MSM结构ZnO/Cu薄膜的接触特性

利用脉冲激光沉积(PLD)法在Si(111)衬底上分别生长了ZnO薄膜和Cu薄膜, 用Cu薄膜作电极,研究了ZnO薄膜与Cu薄膜的接触特性。分别用X射线衍射仪、扫描电子显微镜和I-V测试的方法对样品的晶体质量、结构和电学性质进行了测试。结果表明:样品中ZnO薄膜和Cu薄膜均具有高度的择优取向;当Cu和 ZnO直接接触时,样品的I-V特性是非线性的;当Cu和 ZnO之间通过ZnO:Cu层间接接触时形成良好的欧姆接触,而且退火后欧姆接触性能明显提高,电阻率降低约2/3。本研究为价格低廉的Cu电极成为ZnO基器件的欧姆电极提供了一定的依据。     

退火温度对硼掺杂纳米金刚石薄膜微结构和p型导电性能的影响

采用热丝化学气相沉积法制备硼掺杂纳米金刚石 (BDND) 薄膜, 并对薄膜进行真空退火处理, 系统研究退火温度对BDND薄膜微结构和电学性能的影响. Hall效应测试结果表明掺B浓度为5000 ppm (NHB) 的样品的电阻率较掺B浓度为500 ppm (NLB) 的样品的低, 载流子浓度高, Hall迁移率下降. 1000 ℃退火后, NLB和NHB 样品的迁移率分别为53.3和39.3 cm²·V^-1·s^-1, 薄膜的迁移率较未退火样品提高, 电阻率降低. 高分辨透射电镜、紫外和可见光拉曼光谱测试结果表明, NLB样品的金刚石相含量较NHB样品高, 高的硼掺杂浓度使薄膜中的金刚石晶粒产生较大的晶格畸变. 经1000 ℃退火后, NLB和NHB薄膜中纳米金刚石相含量较未退火时增大, 说明薄膜中部分非晶碳转变为金刚石相, 为晶界上B扩散到纳米金刚石晶粒中提供了机会, 使得纳米金刚石晶粒中B浓度提高, 增强纳米金刚石晶粒的导电能力, 提高薄膜电学性能. 1000 ℃退火能够恢复纳米金刚石晶粒的晶格完整性, 减小由掺杂引起的内应力, 从而提高薄膜的电学性能. 可见光Raman光谱测试结果表明, 1000℃退火后, Raman谱图中反式聚乙炔 (TPA) 的1140 cm^-1峰消失, 此时薄膜电学性能较好, 说明TPA减少有利于提高薄膜的电学性能. 退火后金刚石相含量的增大、金刚石晶粒的完整性提高及TPA含量的大量减少有利于提高薄膜的电学性能. 关键词： 硼掺杂纳米金刚石薄膜 退火 微结构 电学性能     

Ag与YBa2Cu3O7-δ超导薄膜接触电阻的研究

本文系统研究了Ag/YBCO薄膜退火后Ag膜微观形貌与相应接触电阻率以及它们之间的关系,得到了在最佳退火温度(475℃左右)退火后ρc为6×10-8Ω*cm2(77K),并对接触电阻率随不同退火温度的变化进行了解释.此外,对于Ag与YBCO薄膜和Ag与YBCO块材之间的接触电阻率随退火温度的变化规律进行了比较并解释了其差异的原因.     

连续离子层吸附反应沉积后硫化法制备柔性铜锌锡硫薄膜太阳电池

在柔性钼箔衬底上采用连续离子层吸附反应法(successive ionic layer absorption and reaction)制备ZnS/Cu2SnSx叠层结构的预制层薄膜,预制层薄膜在蒸发硫气氛、550 C温度条件下进行退火得到Cu2ZnSnS4吸收层.分别采用EDS,XRD,Raman,SEM表征吸收层薄膜的成分、物相和表面形貌.结果表明,退火后薄膜结晶质量良好,表面形貌致密.用在普通钠钙玻璃上采用相同工艺制备的CZTS薄膜表征薄膜的光学和电学性能,表明退火后薄膜带隙宽度为1.49 eV,在可见光区光吸收系数大于104cm 1,载流子浓度与电阻率均满足薄膜太阳电池器件对吸收层的要求.用上述柔性衬底上的吸收层制备Mo foil/CZTS/CdS/i-ZnO/ZnO:Al/Ag结构的薄膜太阳电池得到2.42%的效率,是目前报道柔性CZTS太阳电池最高效率.     

