-ray diffraction and positron annihilation lifetime, the contracted lattice has been clearly identified in irradiated TiO2, where Ti4＋ ions can be easily reduced to the state of Ti3＋. As there were no magnetic impurities that could contaminate the samples during the whole procedure, some Ti3＋ ions reside on interstitial or substituted sites accompanied by oxygen vacancies should be responsible for the ferromagnetism.     

TiO_2/Ag composite nanowires for a recyclable surface enhanced Raman scattering substrate

Multifunctional TiO2/Ag composite nanowires are fabricated with a hydrothermal method by precipitating Ag nanoparticles （NPs） on the surfaces of TiO2 nanowires. This hierarchical one-dimensional （1D） nanostructure can be used as a surface enhanced Raman scattering （SERS） substrate with high sensitivity, for detecting the rhodamine 6G （R6G） in a wide range of low concentrations （from 1 × 10 6 M to 1 × 10-12 M）. In addition, the substrate can be self-cleaned under the irradiation of ultraviolet （UV） light due to the superior photocatalytic capacity of the TiO2/Ag composite nanostructure, making the recycled use of SERS substrates closer to reality. With both the evident SERS performance and high efficiency of photocatalytic capacity, such TiOz/Ag composite nanowires demonstrate considerable potential in the chemical sensing of organic pollutants.     

Structure, room-temperature magnetic and optical properties of Mn-doped TiO2 nano powders prepared by the sol-gel process

TiO 2 nano powders with Mn concentration of 0 at%-12 at% were synthesized by the sol-gel process,and were annealed at 500 C and 800 C in air for 2 hrs.X-ray diffraction (XRD) measurements indicate that the Mn-TiO 2 nano powders with Mn concentration of 1 at% and 2 at% annealed at 500 and 800 C are of pure anatase and rutile,respectively.The scanning electron microscope (SEM) observations reveal that the crystal grain size increases with the annealing temperature,and the high resolution transmission electron microscopy (HRTEM) investigations further indicate that the samples are well crystallized,confirming that Mn has doped into the TiO 2 crystal lattice effectively.The room temperature ferromagnetism,which could be explained within the scope of the bound magnetic polaron (BMP) theory,is detected in the Mn-TiO 2 samples with Mn concentration of 2 at%,and the magnetization of the powders annealed at 500 C is stronger than that of the sample treated at 800 C.The UV-VIS diffuse reflectance spectra results demonstrate that the absorption of the TiO 2 powders could be enlarged by the enhanced trapped electron absorption caused by Mn doping.     

Analysis of optoelectronic properties of TiO_2 nanowiers/Si heterojunction arrays

The optoelectronic properties of n-TiO2NW/p-Si heterojunction fabricated by depositing TiO2 nanowires on a p-Si substrate are studied. Under excitation at a wavelength of 370 nm, the TiO2 nanowires produce a light emission at 435 nm due to the emission of free excitons. The I-V characteristics are measured to investigate the heterojunction effects under the dark environment and ultraviolet （UV） illumination, n-TiOzNW/p-Si has a p-n junction formed in the n-TiOz/p-Si beterojunction. TiO2NW/Si photodiode produces a pbotocurrent larger than dark current under UV illumination. It is observed that UV photons are absorbed in TiO2 and the heterojunction shows a 0.034-A/W responsivity at 4-V reverse bias.     

Templated synthesis of highly ordered mesoporous cobalt ferrite and its microwave absorption properties

Based on the nanocasting strategy, highly ordered mesoporous CoFe2O4 is synthesized via the ‘two-solvent’ impregnation method using a mesoporous SBA-15 template. An ordered two-dimensional(P6mm) structure is preserved for the CoFe2O4/SBA-15 composite after the nanocasting. After the SBA-15 template is dissolved by NaOH solution, a mesoporous structure composed of aligned nanoparticles can be obtained, and the P6 mm structure of the parent SBA-15is preserved. With a high specific surface area(above 90 m2/g) and ferromagnetic behavior, the obtained material shows potential in light weight microwave absorption application. The minimum reflection loss(RL) can reach-18 dB at about16 GHz with a thickness of 2 mm and the corresponding absorption bandwidth is 4.5 GHz.     

