不同衬底上Pb(Zr0.52Ti0.48)O3择优取向铁电薄膜的制备和研究

通过MOD法在Si(100)和Pt(111)/Ti/SiO2/Si基片上制备出LaNiO3 (LNO)薄膜.再通过修正的Sol-gel法,在Pt(111)/Ti/SiO2/Si,LNO/Si(100)和LNO/Pt/Ti/SiO2/Si三种衬底上制备出具有择优取向的Pb(Zr0.52Ti0.48)O3铁电薄膜.经XRD分析表明,LNO薄膜具有(100)择优取向的类钙钛矿结构;PZT薄膜均具有钙钛矿结构,且在Pt(111)/Ti/SiO2/Si衬底上的薄膜以(110)择优取向,在LNO/Pt/Ti/SiO2/Si和LNO/Si(100)衬底上的薄膜以(100)择优取向.经场发射SEM分析和介电、铁电性能测试表明,在LNO/Si和LNO/Pt/Ti/SiO2/Si衬底上的PZT薄膜的平均粒径、介电常数以及剩余极化强度均比以Pt/Ti/SiO2/Si为衬底的薄膜大.     

La0.3Sr0.7TiO3模板层对Pb(Zr0.5Ti0.5)O3薄膜的铁电性能增强效应的研究

通过sol-gel法在Si (111) 基片上分别制备了LaNiO₃(LNO)底电极和LaNiO₃/La_0.3Sr_0.7TiO₃ (LNO/LSTO)底电极.然后采用sol-gel 方法，在两种衬底上分别制备了Pb (Zr_0.5Ti_0.5)O₃ (PZT)铁电薄膜.XRD分析表明，两种PZT薄膜均具有钙钛矿结构，且在LNO底电极上的PZT薄膜呈(100) 择优取向，而在LNO/LSTO底电极上的PZT薄膜呈随机取向.铁电性能测试表明，相对LNO衬底上制备的PZT薄膜，在LNO/LSTO底电极上制备的PZT薄膜的剩余极化强度得到了有效的增强，同时矫顽场也增大.介电常数和漏电流的测试表明，LNO/LSTO底电极上制备的PZT薄膜具有大的介电常数和漏电流. 关键词： PZT薄膜 铁电性 漏电流 0.3Sr_0.7TiO₃')" href="#">La_0.3Sr_0.7TiO₃     

(111)择优取向的Pb(Zr0.52Ti0.48)O3铁电薄膜的制备及研究

选用不同浓度的Pb(Zr_0.52Ti_0.48)O₃溶胶，用Sol-gel法在Pt/Ti/SiO₂/Si基片上沉积一层厚度不同的Pb(Zr_0.52Ti_0.48)O₃ (PZT52)过渡层，经400℃烘烤、550℃退火等程序后，再用Sol-gel法在PZT52过渡层上沉积Pb(Zr_0.52Ti_0.48)O _{关键词： PZT铁电薄膜 择优取向 过渡层 剩余极化强度}     

La0.3Sr0.7TiO3模板层对Pb(Zr0.5Ti0.5)O3薄膜的铁电性能增强效应的研究

通过sol-gel法在si(111)基片上分别制备了LaNiO3(LNO)底电极和LaNiO3/Sr0.7TiO3(LNO/LSTO)底电极.然后采用sol-gel方法,在两种衬底上分别制备了Pb(Zr0.5Ti0.5)O3(PZT)铁电薄膜.XRD分析表明,两种PZT薄膜均具有钙钛矿结构,且在LNO底电极上的PZT薄膜呈(100)择优取向,而在LNO/LSTO底电极上的PZT薄膜呈随机取向.铁电性能测试表明,相对LNO衬底上制备的PZT薄膜,在LNO/LSTO底电极上制备的PZT薄膜的剩余极化强度得到了有效的增强,同时矫顽场也增大.介电常数和漏电流的测试表明,LNO/LSTO底电极上制备的PZT薄膜具有大的介电常数和漏电流.     