GaN基紫光LED的高反射率p型欧姆接触

研究用于GaN基大功率倒装焊(Flip-chip)紫光LED(UV-LED)的高反射率p型欧姆接触的电学和光学性能。用磁控溅射的方法在GaN基LED外延片表面沉积了不同厚度Ag,Al,Au和Pd四种金属,测量了样品的反射率和透射率。结合同步辐射高强度X射线衍射和AFM对金属薄膜的晶体结构进行分析,并对表面形貌进行了观测,对由金属薄膜构成的多层膜结构及其对光反射率的作用机理进行了研究。测量结果表明,在入射光波长为400nm时,Ni/Au/Ag和Ni/Au/Al电极的反射率比Ni/Au的反射率提高了三倍。同时与p-GaN有良好的欧姆接触特性。     

传输线模型测量Au/Ti/p型金刚石薄膜的欧姆接触电阻率

采用传输线模型测量了重B掺杂p型金刚石薄膜(约10²⁰cm^-3)上Ti/A u欧姆接触电阻率ρ_c,测试了500℃退火前后及大电流情况下的I-V特性,研究 了退火对ρ_c的影响.结果表明,重掺杂和退火工艺是改善欧姆接触的有效手段. ρ_c随测试温度的变化表明金属/半导体接触界面载流子输运机制为隧道穿透.而 光照对ρ_c影响的分析表明金刚石可作为理想窗口材料.测试得到的最低ρ _c值约为10^-4Ωcm². 关键词： 金刚石薄膜 欧姆接触 接触电阻率     

不同[Cu]/[In]比例的CuInS2薄膜的特性

采用连续离子层吸附与反应方法在玻璃基板上按照不同[Cu]/[In]的比例制备了CuInS₂薄膜,并在400 °C退火30 min. 对薄膜的晶体结构和晶粒尺寸用X射线衍射方法进行了表征,原子力显微镜测定薄膜的表面形貌. 研究不同的[Cu]/[In]比例对薄膜光学和电学性能的影响. 采用直流两探针法在300～470 °C测定CuInS₂薄膜的电阻率,随着[Cu]/[In]比例的增加,电阻率值越来越低. 溶液中[Cu]/[In]的比例明显影响CuInS₂薄膜的结构、电学和光学特性.     

不同成分比例CIGS薄膜及太阳电池的快速退火

研究了110~180 ℃（2 min）下的快速热退火对Cu(In,Ga)Se2(CIGS)薄膜特性及CIGS太阳电池性能的影响.结果表明：对于不同成分比例的CIGS（正常、富Cu、高Ga）电池来说,150 ℃,2 min的快速退火最利于电池性能及二极管特性的增加.其中,退火对富Cu电池的开路电压Voc改善最大,这是因为快速热退火对消除部分CIGS薄膜中的CuSex有积极作用,从薄膜的电阻率有少量提高,器件的短路电流Jsc有少量下降可以得到验证|而对于高Ga电池来说,填充因子FF的改善最大,这是因为高Ga样品的缺陷较多,退火会消除薄膜内部的部分缺陷,从而薄膜的迁移率及Jsc都有所提高,使得FF有较大的增加.     

不同成分比例CIGS薄膜及太阳电池的快速退火

研究了110~180 ℃(2 min)下的快速热退火对Cu(In,Ga)Se2(CIGS)薄膜特性及CIGS太阳电池性能的影响.结果表明:对于不同成分比例的CIGS(正常、富Cu、高Ga)电池来说,150 ℃,2 min的快速退火最利于电池性能及二极管特性的增加.其中,退火对富Cu电池的开路电压Voc改善最大,这是因为快速热退火对消除部分CIGS薄膜中的CuSex有积极作用,从薄膜的电阻率有少量提高,器件的短路电流Jsc有少量下降可以得到验证;而对于高Ga电池来说,填充因子FF的改善最大,这是因为高Ga样品的缺陷较多,退火会消除薄膜内部的部分缺陷,从而薄膜的迁移率及Jsc都有所提高,使得FF有较大的增加.     