On-chip optical pulse shaper for arbitrary waveform generation

We propose and demonstrate a silicon-on-insulator(SOI) on-chip optical pulse shaper based on four-tap finite impulse response. Due to different width designs in phase region of each tap, the phase differences for all taps are controlled by an external thermal source, resulting in an optical pulse shaper. We further demonstrate optical arbitrary waveform generation based on the optical pulse shaper assisted by an optical frequency comb injection. Four different optical waveforms are generated when setting the central wavelengths at 1533.78 nm and 1547.1 nm and setting the thermal source temperatures at 23℃ and 33℃, respectively. Our scheme has distinct advantages of compactness, capability for integrating with electronics since the integrated silicon waveguide is employed.     

Bidirectional reflectance one-dimensional rough distribution function modeling of surface in the microwave band

In this study, the bidirectional reflectance distribution function （BRDF） of a one-dimensional conducting rough surface and a dielectric rough surface are calculated with different frequencies and roughness values in the microwave band by using the method of moments, and the relationship between the bistatic scattering coefficient and the BRDF of a rough surface is expressed. From the theory of the parameters of the rough surface BRDF, the parameters of the BRDF are obtained using a genetic algorithm. The BRDF of a rough surface is calculated using the obtained parameter values. Further, the fitting values and theoretical calculations of the BRDF are compared, and the optimization results are in agreement with the theoretical calculation results. Finally, a reference for BRDF modeling of a Gaussian rough surface in the microwave band is provided by the proposed method.     

Preparation of multi-walled carbon nanotube–Fe composites and their application as light weight and broadband electromagnetic wave absorbers

Multi-walled carbon nanotube （MWCNT）-Fe composites were prepared via the metal organic chemical vapor deposi- tion by depositing iron pentacarbonyl on the surface of MWCNTs. The structural and morphological analyses demonstrated that Fe nanoparticles were deposited on the surface of the MWCNTs. The electromagnetic properties of the MWCNTs were significantly changed, and the absorbing capacity evidently improved after the Fe deposition on the MWCNT surface. A minimum reflection loss of -29.4 dB was observed at 8.39 GHz, and the less than -10 dB bandwidth was about 10.6 GHz, which covered the whole X band （8.2-12.4 GHz） and the whole Ku band （12.4-18 GHz）, indicating that the MWCNT-Fe composites could be used as an effective microwave absorption material.     

Microwave ferromagnetic properties of as-deposited Co_2FeSi Heusler alloy films prepared by oblique sputtering

The Co2 FeSi films are deposited on Si(100) substrates by an oblique sputtering method at ambient temperature. It is revealed that the microwave ferromagnetic properties of Co2 FeSi films are sensitive to sample position and sputtering power. It is exciting that the as-deposited films without any magnetic annealing exhibit high in-plane uniaxial anisotropy fields in a range of 200 Oe–330 Oe(1 Oe = 79.5775 A·m-1), and low coercivities in a range of 5 Oe–28 Oe. As a result,high self-biased ferromagnetic resonance frequency up to 4.75 GHz is achieved in as-deposited oblique sputtered films.These results indicate that Co2 FeSi Heusler alloy films are promising in practical applications of RF/microwave devices.     