化学溶液法制备的Pb(Mg1/3Nb2/3)O3-PbTiO3薄膜的光学性能

用化学溶液方法在宝石衬底及有LaNiO₃缓冲层的Pt/TiO₂/SiO₂/Si衬底上制备了92%Pb(Mg_1/3Nb_2/3)O₃-8%PbTiO₃(PMNT)薄膜，X射线衍射测试结果表明：在有LaNiO₃缓冲层的Pt/TiO₂/SiO₂/Si衬底上制备的PMNT薄膜几乎是纯钙钛矿相，且薄膜 关键词： PMNT薄膜 光学性能 化学溶液法     

复合薄膜NiFe2 O4-BiFeO3 中的磁电耦合

采用化学溶液沉积法(CSD)在Au/Ti/SiO₂/Si衬底上通过自组装生长制备了BiFeO₃-NiFe₂O₄ (BFO-NFO)多铁性复合薄膜.X射线衍射图谱(XRD)显示形成了分离的钙钛矿结构的铁电相BFO和尖晶石结构的铁磁相NFO. NFO的引入导致复合薄膜的泄漏电流减小,剩余极化强度增加.相比于纯BFO薄膜,0.25NFO-0.75BFO样品泄漏电流下降了约两个数量级,剩余极化强度( M _{关键词： 多铁性复合薄膜 磁电耦合 铁电性 铁磁性}     

(111)取向(Pb,La)TiO3铁电薄膜中90°纳米带状畴与热释电性能的研究

采用射频磁控溅射技术在Pt/Ti/SiO₂/Si(100)衬底上生长了掺镧钛酸铅(PLT)铁电薄膜.用X射线衍射技术(XRD)研究了PLT薄膜结晶性能，结果表明PLT薄膜为 (111)择优取向钙钛矿相织构.使用原子力显微镜(AFM)和压电响应力显微镜(PFM) 分别观察了PLT薄膜的表面形貌和对应区域的电畴结构.PFM观察显示PLT薄膜中存在90°纳米带状畴，电畴的极化为首尾相接的低能量的排列方式，带状畴的宽度为20—60nm.研究了PLT10铁电薄膜的制备条件与性能之间的关系.发现在优化条件下制备的PLT10铁电薄膜的介电常数ε_r为365、介电损耗tgδ为0.02，热释电系数γ为2.18×10^-8C·(cm²·K)^-1，可以满足制备非制冷红外探测器的需要. 关键词： PLT薄膜 电畴 PFM 极化     

含铜铁电电容器SrRuO3/Pb(Zr0.4Ti0.6)O3/SrRuO3/Ni-Al/Cu/Ni-Al/SiO2/Si异质结的研究

应用磁控溅射法以Ni-Al同时作为Cu与SiO₂/Si,Cu与SRO薄膜之间的阻挡层材料,将Cu与SiO₂/Si衬底和氧化物薄膜电极隔离,避免它们在高温氧气氛中发生化学反应和互扩散,实现了Cu薄膜与氧化物铁电电容器的集成.采用X射线衍射仪(XRD)和原子力显微镜(AFM)研究了不同温度下快速退火的SrRuO₃(SRO)/Ni-Al/Cu/Ni-Al/SiO₂/Si含Cu异质结的微结构和表面形貌,结果发现SRO/Ni-Al/Cu/Ni-Al/SiO₂/Si含Cu多层异质结薄膜在高达750 ℃仍然具有较强的Cu衍射峰和比较平整的表面,显示出了很好的高温热稳定性.研究了"室温长高温退"和"低温长高温退"两种工艺手段,发现在制备含Cu多层氧化物薄膜异质结时,低温长高温后退火的方式要优于常规的室温长高温后退火方式,通过低温长高温退工艺可以缓解应力、削弱界面粗化和避免高温生长对阻挡层和Cu薄膜结构的破坏.最后结合sol-gel法将Pb(Zr_0.4Ti_0.6)O₃(PZT)生长在该含Cu异质结上,制备得SRO/PZT/SRO/Ni-Al/Cu/Ni-Al/SiO₂/Si含Cu铁电电容器,研究了电容器的薄膜结构、铁电性能和漏电特性等,发现制备的含Cu铁电电容器具有很好的铁电性能,如电滞回线趋势饱和,剩余极化强度高达~42 μC/cm²,矫顽电压为~1.0 V,介电常数~1600,漏电流~1.83×10^-4 A/cm²,以及良好的抗疲劳特性和保持特性等,表明导电性优良的Cu薄膜可以应用于高密度高性能铁电电容器.对其漏电机理研究表明,SRO/PZT/SRO含Cu铁电电容器满足空间电荷限制传导机理. 关键词： Cu PZT 铁电电容器 Ni-Al     