低相变温度垂直取向的CoPtCu/Ag纳米复合膜

采用磁控溅射(Ag/Cu/CoPt)_n多层膜先驱体结合真空退火的方法制备了一系列CoPtCu/Ag纳米复合薄膜，通过优化薄膜中Ag以及Cu的含量，成功制备出了低相变温度垂直取向的CoPtCu/Ag纳米复合膜，该膜在450℃退火即可发生相变，该温度比目前所报导的CoPtAg纳米复合膜的相变温度降低了150℃. 实验结果表明，薄膜中一定含量的Ag元素能够有效诱导薄膜的(001)取向，Cu元素的加入能有效降低薄膜的有序化温度. 对于特定组分为Co₄₀Pt₃₆Cu₈Ag₁₆的薄膜，经500℃退火后已经显示了明显的(001)取向，垂直于膜面方向上的矫顽力为5.0×10⁵A/m，并且薄膜中晶粒尺寸仅为4—5nm，为将来CoPt-L1₀有序相合金薄膜用于超高密度垂直磁记录介质打下了基础. 关键词： 磁记录材料 CoPt 纳米复合膜     

Combustion synthesis of high-quality diamond film suitable for application in electronic devices

The purpose of this research is to elucidate the electrical characteristics of a diamond film synthesized by combustion flame and synthesize a diamond film suitable for application in electronic devices. When the film contains amorphous carbon, the dielectric loss increases, i.e., the electrical characteristics of the diamond film are degraded. We employed three methods to decrease the amorphous carbon in the diamond film—the detection of the optimal equivalence ratio, addition of hydrogen into synthesizing gas, and heat treatment (annealing) of the diamond film. All these methods can decrease the amount of amorphous carbon effectively, thus systematically changing the factors influencing the optimal synthesis for improving the electric characteristics of the film. We have successfully developed a method for preparing a high-quality diamond film with excellent electrical characteristics that has no dielectric loss in the wide frequency range (10²–10⁸ Hz).     

生长条件和退火对金刚石薄膜光学性质的影响

提出一种分析微波等离子体化学气相沉积工艺条件对金刚石薄膜的组成和光学性质影响的方法。采用红外椭圆偏振光谱仪来分析Si衬底上金刚石薄膜的组成和光学性质，研究微波等离子体化学气相沉积法生长条件和退火工艺对金刚石薄膜的消光系数和折射率的影响。实验表明金刚石薄膜中存在C—H、C=C、O—H和C=O键，生长条件对薄膜中C—H和C=C键的含量及薄膜的折射率影响较大；薄膜经过退火后薄膜的光学性质得到明显改善。     

Electrical characteristics of UV photodetectors based on ZnO/diamond film structure

Ultraviolet photodetectors based on ZnO/diamond film structure were fabricated. The properties of Au/ZnO contacts and effects of grain sizes on the electrical characteristics of photodetectors were discussed. Due to the bombardment with Au atoms and the annealing process, fine ohmic contacts were formed between Au electrodes and ZnO films. Dark currents and photocurrents of the photodetectors were related to sputtering time and the grain size of ZnO films. For the photodetector with a bigger grain size, a lower dark current and a higher photocurrent were obtained under 10 V bias voltage. The time-dependent photocurrent confirmed the carrier trapping effect.     

The effect of boron ion implantation and annealing on the microstructure and electrical characteristics of the diamond films

Diamond films were doped by boron ion-implantation with the energy of 120 keV. The implantation dose ranged from 10¹⁴ to 10¹⁷ cm⁻². After the implantation, the diamond films were annealed at different temperatures (600–750°C) for different times (2–15 min). Scanning Electronic Microscope, Raman and Secondary Ion Mass-spectrum were used to investigate the effect of boron ion implantation and annealing on the microstructure of the diamond films. The electrical resistivities of the diamond films were also measured. It was found that the best dose of boron ion-implantation into the diamond film was around 10¹⁶ cm⁻². The appropriate annealing temperature and time was 700°C and 2–5 min, respectively. After implantation, the resistivities were reduced to 0.1 Ω cm (almost nine orders lower than the unimplanted diamond films). These results show that boron ion implantation can be an effective way to fabricate P-type diamond films.     

AFM analysis of piezoelectric nanogenerator based on n-diamond/n-ZnO heterojunction

We have demonstrated a high performance piezoelectric nanogenerator by scanning a diamond-coated conductive tip on ZnO nanorod arrays in an AFM system with contact-mode. About 95% ZnO nanorods generate piezoelectric current due to the excellent mechanical and electrical properties of the tip. The tip's nitrogen-doped diamond coating is the key factor to maintain effective physical contact and electrical contact to ZnO nanorods, leading to efficient piezoelectric generation. Rectifying n⁺-n heterojunction is formed when the nitrogen-doped diamond tip contacted with a ZnO nanorod, which plays an important role in accumulating and releasing piezoelectric charges of the piezoelectric nanogenerator. Our research indicates that conductive diamond film is an ideal electrode for this type of piezoelectric nanogenerator.     