HEM11 mode magnetically insulated transmission line oscillator： Simulation and experiment

A novel magnetically insulated transmission line oscillator （MILO） in which a modified HEM11 mode is taken as its main interaction mode （HEM11 mode MILO） is simulated and experimented in this paper. The excitation of the oscillation mode is made possible by carefully adjusting the arrangement of each resonant cavity in a two-dimensional slow wave structure. The special feature of such a device is that in the slow-wave-structure region, the interaction mode is HEM11 mode which is a TM-like one that could interact with electron beams effectively; and in the coaxial output region, the microwave mode is TE11 mode which has a favourable field density pattern to be directly radiated. Employing an electron beam of about 441 kV and 39.7 kA, the HEM11 mode MILO generates a high power microwave output of about 1.47 GW at 1.45 GHz in particle-in-cell simulation. The power conversion efficiency is about 8.4 % and the generated microwave is in a TEll-like circular polarization mode. In a preliminary experiment investigation, high power microwave is detected from the device with a frequency of 1.46 GHz, an output energy of 43 J 47 J, and a pulse duration of 44 ns-49 ns when the input voltage is 430 kV450 kV, and the diode current is 37 kA-39 kA.     

Mode control in a high gain relativistic klystron amplifier with 3 GW output power

Higher mode excitation is very serious in the relativistic klystron amplifier, especially for the high gain relativistic amplifier working at tens of kilo-amperes. The mechanism of higher mode excitation is explored in the FIC simulation and it is shown that insufficient separation of adjacent cavities is the main cause of higher mode excitation. So RF lossy material mounted on the drift tube wall is adopted to suppress higher mode excitation. A high gain S-band relativistic klystron amplifier is designed for the beam current of 13 kA and the voltage of 1 MV. PIC simulation shows that the output power is 3.2 GW when the input power is only 2.8 kW.     

High microwave absorption performances for single-walled carbon nanotube–epoxy composites with ultra-low loadings

Microwave-absorbing polymeric composites based on single-walled carbon nanotubes(SWNTs) are fabricated via a simple yet versatile method, and these SWNT–epoxy composites exhibit very impressive microwave absorption performances in a range of 2 GHz–18 GHz. For instance, a maximum absorbing value as high as 28 dB can be achieved for each of these SWNT–epoxy composites(1.3-mm thickness) with only 1 wt% loading of SWNTs, and about 4.8 GHz bandwidth,corresponding to a microwave absorption performance higher than 10 dB, is obtained. Furthermore, such low and appropriate loadings of SWNTs also enhance the mechanical strength of the composite. It is suggested that these remarkable results are mainly attributable to the excellent intrinsic properties of SWNTs and their homogeneous dispersion state in the polymer matrix.     

Microwave propagation with the gas breakdown

By combining the microwave propagation theory and the gas breakdown theory, the microwave propagation with the gas breakdown is analyzed theoretically. Particle-in-cell/Monte Carlo collision （PIC/MCC） simulations are carried out to verify the theoretical results. Based on this theoretical method, the breakdown phenomenon of the pulse microwave is analyzed. The results show that the product values of the initial electron density and the propagation length are the criterion to distinguish the pulse peak decline breakdown and the pulse width reduction breakdown. Furthermore, the energy transmission is also studied, which shows that the total output energy is approximately independent of the input electric field if the electric field is not extremely large.     

First-principles study on anatase TiO2 codoped with nitrogen and praseodymium

The crystal structures, electronic structures and optical properties of nitrogen or/and praseodymium doped anatase TiO₂ were calculated by first principles with the plane-wave ultrasoft pseudopotential method based on density functional theory. Highly efficient visible-light-induced nitrogen or/and praseodymium doped anatase TiO₂ nanocrystal photocatalyst were synthesized by a microwave chemical method. The calculated results show that the photocatalytic activity of TiO₂ can be enhanced by N doping or Pr doping, and can be further enhanced by N+Pr codoping. The band gap change of the codoping TiO₂ is more obvious than that of the single ion doping, which results in the red shift of the optical absorption edges. The results are of great significance for the understanding and further development of visible-light response high activity modified TiO₂ photocatalyst. The photocatalytic activity of the samples for methyl blue degradation was investigated under the irradiation of fluorescent light. The experimental results show that the codoping TiO₂ photocatalytic activity is obviously higher than that of the single ion doping. The experimental results accord with the calculated results.     