溶胶-凝胶法制备Sr2Bi4Ti5O18薄膜及其铁电性能研究

采用溶胶-凝胶法,在氧气氛中和层层晶化的工艺条件下,成功地制备了沉积在Pt/Ti/SiO₂/Si(100)衬底上的铁电性能优良的Sr₂Bi₄Ti₅O₁₈ (SBTi)薄膜,并研究了SBTi薄膜的微结构、表面形貌、铁电性能和疲劳特性.研究表明：薄膜具有单一的层状钙钛矿结构，且为随机取向；薄膜表面光滑，无裂纹，厚度约为725nm；铁电性能测试显示较饱和、方形的电滞回线，当外电场强度为275kV/cm时 关键词： 溶胶-凝胶法 铁电薄膜 2Bi₄Ti₅O₁₈')" href="#">Sr₂Bi₄Ti₅O₁₈     

La掺杂对Bi4Ti3O12薄膜铁电性能的影响

利用Sol-Gel法在Pt/Ti/SiO₂/Si衬底上制备出Bi₄Ti₃O₁₂和Bi_3.25La_0.75Ti₃O₁₂薄膜，研究了La掺杂对Bi₄Ti₃O₁₂薄膜的晶体结构、铁电性能和疲劳特性的影响，发现La掺杂没有改变Bi₄Ti₃O₁₂薄膜的基本晶体结构，并且提高了Bi₄Ti₃O₁₂铁电薄膜的剩余极化值和抗疲劳性能，对La掺杂改善Bi₄Ti₃O₁₂铁电薄膜性能的机理进行了讨论. 关键词： 铁电性能 4Ti₃O₁₂薄膜')" href="#">Bi₄Ti₃O₁₂薄膜 3.25La_0.75Ti₃O₁₂薄膜')" href="#">Bi_3.25La_0.75Ti₃O₁₂薄膜 sol-gel法 La掺杂     

Effects of substrates on the structure and dielectric properties of Ba(Sn0.15Ti0.85)O3 thin films

Ba(Sn_0.15Ti_0.85)O₃ (BTS) thin films were grown on Pt(1 1 1)/Ti/SiO₂/Si and LaNiO₃(LNO)/Pt(1 1 1)/Ti/SiO₂/Si substrates by a sol-gel processing technique, respectively. The BTS thin films deposited on annealed Pt(1 1 1)/Ti/SiO₂/Si and annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrates exhibited strong (1 1 1) and perfect (1 0 0) orientations, respectively. The BTS thin films grown on un-annealed Pt(1 1 1)/Ti/SiO₂/Si substrates showed random orientation with intense (1 1 0) peak, while the films deposited on un-annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrate exhibited random orientation with intense (1 0 0) peak, respectively. The dielectric constant of the BTS films deposited on annealed Pt(1 1 1)/Ti/SiO₂/Si, annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si, un-annealed Pt(1 1 1)/Ti/SiO₂/Si and un-annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrates was 512, 565, 386 and 437, respectively, measured at a frequency of 100 kHz. A high tunability of 49.7% was obtained for the films deposited on annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrate, measured at the frequency of 100 kHz with an applied electric field of 200 kV/cm. The high tunability has been attributed to the (1 0 0) texture of the films and larger grain sizes.     