Annealing induced refinement on optical transmission and electrical resistivity of indium tin oxide

The effect of annealing condition on sputtered indium tin oxide （ITO） films on quartz with the thickness of 200 nm is characterized to show enhanced optical transparency and optimized electrical contact resistivity. The as-deposited grown ITO film exhibits only 65% and 80% transmittance at 532 and 632.8 nm, respectively. After annealing at 475 ℃ for 15 min, the ITO film is refined to show improved transmittance at shorter wavelength region. The transmittances of 88.1% at 532 nm and 90.4% at 632.8 nm can be obtained. The 325-nm transmittance of the post-annealed ITO film is greatly increased from 12.7% to 41.9%. Optimized electrical property can be obtained when annealing below 450 ℃, leading to a minimum sheet resistance of 26 Ω/square. Such an ITO film with enhanced ultraviolet （UV） transmittance has become an alternative candidate for applications in current UV photonic devices. The morphology and conductance of the as-deposited and annealed ITO films are determined by using an atomic force microscopy （AFM）, showing a great change on the uniformity distribution with finite improvement on the surface conductance of the ITO film after annealing.     

退火时间对硼掺杂纳米金刚石薄膜微结构和电化学性能的影响

采用高分辨透射电镜、紫外和可见光Raman光谱及循环伏安法研究了1000 ℃下退火不同时间的硼掺杂纳米金刚石薄膜的微结构和电化学性能. 结果表明,随退火时间的延长,薄膜中纳米金刚石晶粒尺寸逐渐减小.当退火时间为0.5 h时, 金刚石晶粒尺寸由未退火样品的约15 nm减小为约8 nm, 金刚石相含量增加;当退火时间为2.0 h时,金刚石晶粒减小为2—3 nm, 此时晶界增多,金刚石相含量减少;退火时间为2.5 h时纳米金刚石晶粒尺寸和金刚石相含量又略有上升.晶粒尺寸和金刚石相含量的变化表明薄膜在退火过程中发生了金刚石和非晶碳相的相互转变.可见光Raman光谱测试结果表明,不同退火时间下, G峰位置变化趋势与I_D/I_G值变化一致,说明薄膜内sp²碳团簇较大时, 非晶石墨相的有序化程度较高.退火0.5, 1.0, 1.5和2.0 h时, 电极表面进行准可逆电化学反应,而未退火和退火时间为2.5 h时电极表面进行不可逆电化学反应.退火有利于提高薄膜电极的传质效率, 退火0.5 h时薄膜电极的传质效率最高,催化氧化性能最好.较小的晶粒尺寸、 较高的金刚石相含量以及纳米金刚石晶粒的均匀分布有利于提高电极表面反应的可逆性和催化氧化性能.     

氢退火的BZO前电极对非晶硅薄膜太阳能电池性能的影响

采用低压化学气相沉积方法在玻璃衬底上制备了B掺杂的ZnO（BZO）薄膜,通过氢退火对BZO进行处理,然后作为前电极进行了非晶硅薄膜太阳能电池的制备及性能研究。结果表明：在氢气气氛下退火后,BZO薄膜的载流子浓度基本无变化,但Hall迁移率显著提高,这使得BZO薄膜的导电能力提高;当采用厚度较小、透光率较高的BZO薄膜进行氢退火后作为前电极结构时,非晶硅薄膜太阳能电池的短路电流密度提高0.3~0.4 mA/cm²,电池的转化效率提高0.2%。实验结果可为通过优化前电极结构来提高非晶硅薄膜太阳能电池转化效率提供一种简易的方法。     

W过渡层结合界面对金刚石薄膜在WC-6%Co上的附着力的影响

 在微波等离子体化学气相沉积装置中,采用负偏压形核等方法,研究两种不同的W过渡层/基体结合界面对金刚石薄膜与WC-6%Co附着力的影响。采用氢等离子体脱碳、磁控溅射镀W、高偏压碳化等方法,在YG6衬底表面形成化学反应型界面,W膜在碳化时和基体WC连为一体,极大地增加了W膜与基体的附着力,明显优于直接镀钨、碳化形成的物理吸附界面。在高负偏压下碳化,能提高表面粗糙度,增加膜与基体机械钳合,而负偏压形核增加核密度,从而增加膜与基体的接触面积,结果极大地提高了金刚石薄膜的附着力。