Ferromagnetic resonance frequency shift model of laminated magnetoelectric structure tuned by electric field

Based on Smith-Beljers theory and classical laminate theory, an explicit model is proposed for the ferromagnetic resonance （FMR） frequency shift of a stress-mediumed laminated magnetoelectric structure tuned by an electric field. This model can effectively predict the experimental phenomenon that the FMR frequency increases under a parallel magnetic field and decreases under a perpendicular magnetic field when the electric field ranges from - 10 kV/m to 10 kV/m. Besides, this theory further shows that the FMR frequency increases monotonically as the angle between the direction of the external magnetic field and the outside normal direction of the laminated structure increases, and the frequency will increase as great as 7 GHz. In addition, when the angle reaches a certain critical value, the external electric field fails to tune the FMR frequency. When the angle is above the critical value, the increase of the electric field induces the FMR frequency to increase, and the opposite scenario happens when it is below the critical value. When the angle is 90~ （parallel magnetic field）, the FMR frequency is the most sensitive to the change of the electric field.     

Effects of V/III ratio on a-plane GaN epilayers with an InGaN interlayer

The effects of V/Ill growth flux ratio on a-plane GaN films grown on r-plane sapphire substrates with an InGaN interlayer are investigated. The surface morphology, crystalline quality, strain states, and density of basal stacking faults were found to depend heavily upon the V/III ratio. With decreasing V/III ratio, the surface morphology and crystal quality first improved and then deteriorated, and the density of the basal-plane stacking faults also first decreased and then increased. The optimal V/III ratio growth condition for the best surface morphology and crystalline quality and the smallest basal-plane stacking fault density of a-GaN films are found. We also found that the formation of basal-plane stacking faults is an effective way to release strain.     

Shear Viscosity of Hot QED at Finite Chemical Potential from Kubo Formula

Within the framework of finite temperature field theory this paper discusses the shear viscosity of hot QED plasma through Kubo formula at one-loop skeleton diagram level with a finite chemical potential. The effective widths （damping rates） are introduced to regulate the pinch singularities and then gives a reliable estimation of the shear viscous coefficient. The finite chemical potential contributes positively compared to the pure temperature case. The result agrees with that from the kinetics theory qualitatively.     

Hawking Radiation of Charged Particles in Reissner-NordstrSm Black Hole

We extend the method that Banerjee and Majhi have used to discuss Hawking radiation. Under the condition that the total energy and electrical charge of spacetime are conserved, we investigate Hawking radiation of the charged black hole by a new Tortoise coordinate transformation. Taking the reaction of the radiation of the particle to the spacetime into consideration, we not only derive the radiation spectrum that satisfies the unitary principle in quantum mechanics but also show that the contribution of ingoing particles is equal to the one of outgoing particles on the similar chemical potential term in radiation spectrum caused by charged particles.     

Structural and photoluminescence properties of terbium-doped zinc oxide nanoparticles

We present in this paper a study of the structural and photoluminescence （PL） properties of terbium （Tb） doped zinc oxide （ZnO） nanoparticles synthesized by a simple low temperature chemical precipitation method, using zinc acetate and terbium nitrate in an isopropanol medium with diethanolamine （DEA） as the capping agent at 60 ℃. The as-prepared samples were heat treated and the PL of the annealed samples were studied. The prepared nanoparticles were characterized with X-ray diffraction （XRD）. The XRD patterns show the pattern of typical ZnO nanoparticles and correspond with the standard XRD pattern given by JCPDS card No. 36-1451, showing the hexagonal phase structure. The PL intensity was enhanced due to Tb^3＋ doping, and it decreased at higher concentrations of Tb^3＋ doping after reaching a certain optimum concentration. The PL spectra of Tb^3＋ doped samples exhibited blue, bluish green, and green emissions at 460 nm （5^D3 - 7^F3）, 484 nm （5^D4 - 7^F6）, and 530 nm （5^D4 - 7^F5）, respectively, which were more intense than the emissions for the undoped ZnO sample. Based on the results, an energy level schematic diagram was proposed to explain the possible electron transition processes.