Influence of MgO and ZrO2 buffer layers on dielectric properties of Ba(Zr0.20Ti0.80)O3 thin films prepared by sol-gel processing

Ba(Zr_0.20Ti_0.80)O₃ (BZT) thin films are deposited on Pt(1 1 1)/Ti/SiO₂/Si, MgO and ZrO₂ buffered Pt(1 1 1)/Ti/SiO₂/Si substrates by a sol-gel process. The BZT thin films directly grown on Pt(1 1 1)/Ti/SiO₂/Si substrates exhibit highly (1 1 1) preferred orientation, while the films deposited on Pt(1 1 1)/Ti/SiO₂/Si substrates with MgO and ZrO₂ buffer layers show highly (1 1 0) preferred orientation. At 100 kHz, dielectric constants are 417, 311 and 321 for the BZT thin films grown on Pt(1 1 1)/Ti/SiO₂/Si, MgO and ZrO₂ buffered Pt(1 1 1)/Ti/SiO₂/Si substrates, respectively. The difference in dielectric properties of three BZT films can be attributed to the series capacitance effect, interface conditions and their orientations.     

Structural and electrical properties of (Na0.85K0.15)0.5Bi0.5TiO3 thin films deposited on LaNiO3 and Pt bottom electrodes

(Na_0.85K_0.15)_0.5Bi_0.5TiO₃ thin films were deposited on LaNiO₃(LNO)/SiO₂/Si(1 0 0) and Pt/Ti/SiO₂/Si(1 0 0) substrates by metal-organic decomposition, and the effects of bottom electrodes LNO and Pt on the ferroelectric, dielectric and piezoelectric properties were investigated by ferroelectric tester, impedance analyzer and scanning probe microscopy, respectively. For the thin films deposited on LNO and Pt electrodes, the remnant polarization 2P_r are about 22.6 and 8.8 μC/cm² under 375 kV/cm, the dielectric constants 238 and 579 at 10 kHz, the dielectric losses 0.06 and 0.30 at 10 kHz, the statistic d_33eff values 95 and 81 pm/V. The improved piezoelectric properties could make (Na_1−xK_x)_0.5Bi_0.5TiO₃ thin film as a promising candidate for piezoelectric thin film devices.     

Dielectric and piezoelectric properties of the Ba0.92Ca0.08Ti0.95Zr0.05O3 thin films grown on different substrate

Lead free Ba_0.92Ca_0.08Ti_0.95Zr_0.05O₃ (BCZT) thin films were deposited on Pt/Ti/SiO₂/Si and LaNiO₃(LNO)/Pt/Ti/SiO₂/Si substrates by a sol–gel processing technique, respectively. The effects of substrate on structure, dielectric and piezoelectric properties were investigated in detail. The BCZT thin films deposited on LNO/Pt/Ti/SiO₂/Si substrates exhibit (100) orientation, larger grain size and higher dielectric tunability (64%). The BCZT thin films deposited on Pt/Ti/SiO₂/Si exhibit (110) orientation, higher Curie temperature (75 °C), better piezoelectric property (d₃₃ of 50 pm/V) and lower dielectric loss (0.02). The differences in dielectric and piezoelectric properties in the two kinds of oriented BCZT films should be attributed to the difference of structure, in-plane stress and polarization rotation in orientation engineered BCZT films.     

不同晶化工艺对非晶PZT纳米薄膜形核取向生长机理的影响

射频磁控溅射法室温下在Pt/Ti/SiO2/Si上制备非晶Pb(Zr048Ti052)O3薄膜，非晶PZT薄膜分别经常规炉退火(CFA)处理和快速热退火(RTA)处理晶化为（100），（111）不同择优取向的多晶薄膜. 采用x射线衍射测定了薄膜相组分、择优取向度；用原子力显微镜和压电响应力显微镜观察了薄膜表面形貌，以及对应区域由自发极化形成的铁电畴像，观察了不同取向薄膜的电畴分布特征. 结果表明，RTA晶化过程钙钛矿结构PZT结晶主要以PZT/Pt界面处的PtPb化合物为成核点异质形核并类似外延的结晶生长，沿界面结晶速率远大于垂直膜面结晶速率，而CFA晶化样品成核发生在膜内杂质缺陷处，以同质成核为主. 不同的成核机理导致了不同晶面择优取向生长. 关键词： PZT薄膜 结晶 形核 力显微技术     

Enhanced ferroelectric property of (Pb0.95Ca0.05)(Nb0.02Zr0.80Ti0.20)O3 thin films prepared by RF magnetron sputtering

(Pb_0.95Ca_0.05)(Nb_0.02Zr_0.80Ti_0.20)O₃ [PCNZT] thin films were deposited on the Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by RF magnetron sputtering with and without a LaNiO₃ [LNO] buffer layer. Ca and Nb elements in PZT films enhance the ferroelectric property, LaNiO₃ buffer layer improves the crystal quality of the PCNZT thin films. PCNZT thin films possess better ferroelectric property than that of PZT films for Ca and Nb ion substitution, moreover, PCNZT thin films with a LNO buffer layer possess (1 0 0) orientation and good ferroelectric properties with high remnant polarization (P_r = 38.1 μC/cm²), and low coercive field (E_c = 65 kV/cm), which is also better than that of PCNZT thin films without a LNO buffer layer (P_r = 27.9 μC/cm², E_c = 74 kV/cm). The result shows that enhanced ferroelectric property of PZT films can be obtained by ion substitution and buffer layer.     

High pyroelectric Ba0.65Sr0.35TiO3 thin films with Ba0.65Sr0.35RuO3 seeding-layer for monolithic ferroelectric bolometer

Ba_0.65Sr_0.35TiO₃ (BST) thin films were deposited by RF sputtering with a very thin Ba_0.65Sr_0.35RuO₃ (BSR) seeding-layer on Pt/Ti/SiO₂/Si substrate. The crystallization of BST thin films and the surface morphology of BSR seeding-layer were characterized by X-ray diffraction (XRD) and atomic force microscopy (AFM), respectively. XRD patterns show that the BSR seeding-layer affected the orientation of BST thin film, which is highly a-axis textured. It was also found that the BSR seeding-layer had a marked influence on the dielectric properties of BST thin films. Comparing with BST thin films directly deposited on Pt electrode, the dielectric relaxation can be suppressed and dielectric constant increased due to a possible reduction of interface oxygen vacancies at BST/BSR interface. Moreover, J–V measurement indicates that the leakage current density of BST thin films on BSR seeding-layer were greatly reduced compared with that of BST thin films directly on Pt electrodes. The pyroelectric coefficient of BST thin films with BSR seeding-layer is 7.57 × 10⁻⁷ C cm⁻² K⁻¹ at 6 V/μm at room temperature (RT). Our results reveal that high pyroelectric property of BST thin film could be achievable using BSR seeding-layer as a special buffer.     

(111)取向生长Pb(Zr0:95Ti0:05)O3纳米晶薄膜的铁电与热释电特性

" 在Pt/Ti/SiO2/Si基片上用溶胶-凝胶法与快速退火工艺制备了300 nm厚的锆钛酸铅Pb(Zr0:95Ti0:05)O3 (PZT95/5)反铁电薄膜．结果显示600~700 ℃晶化处理的钙钛矿PZT95/5薄膜具有高度(111)取向生长特性．薄膜的电性能测量采用金属-铁电-金属电容器结构．在20 V电压作用下,600~700 ℃晶化处理的PZT95/5薄膜显示出饱和电滞回线．在1 kHz下,600、650和700 ℃晶化的薄膜介电常数与损耗分别为519与0.028、677与0.029、987